Find a Heating Engineer you can trust in Sevenoaks.

Your LPG storage tank should have a gauge that shows you how much fuel it has in it. Most LPG suppliers suggest that you arrange a fuel delivery when the level in your tank gets down to about 20%. Make regular checks, particularly in the winter when you will use more, so you know when levels are low.

If your boiler is leaking, there are some checks that you can do yourself. However, you should never attempt to repair your boiler yourself – only a Gas Safe-registered engineer should conduct repairs.

There are 3 main reasons why your boiler might be leaking: there’s a pressure valve fault, a temperature valve leak or corrosion in the system. An engineer will be able to spot the problem quickly, but in the meantime there are a few things you can do:

Check the pipe fittings

If your boiler is leaking water around the pipe fittings, it could be an installation fault and you should get in touch with the engineer that fitted it. You can check the pipe fittings by drying the area then waiting to see if the water appears again. If it does, you may be able to do a ¼ turn of the pipe to stop it. However, you should still call the engineer that installed it to ask them to check the PTFE tape on the inside.

Inspect the seals

Over time, the rubber seals on a boiler can start to perish, so if you have an old boiler this could be the source of your leak. If you have a new boiler, it could be caused by your boiler running over pressure.

Heat exchanger corrosion

Unfortunately, if a boiler engineer discovers that the boiler is leaking water from the heat exchanger, this is the end of the road for your system. The heat exchanger is the most expensive part of your boiler, so it makes more financial sense to replace your boiler with a newer, more efficient model rather than try to replace it.

How Much Is A Boiler Service?

A broken boiler can be a huge pain and even more so if it occurs during the winter months. A cold house and cold shower is not a situation to be handled with levity especially when there are older people or more vulnerable members in the house. To ensure your boiler keeps functioning the way it should for a lengthy period of time, it’s crucial to ensure that you have your boiler serviced on a yearly basis. But while the summer or warmer months happen to be the most cost effective time to have the boiler servicing done, doing it during the depths of winter can go a long way to ensure that you and your loved ones get through the cold without any unwanted occurrence or boiler issues.

Generally, to have your boiler serviced will cost anything within the range of £80 to about £120, but at times, this can even be more depending on a plethora of factors. The servicing cost will be based on the particular company you choose, the type of boiler you possess, as well as your location in the UK. For instance, if you happen to live in London where demands are higher than the other regions, then you’ll most likely have to pay more money to have your boiler serviced than other homeowners facing similar issues but staying in the other lower demand regions.

Asides from hiring a professional to service your boiler on an annual basis, you should also try to help maintain its efficiency and health in between those services. This will not be a substitute to the regular servicing or even make the servicing a lot simpler, but will surely help keep it at a maximum efficiency while also keeping the cost of your heating bills down.

If you choose to install an LPG boiler, you’ll need to find an LPG supplier. They’ll deliver fuel to you every time your storage tank runs low. You can even rent a storage tank from them if you don’t want to buy one. Make sure you know who your local suppliers are and where they are based.

How Does Electric Central Heating Work?

An electric central heating works to provide a number of benefits for you. These benefits include the following:

lSpace Heating

• The storage heaters work during the night to store electricity which would be used to heat up the heat retaining bricks. This, in turn, will release this energy throughout the day to warm up the room.

• There are also electric radiators which works to deliver on-demand heat and as a result, economy tariffs are totally avoided. It will generate heat by itself rather than storing it and with the controls, you can easily determine the amount of heat to be released when you require it.

• There is the wet electric system options as well which comes with water filled radiators. This operates in a similar way to normal radiators, however, it makes use of electricity to heat up the water.

lWater Heating

• An electric boiler operates in a very similar manner to other boiler types, just that it makes use of electricity as its fuel. Here, the water is warmed by a heating element and the water is later moved to several radiator throughout the house by a pump. These electric boiler types earns you tariff savings as you’ll be able to heat water at night.

• Heat pumps geothermal or air source, redistributes heat instead of creating it. Heat pumps are powered by electricity and it works by absorbing heat either from the air or ground which it then channels it through a pump. This can then be incorporated in heating either water or a room.

• A dedicated immersion heater is another water heating option. Here, the heating element is positioned inside a hot water cylinder. In a similar fashion to a kettle, the element heats the nearby water. Immersion heater can act either as a backup or your main heating element.

