Find a Heating Engineer you can trust in Ruislip.

Modern oil boilers do not require a lot of maintenance. OFTEC recommends that oil boilers are serviced and inspected every year. This keeps them running as efficiently as possible and will ensure any issues with your boiler are identified before they cause bigger problems. This servicing is also vital because of the increased risk of carbon monoxide leaking from a poorly maintained boiler.

Biomass boilers can be designed to work with other kinds of heating. The most common of these is solar thermal. This is a popular renewable energy pairing. Solar thermal heating will meet your hot water needs during the summer while a biomass boiler can operate as a backup during the winter when solar thermal panels do not perform as well.

How Do You Bleed An Oil Boiler?

Bleeding air between the oil supply and an oil fired boiler’s burner is a process that’s often required when the system has run out of oil and the burner has stopped working. Upon refilling the oil tank, the air that has been trapped within the oil pipe when empty has to be freed to ensure that the oil reaches the burner and allows it to start again. So how do you go about the process?

First and foremost, it must be noted that it’s always better to be on the look out for the amount of oil in your fuel tank and get it refilled before it runs out. However, if it does run out, you can take the following steps:

• Identify the burner

The burner is a red plastic cover and it’s usually positioned on the bottom part of the boiler (mostly inside the boiler casing). Once identified, inspect it to see if the lockout button is lit red. If yes, simply unscrew and detach the burner’s red case using a flat head screwdriver.

• Identify the oil pump

You’ll find the oil pump on the burner’s left side which is connected to the flexible oil line. Once done, simply locate the 3 inches long hexagonal stem protruding from the pump and with a small threaded plug screwed into the end. Unscrew the plug in just half a turn ( 180 degrees) with a 4mm Allen Key. At this stage oil will be released, do ensure there’s a cloth or rag underneath the plug to grab the oil freed.

• Press the lockout button

This is the next and final step. However it’s also crucial to note that the burner fan will run for about 12 seconds and discharge some oil from the loosened plug which you can grab with a cloth or rag. Immediately you hear a buzzing sound, use the Allen key to tighten the plug. If enough air has been bled, the system will fire. But if not, then you’ll have to repeat the process again.

What Size Of Oil Boiler Do I Need?

When it comes to oil boilers, there are three main types - the combi, system and conventional. Within these types, you’d discover there happens to be a wide range of sizes to choose from. First and foremost, we must note that the size has to do with the amount of energy they offer to your heating and hot water system rather than the physical dimensions.

The rule of thumb is, the larger your house (which implies the more hot taps, radiators and showers), the more powerful (bigger) the oil boiler you’d require. For instance, a four-bedroom apartment with three showers occupied by a family of four will definitely need a more powerful boiler than a a bungalow featuring a single occupant.

It is, however, important to also note that it’s not all about going for the biggest oil boiler. If you decide to choose an oil boiler with a much bigger capacity that needed, not only will you be wasting money on the initial purchase as well as installation, but also lose money operating it. And in a converse scenario, if you go for the cheaper and lower-powered oil boiler in an attempt to save up some money, you’re most likely to end up with tepid radiators while also frequently running out of hot water. Hence, the importance of determining the appropriate size of boiler for your particular household before purchase.

To determine the appropriate size, determining the number of bathrooms, radiators as well as the total number of people living in the property would be a step in the right direction.

Numbers of Radiators Combi System Boiler Regular

Up to 10 24 to 27kW 9 to 18kW 9 to 18kW

10 to 15 28 to 34kW 18 to 26kW 18 to 26kW

15 to 20 35 to 42kW 27 to 40kW 27 to 40kW

First and foremost, the purpose of a landlord insurance is simple and pretty straightforward. It protects against risks associated with your rental property as well as activity. Most policies start out with building insurance as well as property owners’ liability insurance but you’re absolutely free to include several other covers. These covers can include tenant default or accidental damage, loss of rent and more depending on your needs. It’s important to note that varying types of landlord insurance provides coverage for different sorts of risks. For instance, building insurance provides coverage for the cost of repairing or rebuilding your property, while contents insurance provides coverage for contents if they’re damaged or stolen. However, the question is, does landlord insurance cover boiler? In this post, we’re going to shed more light into this to help you make informed decisions moving forward. Let’s take a look!

