Find a Heating Engineer you can trust in Isle Of Skye.

When it comes to gas boilers, this is one of the most frequent questions that always pops up and for a good reason. When you invest a considerable amount of money to acquire and install a gas boiler in your home or property, it’s only reasonable not only to expect the boiler to warm up your home efficiently, but also to do so for a long period of time. If you’ve just bought or about to get a new gas boiler, it’s likely you won’t have to worry about getting a replacement for a lengthy period of time. Several gas boilers will last for anywhere between 10 to 15 years on the average. However in the event whereby you have an existing one that’s fast approaching the end of it’s useful life, then you should know the time go get a new gas boiler is just around the corner, and the earlier you make the purchase, the better (to avoid any surprise breakdowns that’ll leave your home super uncomfortable).

Just like any other home appliance, it’s a fact that an older gas boiler ( especially those that have been installed over a decade ago) are significantly less efficient that the new modern ones. When the older versions were manufactured is a completely different time to now as both technology and climate concerns are wide apart. So when your existing boiler is approaching the end of it’s useful life, it’ll be wise to start saving up to cover the cost of getting a new one. However, if it’s only about 5 years ago your boiler was installed, it’s highly likely to still be very efficient.

How Do You Bleed An Oil Boiler?

Bleeding air between the oil supply and an oil fired boiler’s burner is a process that’s often required when the system has run out of oil and the burner has stopped working. Upon refilling the oil tank, the air that has been trapped within the oil pipe when empty has to be freed to ensure that the oil reaches the burner and allows it to start again. So how do you go about the process?

First and foremost, it must be noted that it’s always better to be on the look out for the amount of oil in your fuel tank and get it refilled before it runs out. However, if it does run out, you can take the following steps:

• Identify the burner

The burner is a red plastic cover and it’s usually positioned on the bottom part of the boiler (mostly inside the boiler casing). Once identified, inspect it to see if the lockout button is lit red. If yes, simply unscrew and detach the burner’s red case using a flat head screwdriver.

• Identify the oil pump

You’ll find the oil pump on the burner’s left side which is connected to the flexible oil line. Once done, simply locate the 3 inches long hexagonal stem protruding from the pump and with a small threaded plug screwed into the end. Unscrew the plug in just half a turn ( 180 degrees) with a 4mm Allen Key. At this stage oil will be released, do ensure there’s a cloth or rag underneath the plug to grab the oil freed.

• Press the lockout button

This is the next and final step. However it’s also crucial to note that the burner fan will run for about 12 seconds and discharge some oil from the loosened plug which you can grab with a cloth or rag. Immediately you hear a buzzing sound, use the Allen key to tighten the plug. If enough air has been bled, the system will fire. But if not, then you’ll have to repeat the process again.

When your boiler is being replaced you won’t have hot water or central heating. If you don’t mind this you can stay in your home, and use portable electric heaters if needed. Most installers undertake a power flush before installing a new boiler now and this can cause muck and debris from the pipework, so you may wish to get out of the way while this is happening!

How Much Is A Boiler Service?

A broken boiler can be a huge pain and even more so if it occurs during the winter months. A cold house and cold shower is not a situation to be handled with levity especially when there are older people or more vulnerable members in the house. To ensure your boiler keeps functioning the way it should for a lengthy period of time, it’s crucial to ensure that you have your boiler serviced on a yearly basis. But while the summer or warmer months happen to be the most cost effective time to have the boiler servicing done, doing it during the depths of winter can go a long way to ensure that you and your loved ones get through the cold without any unwanted occurrence or boiler issues.

Generally, to have your boiler serviced will cost anything within the range of £80 to about £120, but at times, this can even be more depending on a plethora of factors. The servicing cost will be based on the particular company you choose, the type of boiler you possess, as well as your location in the UK. For instance, if you happen to live in London where demands are higher than the other regions, then you’ll most likely have to pay more money to have your boiler serviced than other homeowners facing similar issues but staying in the other lower demand regions.

Asides from hiring a professional to service your boiler on an annual basis, you should also try to help maintain its efficiency and health in between those services. This will not be a substitute to the regular servicing or even make the servicing a lot simpler, but will surely help keep it at a maximum efficiency while also keeping the cost of your heating bills down.

Can You Get Oiled Fired Combi Boilers?

Absolutely! Oil fired combi boilers are not only a super cool alternative to gas heating, but also offer a cost-efficient means of heating your home. And this is best enjoyed especially if you’re one of the estimated 4 million houses that are not connected to the gas network.

Oil fired combi boiler enables you store fuel close to your property and fill it as required. There many A rated model options available in the market with the modern oil fired combi boilers confirmed to be up to 95% efficient. As a result of their multiple advantages over alternative heating systems, the oil fired combi boiler is expected to increase significantly in the UK. Here are some of the advantages of adding the system to your property.