A boiler is simply the most important part of a central heating system as it generates the heat that warms up the home or property. Basically, the appliance or small furnace makes use of gas, LPG or oil in order to fuel its operation. However in the UK, most boilers are usually fuelled by natural gas which is supplied automatically from the national gas grid. And depending on how it operates, there are various types of boilers.

Typically, a gas central heating boiler will have multiple pipes entering from underneath. While one pipe supplies the boiler with gas from the mains gas supply, another pipe allows cold water to enter the boiler to be heated, the last pipe then enables hot water to exit the boiler so it can be distributed around the home.

✓ There are fuel jets and heat exchangers inside the boiler. When the heating is turned on, a valve is opened to allow the mains supply gas to enter a sealed combustion chamber in the boiler. There are multiple little valves which permit the entry of the gas before being ignited by an electric ignition switch. These jets heat a metal component in the boiler known as a heat exchanger which works to transfer the heat to the cold water pipe and heat up the water.

✓ Once the water has been heated to the target temperature, it’s then pumped through a circuit of pipe which runs around your home by an electric pump.

✓ The heated water enter each radiator, is then transmitted via a closed loop and radiates heat into each room.

✓ Once done travelling through all radiators, the water then returns to the boiler at which it must have been cooled. Therefore, the boiler will have to reheat following the same process before circulating. The water can only be drained by a professional Gas Safe engineer

The Hive thermostat stand is relatively easy to install, however if you lack the necessary training or experience, this is a task you might want to leave to a professional to guarantee the best result while also saving you money and time. This guide will give you a good insight into the Hive thermostat installation process.

The installation of a Hive thermostat does require it to be connected to your home boiler. For this reason we always recommend you get a professional to install it. However once install the Hive Smart Thermostat is very easy to operate and move the controller around your home. To get started, you can follow these steps:

• Press the lever at the lower side of the thermostat and pull away from the front to detach the back plate of your device.

• Once done, simply hang the thermostat on the stand back plate and ensure it holds firmly in place

When it comes to Hive thermostat installation, you might also want to consider the positioning of the device in such a way to heat your home even more efficiently as its designed to be very sensitive to temperature. To identify the best spot for your Hive thermostat, let’s take a look at some of the dos and don’ts.

A Few Dos:

• Do maintain the position of your Hive Thermostat to keep a stable connection with the receive and Hive Hub.

• Do ensure that the position chosen is the centre of your home or a frequently used room.

• Do place the thermostat about 1 to 1.5 metres from floor.

• Do ensure that your thermostat is in a close proximity with the hub and receiver for a better functionality.

A Few Don’ts:

• Don’t place your Hive thermostat stand close to radiators, direct sunlight or other heat sources,

• Don’t position your device near or at places that can expoerience a sudden change in temperature such as the front or back door.

• Don’t leave your thermostat too close to curtains or ornaments.

Ad hoc visits from your engineer to fix small issues with your heating system may actually seem cheaper and a lot more affordable, however when a boiler is ripe enough for a change these small issues are always never ending. Over some period of time, these small issues will inevitably get worse and the idea of “mend and make do will be an absolutely false economy. The best course of action in this sort of event is to find a replacement boiler to install as soon as possible. In this article, we’re going to give you some hints that’ll show you when your boiler needs to be replaced. Now let’s take a look!

✓ Insufficient hot water. Here, you’ll have to check the size of your hot water cylinder. It’s crucial to make sure that your boiler is rightly sized to power your heating as well as hot water circuit in line with your demands. You should always seek the advice of a heating expert who can recommend whether to fix or replace the boiler.

✓ Strange noises. It’s normal for components of the boiler to become worn or damaged over time. Replacing the particular component that’s causing the knocking or rattling may seem cost effective at first but more often than not, the noises usually signal a bigger issue which is likely to build up over time. Hence, it’ll be a lot more logical to replace the boiler itself.

✓ Regular repair of your boiler. It’s essential to have your heating system serviced by a Gas Safe engineer on an annual basis. However, when you have to call them more often than once a year for your yearly maintenance, it may be a wise decision to consider getting a replacement.

✓ Other events whereby you may need a new boiler includes when you can’t get the right temperature in your room, when the radiators don’t heat up as they should, when your boiler leaks and if your boiler still has a pilot light.