Find a Heating Engineer you can trust in London County.

Re-pressurising your boiler means that you allow more water to enter system via the filling loop. It can be easy to re-pressurise your boiler yourself. Always check your manual, but there are some simple steps you can take to restore pressure to your boiler:

1. Switch off your boiler and let it cool completely
2. Make sure both ends of your filling loop are attached
3. Open both valves to allow cold water into the system – you’ll hear it start to move
4. Look out for your pressure gauge to show 1.5 bar
5. Close both valves
6. Switch your boiler back on
7. Undo both ends of your filling loop and remove it. Remember some water might come out, so be ready to catch some spillage!

No. You must never repair your own boiler – only a Gas Safe-registered engineer can do any work on your boiler. You can do simple DIY tasks to repressurise your boiler or stop a leak, but if you have to remove the outer casing of the boiler or touch the flue then you must get a qualified boiler engineer to take a look at your central heating system.

How Much Does A Boiler Repair Cost?

An annual service for your boiler might not seem important and may be easy to postpone to another day, but when it happens to breakdown due to lack of adequate attention, this can be quite painful and also costly.

Before you start thinking about the cost of repairing your boiler, the first thing you’ll need to confirm is whether or not your boiler is still covered by the manufacturer’s warranty. You’d be amazed some warranties can last for as long as 12 years, if yours is still on then you can save yourself a huge amount of of money on your boiler repair. As a result, it’s always crucial to keep the details of your warranty somewhere safe, so you can read them from time to time. You never can tell when the rainy day will come!

Most boiler warranties will require your to get your boiler serviced on an annual basis by a licensed and qualified technician. The cost of an annual boiler service is affected by the time of the year you wish to get it done. When boilers are less useful during the summer months, an annual service is usually relatively cheap when compared to the cold months. Around this period, a boiler service will normally cost within the range of £100 to £150, however for a more accurate quote it’s advisable to contact a couple of professionals and compare their quotes.

The cost of getting a boiler repaired will be affected by a couple of factors including your boiler’s make, the age of the boiler as well as your location and how urgent you need it done. If you have a dead boiler, the cost will typically range from £96 to £348 and a boiler displaying a fault code will cost within the range of £90 to £275. Generally, repairing a boiler will cost within the range of £90 to £400 based on the several factors stated above.

If you’re thinking about getting a new combi boiler, you may be wondering just how much it’s going to cost so as to start making preparations as soon as possible. However, providing a precise cost for the acquisition and installation of a new combi boiler is simply impossible as combi boiler prices vary greatly in price - usually ranging between £1500 to about £3500 based on the brand of the combi boiler, the insurance or warranty, installation, your location as well as the size and power of the appliance. Due to the fact that combi boilers are compact units which doesn’t need a hot water cylinder or a cold water tank to produce heating and hot water for homes, it’s a very popular type of boiler that’s frequently used especially in the UK.

Combi boilers are also widely known to be the most energy efficient type of boiler because they are able to provide an instant supply of hot water anytime you turn on a tap. Combi boilers particularly perfect for flats and houses where space is limited as they have the ability to deliver instant heating and hot water without requiring any extra parts or components.

In the event whereby you’re about to choose a combi boiler for your home or property, it’s always advisable to compare models as well as prices from only the most reliable and sought after brands across the globe. Depending on the manufacturer, the overall quality of the boilers as well as their prices can differ. However, regardless of your budget, you’ll discover there are a plethora of combi boilers available in the market that’ll also suit your taste.

Smart controls such as Hive are the next generation technology with more and more people now converting their houses into smart homes to control multiple devices in the homes remotely. Smart technology can be incorporated with several household devices such as security, lighting, entertainment and more. But what if there’s an oil boiler installed in your home, can you still connect your Hive with the your heating? Well, simply read on to find out.

The answer to this question is yes, most oil boilers are compatible with Hive and can substitute for either an existing conventional programmer or thermostat. The smart technology works to help derive more benefits from your heating system and they usually come with apps which can be used to control your home’s heating from anywhere with just your mobile device. Hive, however, cannot work to replace the functions of smart oil boiler heating controls to modulate your heating as they only work on an on or off basis. To make use of the modulating technology in an oil boiler, the cost of manufacture would be considerably higher while offering little advantage in efficiency for the home or property owner. Ultimately, this implies that you can’t incorporate smart technology to control the output in a similar way as a gas boiler, but there are still some ways to utilize smart technology with your oil boiler in such a way to boost your efficiency and lessen the energy bills.

