Find a Heating Engineer you can trust in Scunthorpe.

How To Fix A Broken Boiler

To fix any problem when it comes to home appliances, the first step is always to identify the problem while also carrying out thorough checks - a broken boiler is not an exception. Putting enough time and effort in diagnosing a problem can go a lot way to save you both time and money. So here are some of the steps you can take to fix your broken boiler before you put a call out to a licensed engineer.

✓ Check to confirm if your pilot light is on. Whenever you’re facing some issues with your boiler, this should always be the first thing you do. The pilot light being on speak volumes, if the light is off then there’s absolutely no way the flame can start the appliance’s gas supply. You should try to put it back on, if off. To do this, you simply have to follow the detailed instructions on your boiler’s manual strictly. If after following these actions to the letter and the issue remains the same, then you’d probably need the services of an a qualified engineer. Never try to fix the issue on your own.

✓ Check the pressure. The solution to the headaches might sometimes be as simple as examining your appliance’s pressure gauge. Here, the good numbers are around 1.0 or1.5, if it happens to fall below this, then you should open the boiler’s instruction manual. You can also inspect your radiator valves for any leaks. You’d have to call in a specialist to solve the issue.

✓ Check the thermostat. Here, it’s important to note that a faulty thermostat doesn’t necessarily imply a broken boiler. It may just signify that you need to replace your thermostat. Simply check to ensure that your thermostat is turned on and temperature is at the appropriate degree.

If you choose to install an LPG boiler, you’ll need to find an LPG supplier. They’ll deliver fuel to you every time your storage tank runs low. You can even rent a storage tank from them if you don’t want to buy one. Make sure you know who your local suppliers are and where they are based.

In recent times, home and property owners are constantly looking for ways in which to enhance both energy efficiency and sustainability especially as the world draws closer and closer to energy-efficient technology. The Nest thermostat is a great example of this fact as its designed in such a way to save energy while also cutting heating and cooling costs. And an interesting fact is, you’re not limited to using just a single Nest thermostat in your home as multiple of the device can successfully run together to maintain a consistent level of temperature monitoring as well as energy efficiency. What’s more? You can add up to 20 Nest thermostat and 18 temperature sensors in a home.

It’s very unlikely that you’re going to need this many thermostats in your home, but if you’d like to add a second the process is quite straightforward. However, we’d recommend you employ the services of a seasoned professional especially if you lack the required training or experience to pull this off to save yourself some time and money.

To get started, simply download the associated Nest app to add Nest devices. Now let’s have a look at the processes involved in adding a second Nest thermostat to your home.

• Open the app.

• Go to the top left corner of the main screen and click on the menu button.

• Pick the location or home you’re adding the device to.

• Go to the top right corner and select the “settings.

• Once done, then click on the Add Product “Plus button.

Upon a successful addition of the second thermostat, the app will guide you through the initial set up steps. Google also offers a very helpful guide if you’re unfamiliar with the initial configuration.

Re-pressurising your boiler means that you allow more water to enter system via the filling loop. It can be easy to re-pressurise your boiler yourself. Always check your manual, but there are some simple steps you can take to restore pressure to your boiler:

• Switch off your boiler and let it cool completely

• Make sure both ends of your filling loop are attached

• Open both valves to allow cold water into the system – you’ll hear it start to move

• Look out for your pressure gauge to show 1.5 bar

• Close both valves

• Switch your boiler back on

• Undo both ends of your filling loop and remove it. Remember some water might come out, so be ready to catch some spillage!

If your property is not connected to a gas main, oil boilers are a great alternative to gas boilers and more efficient than LPG alternatives. They can also be paired well with renewable sources. However, if your property is connected to the gas mains, there is generally no reason to switch to an oil boiler, as you will need to have oil delivered to an extra storage tank.

Re-pressurising your boiler means that you allow more water to enter system via the filling loop. It can be easy to re-pressurise your boiler yourself. Always check your manual, but there are some simple steps you can take to restore pressure to your boiler:

1. Switch off your boiler and let it cool completely
2. Make sure both ends of your filling loop are attached
3. Open both valves to allow cold water into the system – you’ll hear it start to move
4. Look out for your pressure gauge to show 1.5 bar
5. Close both valves
6. Switch your boiler back on
7. Undo both ends of your filling loop and remove it. Remember some water might come out, so be ready to catch some spillage!

Are Electric Radiators Expensive To Run?

Just like many home additions, the running costs of electric radiators varies largely on a number of factors. Great number of electric radiators typically comes with an in built thermostat which is designed to turn itself off automatically when not in use in order to save energy.

However the energy provider’s set electricity charge tariff will also have a great influence on an electric radiator’s running cost. Let’s take a look at the running costs of an electric radiator!

A 600 Watt electric radiator ( on a standard electricity tariff) will usually have a running cost ranging between 4 to 6 pence each hour. However you should also take note that this scenario might change in situations whereby the electric radiator is not calling for heat the full 60 minutes of each hour. And this is more likely to be the situation as the thermostat is programmed in such a way that enables it to turn itself off immediately there’s an achievement of your required room temperature level - usually within 10 minutes from the time it was switched on. As a result of this, the running cost per hour of electric radiators will be greatly reduced to just about 1 to 2 pence.

It’s also important to note that enhancing the insulation of your home can go a long way to add to the heat retention value of each room. Consequently, the duration at which the electric radiator calls more heating will be significantly reduced, which in turn, implies a lower electricity bill.

Another key factor that can play a huge role in saving on your heating bills is the programming as well as usage of your electric radiators. Every radiator comes with an independent digital thermostat with a number of 24/7 programming options to help achieve maximum efficiency. When the radiator is properly set according to your lifestyle, you can save as much as 50 percent on your heating bills.

How Much Is A Landlord Gas Certificate?

Do you know as a landlord in the UK, not only does the law requires you to conduct an annual check on all your gas appliances and chimney, but you’d also have to pay for it? Hence, giving birth to the commonly asked question, how much is a landlord gas certificate? With so many variances in CP12 certificate prices everywhere, it can be so confusing knowing the actual one you’re expected to pay. Just by surfing the internet alone you’d come across loads of ads claiming they can help you with a cheap gas safety certificate only to discover that reverse is the case when you reach out to them. Here, you’ll get to know the real amount you’re expected to pay for the annual checks on your gas appliances and chimney.

First and foremost, let’s look at what a Gas Safety Certificate really is. This is a certificate that’s given out to landlords and property management companies after a check has been carried out on all their gas appliances and chimney. This statutory check is expected to be done every 12 months to ensure the safety of all those who make ue of your rental property. Homeowners living in ther property are not required by the law to conduct annual gas safety check, but it’s highly recommended that you get in touch with a Gas Safety engineer to ensure the safety of both you and your loved ones.

As a landlord in the UK, to get all your gas appliances and chimney inspected by an approved Gas Safety engineer and obtain your Gas Safety Certificate, you’re expected to pay within a range of £55 to £65. However, you should note that this cost will increase depending on the number of gas appliances you have (about 30% increase for each additional gas appliance).