Find a Heating Engineer you can trust in Roy Bridge.

How Much Does A Boiler Repair Cost?

An annual service for your boiler might not seem important and may be easy to postpone to another day, but when it happens to breakdown due to lack of adequate attention, this can be quite painful and also costly.

Before you start thinking about the cost of repairing your boiler, the first thing you’ll need to confirm is whether or not your boiler is still covered by the manufacturer’s warranty. You’d be amazed some warranties can last for as long as 12 years, if yours is still on then you can save yourself a huge amount of of money on your boiler repair. As a result, it’s always crucial to keep the details of your warranty somewhere safe, so you can read them from time to time. You never can tell when the rainy day will come!

Most boiler warranties will require your to get your boiler serviced on an annual basis by a licensed and qualified technician. The cost of an annual boiler service is affected by the time of the year you wish to get it done. When boilers are less useful during the summer months, an annual service is usually relatively cheap when compared to the cold months. Around this period, a boiler service will normally cost within the range of £100 to £150, however for a more accurate quote it’s advisable to contact a couple of professionals and compare their quotes.

The cost of getting a boiler repaired will be affected by a couple of factors including your boiler’s make, the age of the boiler as well as your location and how urgent you need it done. If you have a dead boiler, the cost will typically range from £96 to £348 and a boiler displaying a fault code will cost within the range of £90 to £275. Generally, repairing a boiler will cost within the range of £90 to £400 based on the several factors stated above.

The Hive thermostat stand is relatively easy to install, however if you lack the necessary training or experience, this is a task you might want to leave to a professional to guarantee the best result while also saving you money and time. This guide will give you a good insight into the Hive thermostat installation process.

The installation of a Hive thermostat does require it to be connected to your home boiler. For this reason we always recommend you get a professional to install it. However once install the Hive Smart Thermostat is very easy to operate and move the controller around your home. To get started, you can follow these steps:

• Press the lever at the lower side of the thermostat and pull away from the front to detach the back plate of your device.

• Once done, simply hang the thermostat on the stand back plate and ensure it holds firmly in place

When it comes to Hive thermostat installation, you might also want to consider the positioning of the device in such a way to heat your home even more efficiently as its designed to be very sensitive to temperature. To identify the best spot for your Hive thermostat, let’s take a look at some of the dos and don’ts.

A Few Dos:

• Do maintain the position of your Hive Thermostat to keep a stable connection with the receive and Hive Hub.

• Do ensure that the position chosen is the centre of your home or a frequently used room.

• Do place the thermostat about 1 to 1.5 metres from floor.

• Do ensure that your thermostat is in a close proximity with the hub and receiver for a better functionality.

A Few Don’ts:

• Don’t place your Hive thermostat stand close to radiators, direct sunlight or other heat sources,

• Don’t position your device near or at places that can expoerience a sudden change in temperature such as the front or back door.

• Don’t leave your thermostat too close to curtains or ornaments.

Biomass boilers can be designed to work with other kinds of heating. The most common of these is solar thermal. This is a popular renewable energy pairing. Solar thermal heating will meet your hot water needs during the summer while a biomass boiler can operate as a backup during the winter when solar thermal panels do not perform as well.

Re-pressurising your boiler means that you allow more water to enter system via the filling loop. It can be easy to re-pressurise your boiler yourself. Always check your manual, but there are some simple steps you can take to restore pressure to your boiler:

1. Switch off your boiler and let it cool completely
2. Make sure both ends of your filling loop are attached
3. Open both valves to allow cold water into the system – you’ll hear it start to move
4. Look out for your pressure gauge to show 1.5 bar
5. Close both valves
6. Switch your boiler back on
7. Undo both ends of your filling loop and remove it. Remember some water might come out, so be ready to catch some spillage!

Are Electric Radiators Expensive To Run?

Just like many home additions, the running costs of electric radiators varies largely on a number of factors. Great number of electric radiators typically comes with an in built thermostat which is designed to turn itself off automatically when not in use in order to save energy.

However the energy provider’s set electricity charge tariff will also have a great influence on an electric radiator’s running cost. Let’s take a look at the running costs of an electric radiator!

