Find a Heating Engineer you can trust in Isle Of Canna.

Installing your Nest thermostat may not be as easy as screwing a light bulb, but we can also assure you that it isn’t very difficult either. However, if you lack the needed training or experience to pull it off, we’d recommend you hire the services of a professional in order to save yourself some time and money. This guide will give you some quick and easy steps to follow and ensure you make no errors during the installation process.

Once installed removing the Nest Thermostat can be done. To get started, you’ll need just a Philips head screwdriver which Nest has thoughtfully provided with the device.

• Turn off the Nest Thermostat by switching the circuit breaker to the off position.

• Label or mark your old thermostat’s wires. However, if you notice your thermostat is tagged 120v or 240v, or possesses thick wires, do not connect the wires to the Nest as you have a high voltage system.

• Uninstall the old thermostat by locating detaching the wires coming out from the wall into the thermostat. Once done, simply unscrew the device from the wall

• Mark the spot of your thermostat. Do this by threading wires through the Nest base plate’s centre incorporate the tiny bubble level. Once done, you can then use a pencil to mark te two screw holes.

• Attach the trim plate. If you wish to cover the screw holes, simply install the trim plate in the Nest box’s bottom to the base plate.

• Using the screws and screwdriver, attach the Nest base to the wall.

• Connect the wires to the Nest by putting the labelled wires in the Nest’s corresponding ports.

• Put the Nest display by lining up the connector on the display’s back.

• Turn on the power by switching the circuit breaker to the on position

• Connect your Nest thermostat to the WiFi network.

• Follow the on-screen guide and set the temperature.

• Use your smartphone or tablet to download the Nest thermostat’s mobile app to monitor and control your device remotely.

Re-pressurising your boiler means that you allow more water to enter system via the filling loop. It can be easy to re-pressurise your boiler yourself. Always check your manual, but there are some simple steps you can take to restore pressure to your boiler:

1. Switch off your boiler and let it cool completely
2. Make sure both ends of your filling loop are attached
3. Open both valves to allow cold water into the system – you’ll hear it start to move
4. Look out for your pressure gauge to show 1.5 bar
5. Close both valves
6. Switch your boiler back on
7. Undo both ends of your filling loop and remove it. Remember some water might come out, so be ready to catch some spillage!

How To Install A Gas Cooktop In An Island

Are you thinking about installing a gas cooktop in your kitchen island? If yes, then you must know that there are clearance requirements that must be met (before you proceed) between the cut out and the countertop’s edge. Basically, there are incremental requirements for island installation due to the fact that it does not make an assumption that the product is going to be fitted against a rear wall that acts to protect the back of the unit. As a result, while doing an island install we must put the safety of the product into consideration much more that we do a standard install. What’s more? This island clearance requirement develops from a third-party agency and is a standard with all brands. So how do you install a gas cooktop in an island having the aforementioned requirements in mind?

• Use a foil tape to line the inside edges of the cut out. The function of this is to prevent heat damage as well as countertop’s discolouration. Put the cooktop top on a secured surface.

• Identify the pipe coming out of the cooktop’s side or bottom and brush onto the threads of the manifold entrance.

• Pass the pressure regulator onto the entrance of the manifold and make use of a wrench to tighten it.

• Brush the pipe joint compound onto one of the flare union adaptor’s threads and pass it into the regulator’s open end. Make it slightly tight with a full turn of the wrench.

• Connect the flare union adaptor’s open end with the flexible appliance connector hose, upon brushing on pipe joint compound.

• Put foam tape on the cooktop underside’s edges, if your cooktop comes with a glass burner plate.

• Turn the cooktop to set it into the cutout.

• Apply pipe-joint compound onto the flare union adaptor left and secure it firmly into the gas shutout valve.

• Connect the flexible hose connector’s free end with the flare union adaptor.

Can You Replace Storage Heaters With Electric Radiators?

The short answer to this question is yes. If your outdated storage heater is not heating your home the way it should, you’ll find a better replacement in electric radiators.

Being more modern and efficient, electric radiators offer a wide range of benefits which storage heaters can only dream of. Let’s have a look.