The short and simple answer to this question is yes, landlord insurance can definitely cover boiler break down! However, this is usually possible only if you select this option when you purchase your landlord insurance policy. With some boiler cover providers, you’ll have to include a home emergency cover to your landlord insurance so as to cover any form of boiler break down. Once this is done, if the boiler in your rental property starts to malfunction or stops functioning, a Gas Safe registered engineer would be sent to your premises to help out with the situation. With this, the repairing cost of your heating system would be covered by the insurance excluding any excess and up to the limit of your policy.

Condensing boilers are the in-thing when it comes to modern heating systems in UK homes and across the globe for a good reason. This is primarily due to the fact that condensing boilers happens to be highly efficient as it enables the fuel you’re burning to heat up your home go a lot further. Having a new high efficiency condensing boiler rather than an old G-rated non condensing boiler will not only enhance your heating controls, but also save you a lot of money annually. In this article, we’re going to take you through the basics of a condensing boiler. Let’s take a closer look!

If you’re interested in getting a greener and more efficient boiler, you simply can’t afford to look beyond a high efficiency condensing boiler. This is purely due to the fact that these condensing boilers happens to make a better use of the heat they’re able to produce from burning fuels like oil or gas ( in other words, they require less heat from the burner, which makes them a lot more efficient).

So how does a condensing boiler work? Unlike a non-condensing heat-nly boiler, some heat will be wasted in form of hot gases which are released from the flue. Meanwhile a condensing boiler captures some of the heat from these gases and puts them to use for heating up water that’s coming back from your central heating system. As a result, it requires just a minimal heat from the burner which make the boiler more efficient.

You should take note that all new modern boilers are condensing boilers. Therefore if you’re planning to replace an old boiler with a new one, you’ll definitely be buying a new condensing boiler and benefit from all the efficiency and savings that comes with it.

How Much Does It Cost To Service An Oil Boiler?

With several homes in the UK using gas central heating, about 6 percent of households in the United Kingdom makes use of oil for their heating needs. If you’re one of those homeowners with an oil boiler, then you should know that servicing your oil boiler is a compulsory activity which should be done regularly in order to ensure the safety of your home, boost the efficiency of the boiler while also help you save money as it ensures you do not incur the potentially expensive repairs or even having to purchase a replacement boiler. If you service your oil boiler every year, you can be rest assured that you’ll continue to derive maximum benefits from your prized heating system for a long period of time. So exactly how much will you have to pay to service your oil boiler?

The service cost of an oil boiler is influenced by a wide range of factors which includes the location. However, the average cost of servicing an oil boiler in the UK is between £65 to £90, but depending on the location as well as other influencing factors, this price might be higher or lower.

Due to the higher cost of living and high demands at places such as London and the south east of the UK, you can discover that the cost of servicing your oil boiler can jump to as high as £160 to £190. In other regions, you can also find the oil boiler service cost to be as low as £50 to £60. What’s more? In the same locations, you can also discover varying prices which depends on the available services. Furthermore, in areas where there’s a lower competition from several engineers, the prices may also be higher.

If you’re interested in deriving maximum benefits from your central heating system while also being a tech-enthusiast, a smart thermostat is just the perfect option as it allows you to control both your boiler and heating system via your mobile device. It also offers a plethora of features which enables you to heat your home more efficiently while also cutting your energy bills. Here, we’ll be taking a deeper look at the Tado smart thermostat (a user friendly smart thermostat with multiple impressive features such as a great design, self learning and LED interface).

A Tado smart thermostat is a relatively small piece of kit which is perfect for tech-lovers looking to get a first experience of the smart thermostats’ world. Although the appliance might feature just a basic design with a bit less advanced features in comparison with other thermostats like Hive, Nest and more, it however, still comes with some fantastic features which you can’t afford to miss out on. These includes geofencing, Smartphone or tablet control as well as heat scheduling. As you would have expected with any good smart thermostat, the ability to remotely control your heating is a top priority for several smart thermostats’ owners and Tado offers you this and more. Therefore, no more worries during the Winter months and wishing your home should be warm and perfect for your return. Aside this, a Tado smart thermostat also goes a long way to ensure efficient energy use and as a result, reducing the money paid on energy bills.

Overall, Tado is a nicely designed smart thermostat which is relatively easy to use and a perfect option for homeowners interested in having a taste of the world of smart thermostats or looking to replace their existing device.