A 600 Watt electric radiator ( on a standard electricity tariff) will usually have a running cost ranging between 4 to 6 pence each hour. However you should also take note that this scenario might change in situations whereby the electric radiator is not calling for heat the full 60 minutes of each hour. And this is more likely to be the situation as the thermostat is programmed in such a way that enables it to turn itself off immediately there’s an achievement of your required room temperature level - usually within 10 minutes from the time it was switched on. As a result of this, the running cost per hour of electric radiators will be greatly reduced to just about 1 to 2 pence.

It’s also important to note that enhancing the insulation of your home can go a long way to add to the heat retention value of each room. Consequently, the duration at which the electric radiator calls more heating will be significantly reduced, which in turn, implies a lower electricity bill.

Another key factor that can play a huge role in saving on your heating bills is the programming as well as usage of your electric radiators. Every radiator comes with an independent digital thermostat with a number of 24/7 programming options to help achieve maximum efficiency. When the radiator is properly set according to your lifestyle, you can save as much as 50 percent on your heating bills.

Biomass boilers will work with existing central heating systems, presuming this is not decades old, whether they use radiators or under floor heating. A surveyor will check the existing system you have in place before quoting for or recommending a biomass boiler to you.

Ad hoc visits from your engineer to fix small issues with your heating system may actually seem cheaper and a lot more affordable, however when a boiler is ripe enough for a change these small issues are always never ending. Over some period of time, these small issues will inevitably get worse and the idea of “mend and make do will be an absolutely false economy. The best course of action in this sort of event is to find a replacement boiler to install as soon as possible. In this article, we’re going to give you some hints that’ll show you when your boiler needs to be replaced. Now let’s take a look!

✓ Insufficient hot water. Here, you’ll have to check the size of your hot water cylinder. It’s crucial to make sure that your boiler is rightly sized to power your heating as well as hot water circuit in line with your demands. You should always seek the advice of a heating expert who can recommend whether to fix or replace the boiler.

✓ Strange noises. It’s normal for components of the boiler to become worn or damaged over time. Replacing the particular component that’s causing the knocking or rattling may seem cost effective at first but more often than not, the noises usually signal a bigger issue which is likely to build up over time. Hence, it’ll be a lot more logical to replace the boiler itself.

✓ Regular repair of your boiler. It’s essential to have your heating system serviced by a Gas Safe engineer on an annual basis. However, when you have to call them more often than once a year for your yearly maintenance, it may be a wise decision to consider getting a replacement.

✓ Other events whereby you may need a new boiler includes when you can’t get the right temperature in your room, when the radiators don’t heat up as they should, when your boiler leaks and if your boiler still has a pilot light.

How To Install An Oil Boiler Heating System

Just like several other skills, the installation of an oil boiler heating system can be a challenge. It requires enough persistence to actually get right, so if you’re the type with little patience, we’d recommend you hire the services of a professional oil boiler heating system fitter who can guarantee the best results and save you time and extra money due to potential damages.

To install your boiler system yourself, it’s always advisable to start by getting the information on the best installation processes from the supplying company which will go a long way to save you from future headaches. However, we’ve put together this guide to give you a basic knowledge on how its done. Let’s have a look!

lRead Instruction Manual

• Carefully read and digest the instruction manual thoroughly.

• Make sure you understand the installation diagrams

• Spread out the materials and get familiar with them.

lFigure Out What Goes Where

• Take your time to determine where everything goes in relation to the others.

• Identify the new radiator’s position.

• Get sufficient sealants to prevent possible leakages inside the walls.

lIdentify The Pipe Routes

• Determine the pipe routes while fitting the new radiators

lInstall The Boiler

• Turn off water and all electrics

• Fit the boiler into the wall

• Make sure the fittings are secured.

lInstall The Radiator

• The effectiveness of your home’s heating system is as good as the radiators you incorporate and how good they’re installed.

• You may have to utilize extra radiators in large open plan kitchens and living rooms (for effective heating).

lOffer Ventilation

• Once you’ve successfully installed the new radiator, a small dose of air ventilation would be needed.

• Turn the key of each valve located at the bottom, do not stop until a little amount of water spills over the top of the unit.