Find a Heating Engineer you can trust in Hemel Hempstead.

How Much Does A Boiler Repair Cost?

An annual service for your boiler might not seem important and may be easy to postpone to another day, but when it happens to breakdown due to lack of adequate attention, this can be quite painful and also costly.

Before you start thinking about the cost of repairing your boiler, the first thing you’ll need to confirm is whether or not your boiler is still covered by the manufacturer’s warranty. You’d be amazed some warranties can last for as long as 12 years, if yours is still on then you can save yourself a huge amount of of money on your boiler repair. As a result, it’s always crucial to keep the details of your warranty somewhere safe, so you can read them from time to time. You never can tell when the rainy day will come!

Most boiler warranties will require your to get your boiler serviced on an annual basis by a licensed and qualified technician. The cost of an annual boiler service is affected by the time of the year you wish to get it done. When boilers are less useful during the summer months, an annual service is usually relatively cheap when compared to the cold months. Around this period, a boiler service will normally cost within the range of £100 to £150, however for a more accurate quote it’s advisable to contact a couple of professionals and compare their quotes.

The cost of getting a boiler repaired will be affected by a couple of factors including your boiler’s make, the age of the boiler as well as your location and how urgent you need it done. If you have a dead boiler, the cost will typically range from £96 to £348 and a boiler displaying a fault code will cost within the range of £90 to £275. Generally, repairing a boiler will cost within the range of £90 to £400 based on the several factors stated above.

How To Install A Gas Cooktop In An Island

Are you thinking about installing a gas cooktop in your kitchen island? If yes, then you must know that there are clearance requirements that must be met (before you proceed) between the cut out and the countertop’s edge. Basically, there are incremental requirements for island installation due to the fact that it does not make an assumption that the product is going to be fitted against a rear wall that acts to protect the back of the unit. As a result, while doing an island install we must put the safety of the product into consideration much more that we do a standard install. What’s more? This island clearance requirement develops from a third-party agency and is a standard with all brands. So how do you install a gas cooktop in an island having the aforementioned requirements in mind?

• Use a foil tape to line the inside edges of the cut out. The function of this is to prevent heat damage as well as countertop’s discolouration. Put the cooktop top on a secured surface.

• Identify the pipe coming out of the cooktop’s side or bottom and brush onto the threads of the manifold entrance.

• Pass the pressure regulator onto the entrance of the manifold and make use of a wrench to tighten it.

• Brush the pipe joint compound onto one of the flare union adaptor’s threads and pass it into the regulator’s open end. Make it slightly tight with a full turn of the wrench.

• Connect the flare union adaptor’s open end with the flexible appliance connector hose, upon brushing on pipe joint compound.

• Put foam tape on the cooktop underside’s edges, if your cooktop comes with a glass burner plate.

• Turn the cooktop to set it into the cutout.

• Apply pipe-joint compound onto the flare union adaptor left and secure it firmly into the gas shutout valve.

• Connect the flexible hose connector’s free end with the flare union adaptor.

Biomass boilers do require some maintenance. Many manufacturers recommend servicing twice a year, although this is often included in the installation cost. Many systems have automatic fuel loading that removes the need to manually load fuel. You will need to remove the ash from the boiler, but this is as easy as emptying a vacuum cleaner.

If your boiler is leaking, there are some checks that you can do yourself. However, you should never attempt to repair your boiler yourself – only a Gas Safe-registered engineer should conduct repairs.

There are 3 main reasons why your boiler might be leaking: there’s a pressure valve fault, a temperature valve leak or corrosion in the system. An engineer will be able to spot the problem quickly, but in the meantime there are a few things you can do:

Check the pipe fittings

If your boiler is leaking water around the pipe fittings, it could be an installation fault and you should get in touch with the engineer that fitted it. You can check the pipe fittings by drying the area then waiting to see if the water appears again. If it does, you may be able to do a ¼ turn of the pipe to stop it. However, you should still call the engineer that installed it to ask them to check the PTFE tape on the inside.

Inspect the seals

Over time, the rubber seals on a boiler can start to perish, so if you have an old boiler this could be the source of your leak. If you have a new boiler, it could be caused by your boiler running over pressure.

Heat exchanger corrosion

Unfortunately, if a boiler engineer discovers that the boiler is leaking water from the heat exchanger, this is the end of the road for your system. The heat exchanger is the most expensive part of your boiler, so it makes more financial sense to replace your boiler with a newer, more efficient model rather than try to replace it.

To ensure that your boiler is safe and operating efficiently, it’s essential to have it serviced on a regular basis.

Generally, a boiler service will deliver a wide array of benefits which includes the opportunity to identify safety issues like a possible leak of carbon monoxide, efficient use of energy and reduction in energy bills, prevention of breakdowns, a valid warranty when the boiler is serviced regularly by a qualified engineer as well as an extended lifespan. So what exactly does a boiler service cover? This guide will give you a good insight as to what happens during that service.

