Find a Heating Engineer you can trust in West Drayton.

How To Fix A Broken Boiler

To fix any problem when it comes to home appliances, the first step is always to identify the problem while also carrying out thorough checks - a broken boiler is not an exception. Putting enough time and effort in diagnosing a problem can go a lot way to save you both time and money. So here are some of the steps you can take to fix your broken boiler before you put a call out to a licensed engineer.

✓ Check to confirm if your pilot light is on. Whenever you’re facing some issues with your boiler, this should always be the first thing you do. The pilot light being on speak volumes, if the light is off then there’s absolutely no way the flame can start the appliance’s gas supply. You should try to put it back on, if off. To do this, you simply have to follow the detailed instructions on your boiler’s manual strictly. If after following these actions to the letter and the issue remains the same, then you’d probably need the services of an a qualified engineer. Never try to fix the issue on your own.

✓ Check the pressure. The solution to the headaches might sometimes be as simple as examining your appliance’s pressure gauge. Here, the good numbers are around 1.0 or1.5, if it happens to fall below this, then you should open the boiler’s instruction manual. You can also inspect your radiator valves for any leaks. You’d have to call in a specialist to solve the issue.

✓ Check the thermostat. Here, it’s important to note that a faulty thermostat doesn’t necessarily imply a broken boiler. It may just signify that you need to replace your thermostat. Simply check to ensure that your thermostat is turned on and temperature is at the appropriate degree.

A boiler is simply the most important part of a central heating system as it generates the heat that warms up the home or property. Basically, the appliance or small furnace makes use of gas, LPG or oil in order to fuel its operation. However in the UK, most boilers are usually fuelled by natural gas which is supplied automatically from the national gas grid. And depending on how it operates, there are various types of boilers.

Typically, a gas central heating boiler will have multiple pipes entering from underneath. While one pipe supplies the boiler with gas from the mains gas supply, another pipe allows cold water to enter the boiler to be heated, the last pipe then enables hot water to exit the boiler so it can be distributed around the home.

✓ There are fuel jets and heat exchangers inside the boiler. When the heating is turned on, a valve is opened to allow the mains supply gas to enter a sealed combustion chamber in the boiler. There are multiple little valves which permit the entry of the gas before being ignited by an electric ignition switch. These jets heat a metal component in the boiler known as a heat exchanger which works to transfer the heat to the cold water pipe and heat up the water.

✓ Once the water has been heated to the target temperature, it’s then pumped through a circuit of pipe which runs around your home by an electric pump.

✓ The heated water enter each radiator, is then transmitted via a closed loop and radiates heat into each room.

✓ Once done travelling through all radiators, the water then returns to the boiler at which it must have been cooled. Therefore, the boiler will have to reheat following the same process before circulating. The water can only be drained by a professional Gas Safe engineer

How To Install A Gas Cooktop In An Island

Are you thinking about installing a gas cooktop in your kitchen island? If yes, then you must know that there are clearance requirements that must be met (before you proceed) between the cut out and the countertop’s edge. Basically, there are incremental requirements for island installation due to the fact that it does not make an assumption that the product is going to be fitted against a rear wall that acts to protect the back of the unit. As a result, while doing an island install we must put the safety of the product into consideration much more that we do a standard install. What’s more? This island clearance requirement develops from a third-party agency and is a standard with all brands. So how do you install a gas cooktop in an island having the aforementioned requirements in mind?

• Use a foil tape to line the inside edges of the cut out. The function of this is to prevent heat damage as well as countertop’s discolouration. Put the cooktop top on a secured surface.

• Identify the pipe coming out of the cooktop’s side or bottom and brush onto the threads of the manifold entrance.

• Pass the pressure regulator onto the entrance of the manifold and make use of a wrench to tighten it.

• Brush the pipe joint compound onto one of the flare union adaptor’s threads and pass it into the regulator’s open end. Make it slightly tight with a full turn of the wrench.

• Connect the flare union adaptor’s open end with the flexible appliance connector hose, upon brushing on pipe joint compound.

• Put foam tape on the cooktop underside’s edges, if your cooktop comes with a glass burner plate.

• Turn the cooktop to set it into the cutout.

• Apply pipe-joint compound onto the flare union adaptor left and secure it firmly into the gas shutout valve.

• Connect the flexible hose connector’s free end with the flare union adaptor.

If you’re thinking about getting a new gas boiler for your home or property, then you might also be wondering how much it’ll cost you so you can set a budget and start planning. As simple as this question sounds, it’s actually very tricky to provide a simple and short answer as the costs of installing a new gas boiler alone varies greatly based on the parts needed, the amount of work required, your location, their availability as well as the company you hire for the project.