• Unlike storage heaters, electric radiators do not need to be charged up the night before which makes it totally controllable as you do not have to guess what your heating needs will turn out to be the next day.

• The above benefit leads to an even better one as the controllability quality of electric radiators makes them a lot more efficient than storage heaters. Electric radiators usually comes with programmable timers and thermostats which allows you to set various heating schedules for each of your rooms, meaning you’re only heating when and where its needed.

• Unlike some storage heaters, electric radiators do not cause wall blackening and also happen to more elegant and stylish.

• Electric radiators are not tough on allergies like storage heaters as they do not depend mainly on convection to heat

• Electric radiators also have an easy installation process with all you need to do to switch from storage heater to one being the removal of the former and inserting the radiators into the sockets.

However, if you want to make a switch to electric radiators, there’s the need to change to a standard electricity tariff from your economy tariff. And while the standard electricity tariff rates may be more expensive than the night time rate provided by Economy 7, the standard tariff rates are a bit cheaper than the daytime Economy rate. You’ll also get to use much less of electricity while also saving money on your heating bills and more.

The simple answer to this question is yes. The Google Nest thermostats are built in such way that makes it compatible with most 24V systems including the older systems. The device is functional with all common types of fuel such as electricity,natural gas as well as oil. However, before purchase it is vital to determine if your thermostat is also compatible. What’s more? The Nest thermostats is also designed to be usable even without the existence of a C wire (common wire) in your home, although a new C wire installation may be required.

Furthermore, Nest Learning Thermostat is compatible with multiple central heating system such as combi boiler systems, air source and ground source heat pumps (heating only) as well as heat only boiler. Now let’s take a look at the Nest thermostat compatibility!

• The majority of the 24 V systems ( including older systems) are compatible with Google Nest thermostat. They can be incorporated with each and every common types of fuel such as oil, natural gas as well as electricity.

• Prior to the installation of Google Nest thermostat, you can make use of the Google Home or Nest app for proper guidance and to notify you if your system is compatible. It will also give you a bespoke thermostat wiring guide.

• To check the compatibility of your system, you can also check with the Google’s online compatibility checker before purchase.

When your boiler is being replaced you won’t have hot water or central heating. If you don’t mind this you can stay in your home, and use portable electric heaters if needed. Most installers undertake a power flush before installing a new boiler now and this can cause muck and debris from the pipework, so you may wish to get out of the way while this is happening!

How Do You Bleed An Oil Boiler?

Bleeding air between the oil supply and an oil fired boiler’s burner is a process that’s often required when the system has run out of oil and the burner has stopped working. Upon refilling the oil tank, the air that has been trapped within the oil pipe when empty has to be freed to ensure that the oil reaches the burner and allows it to start again. So how do you go about the process?

First and foremost, it must be noted that it’s always better to be on the look out for the amount of oil in your fuel tank and get it refilled before it runs out. However, if it does run out, you can take the following steps:

• Identify the burner

The burner is a red plastic cover and it’s usually positioned on the bottom part of the boiler (mostly inside the boiler casing). Once identified, inspect it to see if the lockout button is lit red. If yes, simply unscrew and detach the burner’s red case using a flat head screwdriver.

• Identify the oil pump

You’ll find the oil pump on the burner’s left side which is connected to the flexible oil line. Once done, simply locate the 3 inches long hexagonal stem protruding from the pump and with a small threaded plug screwed into the end. Unscrew the plug in just half a turn ( 180 degrees) with a 4mm Allen Key. At this stage oil will be released, do ensure there’s a cloth or rag underneath the plug to grab the oil freed.

• Press the lockout button

This is the next and final step. However it’s also crucial to note that the burner fan will run for about 12 seconds and discharge some oil from the loosened plug which you can grab with a cloth or rag. Immediately you hear a buzzing sound, use the Allen key to tighten the plug. If enough air has been bled, the system will fire. But if not, then you’ll have to repeat the process again.

The Oil Firing Technical Association or OFTEC operate a competent persons scheme to certify installers. It’s always recommended to use an installer with this certification as it proves they have the training and expertise to properly install your boiler and give you realistic advice on the efficiency of your system. Also, OFTEC registered installers offer Workmanship Warranties to protect you if there are any problems after installation.