• Oil fired combi boiler heats up water on demand while also saving a lot of fuel and being super energy efficient.

• Since oil needs more fuel than gas, a great return would be derived from every unit of energy.

• When compared with the other types of boilers, oil fired combi boilers have a considerably lower operating cost.

• A new oil fired boiler typically has a 92% to 95 % efficiency, which is significantly better than the 60% to 70% in older systems.

If you have an idea of how to operate the gas-powered alternative, then operating an oil fired combi boiler shouldn’t be an issue. In a similar way to the alternative, the boiler simply delivers the central heating through the radiators and hot water via your household’s taps.

However, the major difference between the two is the fact that the oil fired boiler needs a regular supply of oil, which is stored in a tank. The hot water supplied by the system is instant as it is connected to the water mains supply.

If you’re thinking about getting a new gas boiler for your home or property, then you might also be wondering how much it’ll cost you so you can set a budget and start planning. As simple as this question sounds, it’s actually very tricky to provide a simple and short answer as the costs of installing a new gas boiler alone varies greatly based on the parts needed, the amount of work required, your location, their availability as well as the company you hire for the project.

When it comes to purchasing a new gas boiler the price you’re expected to pay also depends on multiple influencing factors such as the type, brand as well as your most preferred gas boiler model. However, one thing you should have in mind is the fact that your gas boiler is right at the heart of your home or property and can be a complicated piece of machinery. As a result, you wouldn’t expect gas boilers to come cheap. Generally, it’s going to cost within the range of £500 to about £2,500 to get a new gas boiler. Therefore, it’s always advisable to obtain all necessary details and facts before you decide to purchase a replacement gas boiler.

This price range may seem too high as it’s usually a turn off for most homeowners. However, it’s worth noting that gas boiler replacement costs and gas boiler installation costs are, more often than not, compensated by the saving you’ll make off your utility bills - all thanks to the new and more energy efficient boiler you just installed in your home. And even more importantly, when it has been estimated that roughly half of the amount spent on energy on an annual basis depends on your boiler.

How To Get A Gas Fireplace Installed

A gas fireplace is one of the most popular means of adding warmth to homes which so many homeowners have now come to terms with, especially with natural gas prices being fairly low for an extended period of time. Properly installed gas fireplaces are not only capable of adding a much needed ambiance and warmth to your home, but also significantly more efficient than the traditional wood-burning fireplaces which mostly produces less heat from the large amount of drafts they consume. Meanwhile a good gas powered fireplace with a properly functioning blower, is very close to being as efficient as a furnace when warming up a room. What’s more? Gas fireplaces also possess a great visual appeal and are also very practical especially when they feature realistic ceramic logs as well as good gas burners.

Installing a gas fireplace by yourself is definitely up there as one of the most advanced DIY tasks you can attempt to try. If you lack proper training and experience, it’s advisable you leave the task to a reliable professional that’ll guarantee the best results while also ensuring costly errors are avoided. This guide will, however, put you in the right direction.

• Construct wall recess to accept the fireplace.

• Punch a hole through the exterior wall of the house to fit in stovepipe thimble.

• Fix a small part of the stovepipe to the exhaust port in the fireplace’s rear.

• Use construction adhesives on the wall around the fireplace opening’s sides and top.

• Apply granite slabs into the adhesive around the opening of the fireplace.

• Put the fireplace in position and ensure the stovepipe goes outdoors through the thimble.

• Use a termination hood to seal the exhaust pipe’s exterior.

• Employ the services of a professional plumber to connect the gas to the fireplace.

• Fit the removable front

• Test the functionality of the fireplace.

In recent times, home and property owners are constantly looking for ways in which to enhance both energy efficiency and sustainability especially as the world draws closer and closer to energy-efficient technology. The Nest thermostat is a great example of this fact as its designed in such a way to save energy while also cutting heating and cooling costs. And an interesting fact is, you’re not limited to using just a single Nest thermostat in your home as multiple of the device can successfully run together to maintain a consistent level of temperature monitoring as well as energy efficiency. What’s more? You can add up to 20 Nest thermostat and 18 temperature sensors in a home.

It’s very unlikely that you’re going to need this many thermostats in your home, but if you’d like to add a second the process is quite straightforward. However, we’d recommend you employ the services of a seasoned professional especially if you lack the required training or experience to pull this off to save yourself some time and money.

To get started, simply download the associated Nest app to add Nest devices. Now let’s have a look at the processes involved in adding a second Nest thermostat to your home.

• Open the app.

• Go to the top left corner of the main screen and click on the menu button.

• Pick the location or home you’re adding the device to.

• Go to the top right corner and select the “settings.

• Once done, then click on the Add Product “Plus button.

Upon a successful addition of the second thermostat, the app will guide you through the initial set up steps. Google also offers a very helpful guide if you’re unfamiliar with the initial configuration.