Find a Heating Engineer you can trust in Southall.

How Do You Bleed An Oil Boiler?

Bleeding air between the oil supply and an oil fired boiler’s burner is a process that’s often required when the system has run out of oil and the burner has stopped working. Upon refilling the oil tank, the air that has been trapped within the oil pipe when empty has to be freed to ensure that the oil reaches the burner and allows it to start again. So how do you go about the process?

First and foremost, it must be noted that it’s always better to be on the look out for the amount of oil in your fuel tank and get it refilled before it runs out. However, if it does run out, you can take the following steps:

• Identify the burner

The burner is a red plastic cover and it’s usually positioned on the bottom part of the boiler (mostly inside the boiler casing). Once identified, inspect it to see if the lockout button is lit red. If yes, simply unscrew and detach the burner’s red case using a flat head screwdriver.

• Identify the oil pump

You’ll find the oil pump on the burner’s left side which is connected to the flexible oil line. Once done, simply locate the 3 inches long hexagonal stem protruding from the pump and with a small threaded plug screwed into the end. Unscrew the plug in just half a turn ( 180 degrees) with a 4mm Allen Key. At this stage oil will be released, do ensure there’s a cloth or rag underneath the plug to grab the oil freed.

• Press the lockout button

This is the next and final step. However it’s also crucial to note that the burner fan will run for about 12 seconds and discharge some oil from the loosened plug which you can grab with a cloth or rag. Immediately you hear a buzzing sound, use the Allen key to tighten the plug. If enough air has been bled, the system will fire. But if not, then you’ll have to repeat the process again.

How Does Electric Central Heating Work?

An electric central heating works to provide a number of benefits for you. These benefits include the following:

lSpace Heating

• The storage heaters work during the night to store electricity which would be used to heat up the heat retaining bricks. This, in turn, will release this energy throughout the day to warm up the room.

• There are also electric radiators which works to deliver on-demand heat and as a result, economy tariffs are totally avoided. It will generate heat by itself rather than storing it and with the controls, you can easily determine the amount of heat to be released when you require it.

• There is the wet electric system options as well which comes with water filled radiators. This operates in a similar way to normal radiators, however, it makes use of electricity to heat up the water.

lWater Heating

• An electric boiler operates in a very similar manner to other boiler types, just that it makes use of electricity as its fuel. Here, the water is warmed by a heating element and the water is later moved to several radiator throughout the house by a pump. These electric boiler types earns you tariff savings as you’ll be able to heat water at night.

• Heat pumps geothermal or air source, redistributes heat instead of creating it. Heat pumps are powered by electricity and it works by absorbing heat either from the air or ground which it then channels it through a pump. This can then be incorporated in heating either water or a room.

• A dedicated immersion heater is another water heating option. Here, the heating element is positioned inside a hot water cylinder. In a similar fashion to a kettle, the element heats the nearby water. Immersion heater can act either as a backup or your main heating element.

If your property is not connected to a gas main, oil boilers are a great alternative to gas boilers and more efficient than LPG alternatives. They can also be paired well with renewable sources. However, if your property is connected to the gas mains, there is generally no reason to switch to an oil boiler, as you will need to have oil delivered to an extra storage tank.

Biomass boilers do require some maintenance. Many manufacturers recommend servicing twice a year, although this is often included in the installation cost. Many systems have automatic fuel loading that removes the need to manually load fuel. You will need to remove the ash from the boiler, but this is as easy as emptying a vacuum cleaner.

If your boiler is leaking, there are some checks that you can do yourself. However, you should never attempt to repair your boiler yourself – only a Gas Safe-registered engineer should conduct repairs.