Before we get started, it’s very important to note that the work done is always as good as the engineer you employ. Therefore, it’s advisable to make sure your preferred engineer is qualified before proceeding with the service. Below are some of the basic practices the engineer may perform during their visit.

• Thorough Inspection

During the visit, the engineer will carry out a detailed examination of your boiler to ensure it still meets the current standards while also making sure that there are no leaks or corrosion. What’s more? They’ll also examine the boiler’s flame for any faults.

• Boiler Casing Removal

The boiler casing will be detached to check all components and ensure they’re free from all forms of dirt and see to it that they’re all working just as they should. This will include examination of the heat exchanger, main injector, burner and spark probe.

• Flue Examination

The engineer will inspect the flue terminals to make sure there are no form of obstructions and it’s also safely installed.

• Gas Pressure Examination

This is done to make sure the heating system is operating at the right pressure.

The short answer to this is no! Smart thermostats can still be used without WiFi, however, they’ll be deprived of some certain capabilities and innovative features that comes mainly due to their ability to connect to the internet. As a result, the smart thermostat will only be functional for basic task such as heating and cooling control. In other words, making use of a WiFi connection will be in your best bet to enjoy the multiple juicy benefits that comes with a smart thermostats such as remote monitoring, ability to connect to other devices and display local weather conditions and much more. And what’s the use of purchasing a smart thermostat if you’d not be able to enjoy these remarkable features?

However, even when you have a WiFi, it’s expected for the connection to fail at times. When this happens, what will be the impact on your smart thermostat? Let’s have a closer look!

• As you would have expected, when your smart thermostat is disconnected from WiFi, features that are controlled with the mobile app would all be impacted. And this might be a big headache when you wish to access these features and control remotely when far away from home.

• When your smart thermostat connection to WiFi fails, all live updates and alerts would be affected. This implies that you’d stop seeing updates, reports and notifications on your mobile device. As a result, you’ll not be notified in case of an emergency like electricity cut-outs, water leaks, humidity and temperatures exceeding the set levels as well as thermostat’s low battery.

• The lack of a WiFi connection might have taken away all the juicy advantages of having a smart thermostat, but one function that remains unaffected is the basic one - the control of your home’s heating and cooling system. In other words, if your smart thermostat is offline, your home will still be heated and cooled to the thermostat’s set temperature.

Condensing boilers are the in-thing when it comes to modern heating systems in UK homes and across the globe for a good reason. This is primarily due to the fact that condensing boilers happens to be highly efficient as it enables the fuel you’re burning to heat up your home go a lot further. Having a new high efficiency condensing boiler rather than an old G-rated non condensing boiler will not only enhance your heating controls, but also save you a lot of money annually. In this article, we’re going to take you through the basics of a condensing boiler. Let’s take a closer look!

If you’re interested in getting a greener and more efficient boiler, you simply can’t afford to look beyond a high efficiency condensing boiler. This is purely due to the fact that these condensing boilers happens to make a better use of the heat they’re able to produce from burning fuels like oil or gas ( in other words, they require less heat from the burner, which makes them a lot more efficient).

So how does a condensing boiler work? Unlike a non-condensing heat-nly boiler, some heat will be wasted in form of hot gases which are released from the flue. Meanwhile a condensing boiler captures some of the heat from these gases and puts them to use for heating up water that’s coming back from your central heating system. As a result, it requires just a minimal heat from the burner which make the boiler more efficient.

You should take note that all new modern boilers are condensing boilers. Therefore if you’re planning to replace an old boiler with a new one, you’ll definitely be buying a new condensing boiler and benefit from all the efficiency and savings that comes with it.

How Much Is A Gas Safety Certificate?

If you’re a landlord in the UK, then you’d know a gas safety certificate is a legal requirement. If yes, then you’d probably like to know how much it’ll cost to get a gas safety certificate so you can make plans on obtaining one for your property. In this article, you’ll find all you need to know about the amount you’re expected to pay for a gas safety certificate in the UK.

First and foremost, let’s look into the use of the certificate. Basically, a gas safety certificate is the legal inspection of your property’s gas appliances which would be done on an annual basis. Only an approved Gas Safe engineer is allowed to carry out this statutory check. Ultimately, if you own rental properties in the country, this is a requirement you can’t afford to overlook to ensure the safety of your tenants.

Furthermore, included in this inspection are each and every gas appliances, chimneys, pipework as well as flues in the property. In recent times, several individuals make use of fewer gas appliances which ultimately implies that they may only need the servicing of their gas fire. Once you’ve passed the inspection, you’ll be given your CP12 certificate which must be kept for a minimum of two years. A copy should also be provided to your tenants within 28 days of issue. So how much will it cost to get a gas safety certificate?

Depending on your location in the UK as well as the number of gas appliances incorporated, the average cost of a gas certificate will range between £60 to £90. The Gas Safe engineer will carry out the task as a fixed and statutory job.