When it comes to purchasing a new gas boiler the price you’re expected to pay also depends on multiple influencing factors such as the type, brand as well as your most preferred gas boiler model. However, one thing you should have in mind is the fact that your gas boiler is right at the heart of your home or property and can be a complicated piece of machinery. As a result, you wouldn’t expect gas boilers to come cheap. Generally, it’s going to cost within the range of £500 to about £2,500 to get a new gas boiler. Therefore, it’s always advisable to obtain all necessary details and facts before you decide to purchase a replacement gas boiler.

This price range may seem too high as it’s usually a turn off for most homeowners. However, it’s worth noting that gas boiler replacement costs and gas boiler installation costs are, more often than not, compensated by the saving you’ll make off your utility bills - all thanks to the new and more energy efficient boiler you just installed in your home. And even more importantly, when it has been estimated that roughly half of the amount spent on energy on an annual basis depends on your boiler.

When it comes to gas boilers, this is one of the most frequent questions that always pops up and for a good reason. When you invest a considerable amount of money to acquire and install a gas boiler in your business property, it’s only reasonable not only to expect the boiler to warm up your property efficiently, but also to do so for a long period of time. If you’ve just bought or about to get a new gas boiler, it’s likely you won’t have to worry about getting a replacement for a lengthy period of time. Several commercial gas boilers will last for anywhere between 10 to 15 years on the average. However in the event whereby you have an existing one that’s fast approaching the end of it’s useful life, then you should know the time go get a new gas boiler is just around the corner, and the earlier you make the purchase, the better (to avoid any surprise breakdowns that’ll leave your home super uncomfortable).

Just like any other home appliance, it’s a fact that an older gas boiler ( especially those that have been installed over a decade ago) are significantly less efficient that the new modern ones. When the older versions were manufactured is a completely different time to now as both technology and climate concerns are wide apart. So when your existing boiler is approaching the end of it’s useful life, it’ll be wise to start saving up to cover the cost of getting a new one. However, if it’s only about 5 years ago your boiler was installed, it’s highly likely to still be very efficient.

How Long Does A Gas Safety Certificate Last?

As a result of faulty installation and irregular maintenance of gas appliances and chimneys, a lot of people have been met with an untimely death caused by the toxic gas - carbon monoxide. This is a gas that’s completely odourless, colourless and tasteless - meaning you can’t identify one of its in the environment. But what you should know is, if you stay in an environment filled with carbon monoxide, you’d probably be dead within a couple of hours. Consequently as a landlord, you must do what’s best to ensure the safety of all your tenants by making sure that all your gas appliances and chimneys are subjected to annual check by an approved Gas Safe engineer as required by the law.

Wondering how long a Gas Safety Check will take? The safety of your gas is guaranteed by carrying out regular examinations. Whether or not you possess a gas alarm, it’s still vital to conduct regular gas safe checks to make sure your home is safe. A typical gas safe check would last between 30 to 60 minutes for a normal domestic property. However, in the situations whereby a need for repair arises, it may take longer time to complete. Other factors that can also affect the timing includes includes both the size and location of your property.

So how long does a gas safety certificate last? The simple answer to this question is 12 months. If you own a rental property in the UK, it’s up to you to ensure all your gas appliances and chimney is check after every 12 months to obtain a Gas Safety Certificate which you should hand out a copy to all tenants living in your property. However, if you don’t own the property, you can inform your landlord to get one as soon as possible while also providing a carbon monoxide alarm.

If your boiler is leaking, there are some checks that you can do yourself. However, you should never attempt to repair your boiler yourself – only a Gas Safe-registered engineer should conduct repairs.

There are 3 main reasons why your boiler might be leaking: there’s a pressure valve fault, a temperature valve leak or corrosion in the system. An engineer will be able to spot the problem quickly, but in the meantime there are a few things you can do:

Check the pipe fittings

If your boiler is leaking water around the pipe fittings, it could be an installation fault and you should get in touch with the engineer that fitted it. You can check the pipe fittings by drying the area then waiting to see if the water appears again. If it does, you may be able to do a ¼ turn of the pipe to stop it. However, you should still call the engineer that installed it to ask them to check the PTFE tape on the inside.

Inspect the seals

Over time, the rubber seals on a boiler can start to perish, so if you have an old boiler this could be the source of your leak. If you have a new boiler, it could be caused by your boiler running over pressure.

Heat exchanger corrosion

Unfortunately, if a boiler engineer discovers that the boiler is leaking water from the heat exchanger, this is the end of the road for your system. The heat exchanger is the most expensive part of your boiler, so it makes more financial sense to replace your boiler with a newer, more efficient model rather than try to replace it.

When your boiler is being replaced you won’t have hot water or central heating. If you don’t mind this you can stay in your home, and use portable electric heaters if needed. Most installers undertake a power flush before installing a new boiler now and this can cause muck and debris from the pipework, so you may wish to get out of the way while this is happening!