There are 3 main reasons why your boiler might be leaking: there’s a pressure valve fault, a temperature valve leak or corrosion in the system. An engineer will be able to spot the problem quickly, but in the meantime there are a few things you can do:

Check the pipe fittings

If your boiler is leaking water around the pipe fittings, it could be an installation fault and you should get in touch with the engineer that fitted it. You can check the pipe fittings by drying the area then waiting to see if the water appears again. If it does, you may be able to do a ¼ turn of the pipe to stop it. However, you should still call the engineer that installed it to ask them to check the PTFE tape on the inside.

Inspect the seals

Over time, the rubber seals on a boiler can start to perish, so if you have an old boiler this could be the source of your leak. If you have a new boiler, it could be caused by your boiler running over pressure.

Heat exchanger corrosion

Unfortunately, if a boiler engineer discovers that the boiler is leaking water from the heat exchanger, this is the end of the road for your system. The heat exchanger is the most expensive part of your boiler, so it makes more financial sense to replace your boiler with a newer, more efficient model rather than try to replace it.

During a boiler service, your boiler engineer will perform a series of checks to ensure that your boiler is safe and efficient. First, they will conduct a visual inspection to check for any corrosion or leaks. They will also check the flame in your boiler. They’ll then remove the boiler casing and check all the components, including the heat exchanger, burner and spark probe, then clean the inside. After this, they’ll check the flue for obstructions and ensure that it’s safely fitted. They will then do a gas pressure check to ensure the boiler is working at the right pressure, before firing it up to check for any working faults.

If you’re looking to acquire smart thermostats in your home, but wondering about its money saving qualities, then this is for you! Not only do smart thermostats add new impressive features to your home, but it can also save you both energy and money. According to many reports using a programmable thermostat can save you between the range of £130 to £150 on an annual basis. Now think about using a smart thermostat that makes it a lot more easier for you.

Wondering how smart thermostat save money? Simply set your smart thermostat one or two degrees lower or higher than the usual number. Once done, you’re likely to notice 1% to 3% reduction in your energy bills. And if you want even more, you simply increase the percentage to about 10 degrees to 15 degrees to cover the period you spend at work and watch as you save up to 10 percent of your energy bills.

Generally, a smart thermostats will save you money in two major ways. These includes:

• They Do All The Thinking For You

The smart thermostat watches your behaviour and study the time you’re at home and when you’re not as well as your preferred temperature at particular times in a day, and that’s why they are termed as “smart. they’ll automatically adjust the settings to ensure you get home to a perfect temperature.

• They Keep Tabs On Your Usage

You can always count on a two way communicating smart thermostat to watch your usage while also collecting the data and sharing it with you. It informs you of your energy usage rate as well as the estimated amount. Once you’ve been notified, you can manual adjustment or leave it to the thermostat to help manage your energy.

Can You Replace A Gas Boiler With An Electric Boiler?

In the UK, there are about 22 million households that are heated with the use of a gas boiler. However, do not assume that they’re the best type of boiler to install. The fact is, if your house isn’t connected to the main gas supply, the best option is for you to install an electric boiler rather than a gas boiler. So is it possible to replace a gas boiler with an electric boiler? The simple answer is yes. Both heating system options work in varying ways and also with a different impact on the environment.

The gas boiler is able to generate heat with the help of a gas burner. A heat exchanger is linked to the burner and heats the water available in its chamber. The hot water is then supplied to the heating circuit.

However, the thing is that natural gas can actually be more affordable when compared to using electricity to operate your boiler, but they have a negative impact on the environment. This is because gas boilers make use of an odourless, colourless and poisonous gas - carbon monoxide.

Meanwhile electric boilers are powered by electrical energy, hence, no carbon monoxide leak risks. Instead of using gas to heat up water, electric boilers distribute energy to heating elements which, in turn, heats up the water. So thinking about what’s best for the environment, you’d go for electric boilers. However, they’re more costly and are not as efficient as oil boilers.

If you reside in a smaller house that’s not connected to the main gas supply, then you might want to consider installing an electric boiler. However, if you live in a larger house, an electric boiler may not be the best option as they’re mostly designed to generate little quantity of hot water.