Find a Heating Engineer you can trust near you.

Re-pressurising your boiler means that you allow more water to enter system via the filling loop. It can be easy to re-pressurise your boiler yourself. Always check your manual, but there are some simple steps you can take to restore pressure to your boiler:

• Switch off your boiler and let it cool completely

• Make sure both ends of your filling loop are attached

• Open both valves to allow cold water into the system – you’ll hear it start to move

• Look out for your pressure gauge to show 1.5 bar

• Close both valves

• Switch your boiler back on

• Undo both ends of your filling loop and remove it. Remember some water might come out, so be ready to catch some spillage!

Modern oil boilers do not require a lot of maintenance. OFTEC recommends that oil boilers are serviced and inspected every year. This keeps them running as efficiently as possible and will ensure any issues with your boiler are identified before they cause bigger problems. This servicing is also vital because of the increased risk of carbon monoxide leaking from a poorly maintained boiler.

If your boiler is leaking, there are some checks that you can do yourself. However, you should never attempt to repair your boiler yourself – only a Gas Safe-registered engineer should conduct repairs.

There are 3 main reasons why your boiler might be leaking: there’s a pressure valve fault, a temperature valve leak or corrosion in the system. An engineer will be able to spot the problem quickly, but in the meantime there are a few things you can do:

Check the pipe fittings

If your boiler is leaking water around the pipe fittings, it could be an installation fault and you should get in touch with the engineer that fitted it. You can check the pipe fittings by drying the area then waiting to see if the water appears again. If it does, you may be able to do a ¼ turn of the pipe to stop it. However, you should still call the engineer that installed it to ask them to check the PTFE tape on the inside.

Inspect the seals

Over time, the rubber seals on a boiler can start to perish, so if you have an old boiler this could be the source of your leak. If you have a new boiler, it could be caused by your boiler running over pressure.

Heat exchanger corrosion

Unfortunately, if a boiler engineer discovers that the boiler is leaking water from the heat exchanger, this is the end of the road for your system. The heat exchanger is the most expensive part of your boiler, so it makes more financial sense to replace your boiler with a newer, more efficient model rather than try to replace it.

When it comes to gas boilers, this is one of the most frequent questions that always pops up and for a good reason. When you invest a considerable amount of money to acquire and install a gas boiler in your business property, it’s only reasonable not only to expect the boiler to warm up your property efficiently, but also to do so for a long period of time. If you’ve just bought or about to get a new gas boiler, it’s likely you won’t have to worry about getting a replacement for a lengthy period of time. Several commercial gas boilers will last for anywhere between 10 to 15 years on the average. However in the event whereby you have an existing one that’s fast approaching the end of it’s useful life, then you should know the time go get a new gas boiler is just around the corner, and the earlier you make the purchase, the better (to avoid any surprise breakdowns that’ll leave your home super uncomfortable).

Just like any other home appliance, it’s a fact that an older gas boiler ( especially those that have been installed over a decade ago) are significantly less efficient that the new modern ones. When the older versions were manufactured is a completely different time to now as both technology and climate concerns are wide apart. So when your existing boiler is approaching the end of it’s useful life, it’ll be wise to start saving up to cover the cost of getting a new one. However, if it’s only about 5 years ago your boiler was installed, it’s highly likely to still be very efficient.

A combination boiler, also referred to as a “combi boiler, delivers both domestic hot water and space heating in a single package so as to save space, and in a lot of cases, money. These great features makes the appliance a very popular choice in UK homes and in fact, it represents more than 50 percent of all new boilers fitted in the UK on a yearly basis.

Most modern and high efficiency combi boilers are usually stainless steel condensing boilers which normally features an in-built secondary heat exchanger to deliver domestic hot water to a home or property. What’s more? When it comes to the heating season or the cold months, the combi boiler will operated as required to heat a structure and offer hot water for showers, sinks as well as other hot water appliances around the house. And when it gets to the warm season or summer months, the combi boiler will only work when there’s a need for domestic hot water which also helps you save more money.