Do you want to use your Hive with your home’s oil boiler? We’d advise you get in touch with an OFTEC qualified engineer if you wish to install Hive Active Heating on your oil boiler, as British Gas engineer do not offer this service.

If you’re looking to acquire smart thermostats in your home, but wondering about its money saving qualities, then this is for you! Not only do smart thermostats add new impressive features to your home, but it can also save you both energy and money. According to many reports using a programmable thermostat can save you between the range of £130 to £150 on an annual basis. Now think about using a smart thermostat that makes it a lot more easier for you.

Wondering how smart thermostat save money? Simply set your smart thermostat one or two degrees lower or higher than the usual number. Once done, you’re likely to notice 1% to 3% reduction in your energy bills. And if you want even more, you simply increase the percentage to about 10 degrees to 15 degrees to cover the period you spend at work and watch as you save up to 10 percent of your energy bills.

Generally, a smart thermostats will save you money in two major ways. These includes:

• They Do All The Thinking For You

The smart thermostat watches your behaviour and study the time you’re at home and when you’re not as well as your preferred temperature at particular times in a day, and that’s why they are termed as “smart. they’ll automatically adjust the settings to ensure you get home to a perfect temperature.

• They Keep Tabs On Your Usage

You can always count on a two way communicating smart thermostat to watch your usage while also collecting the data and sharing it with you. It informs you of your energy usage rate as well as the estimated amount. Once you’ve been notified, you can manual adjustment or leave it to the thermostat to help manage your energy.

How Long Does A Gas Safety Certificate Last?

As a result of faulty installation and irregular maintenance of gas appliances and chimneys, a lot of people have been met with an untimely death caused by the toxic gas - carbon monoxide. This is a gas that’s completely odourless, colourless and tasteless - meaning you can’t identify one of its in the environment. But what you should know is, if you stay in an environment filled with carbon monoxide, you’d probably be dead within a couple of hours. Consequently as a landlord, you must do what’s best to ensure the safety of all your tenants by making sure that all your gas appliances and chimneys are subjected to annual check by an approved Gas Safe engineer as required by the law.

Wondering how long a Gas Safety Check will take? The safety of your gas is guaranteed by carrying out regular examinations. Whether or not you possess a gas alarm, it’s still vital to conduct regular gas safe checks to make sure your home is safe. A typical gas safe check would last between 30 to 60 minutes for a normal domestic property. However, in the situations whereby a need for repair arises, it may take longer time to complete. Other factors that can also affect the timing includes includes both the size and location of your property.

So how long does a gas safety certificate last? The simple answer to this question is 12 months. If you own a rental property in the UK, it’s up to you to ensure all your gas appliances and chimney is check after every 12 months to obtain a Gas Safety Certificate which you should hand out a copy to all tenants living in your property. However, if you don’t own the property, you can inform your landlord to get one as soon as possible while also providing a carbon monoxide alarm.

How To Install A Gas Cooktop In An Island

Are you thinking about installing a gas cooktop in your kitchen island? If yes, then you must know that there are clearance requirements that must be met (before you proceed) between the cut out and the countertop’s edge. Basically, there are incremental requirements for island installation due to the fact that it does not make an assumption that the product is going to be fitted against a rear wall that acts to protect the back of the unit. As a result, while doing an island install we must put the safety of the product into consideration much more that we do a standard install. What’s more? This island clearance requirement develops from a third-party agency and is a standard with all brands. So how do you install a gas cooktop in an island having the aforementioned requirements in mind?

• Use a foil tape to line the inside edges of the cut out. The function of this is to prevent heat damage as well as countertop’s discolouration. Put the cooktop top on a secured surface.

• Identify the pipe coming out of the cooktop’s side or bottom and brush onto the threads of the manifold entrance.

• Pass the pressure regulator onto the entrance of the manifold and make use of a wrench to tighten it.

• Brush the pipe joint compound onto one of the flare union adaptor’s threads and pass it into the regulator’s open end. Make it slightly tight with a full turn of the wrench.

• Connect the flare union adaptor’s open end with the flexible appliance connector hose, upon brushing on pipe joint compound.

• Put foam tape on the cooktop underside’s edges, if your cooktop comes with a glass burner plate.

• Turn the cooktop to set it into the cutout.

• Apply pipe-joint compound onto the flare union adaptor left and secure it firmly into the gas shutout valve.

• Connect the flexible hose connector’s free end with the flare union adaptor.