Combi boilers are able to provide domestic hot water in such a way that’s energy efficient due to two primary reasons - the combi units possess a very high operating efficiency and also have a low internal water volume. As a result, in during the hot summer when space heating is not required, you’ll only have to pay to heat up the hot water that you really need and not an entire tank.

Combi boilers also have the following benefits:

✓ Lower costs. Due to the combined nature of the boiler and the lack of tank in the roof space, the installation time and costs are at a minimum.

✓ Saves space in your home as it effectively combines a central heating boiler with a water heater into one unit.

How Often To Service Boiler?

A boiler is a vital part of any home especially if you’re in the UK. Not only does provide your entire household with hot water and keep them warm but also adds a good value to your property. Boiler repairs and replacement are both super expensive and stressful, so in order to avoid all these worries, it’s better to have your boiler serviced on a regular basis for your own peace of mind. When you call in a reliable heating engineer, it can immensely raise your boiler’s efficiency while also saving you from more expensive issues down the road.

So if you haven’t had your boiler serviced for quite some time, moved into a new house and not aware the last time your boiler was serviced or perhaps you’re just wondering how often a boiler should be serviced, then you’ve come to the right place! The short and simple answer to this question is a boiler should should be serviced once in a year, and most preferably during the summer months. However, there are a wide range of factors that comes into play so it’s always advisable to check with your manufacturer before you proceed.

According to the law, you’re required to have your boiler services on an annual basis. Failure to do so can render your boiler or home warranty void. Therefore, it’s very crucial to take down the last time your boiler was serviced and also set a reminder to book your next appointment when the time closes in.

If you happen to own an electric boiler you may not need an annual servicing. But you may still be required to perform it annually by your insurance provider.

How Does Electric Central Heating Work?

An electric central heating works to provide a number of benefits for you. These benefits include the following:

lSpace Heating

• The storage heaters work during the night to store electricity which would be used to heat up the heat retaining bricks. This, in turn, will release this energy throughout the day to warm up the room.

• There are also electric radiators which works to deliver on-demand heat and as a result, economy tariffs are totally avoided. It will generate heat by itself rather than storing it and with the controls, you can easily determine the amount of heat to be released when you require it.

• There is the wet electric system options as well which comes with water filled radiators. This operates in a similar way to normal radiators, however, it makes use of electricity to heat up the water.

lWater Heating

• An electric boiler operates in a very similar manner to other boiler types, just that it makes use of electricity as its fuel. Here, the water is warmed by a heating element and the water is later moved to several radiator throughout the house by a pump. These electric boiler types earns you tariff savings as you’ll be able to heat water at night.

• Heat pumps geothermal or air source, redistributes heat instead of creating it. Heat pumps are powered by electricity and it works by absorbing heat either from the air or ground which it then channels it through a pump. This can then be incorporated in heating either water or a room.

• A dedicated immersion heater is another water heating option. Here, the heating element is positioned inside a hot water cylinder. In a similar fashion to a kettle, the element heats the nearby water. Immersion heater can act either as a backup or your main heating element.

How Do You Bleed An Oil Boiler?

Bleeding air between the oil supply and an oil fired boiler’s burner is a process that’s often required when the system has run out of oil and the burner has stopped working. Upon refilling the oil tank, the air that has been trapped within the oil pipe when empty has to be freed to ensure that the oil reaches the burner and allows it to start again. So how do you go about the process?

First and foremost, it must be noted that it’s always better to be on the look out for the amount of oil in your fuel tank and get it refilled before it runs out. However, if it does run out, you can take the following steps:

• Identify the burner

The burner is a red plastic cover and it’s usually positioned on the bottom part of the boiler (mostly inside the boiler casing). Once identified, inspect it to see if the lockout button is lit red. If yes, simply unscrew and detach the burner’s red case using a flat head screwdriver.

• Identify the oil pump

You’ll find the oil pump on the burner’s left side which is connected to the flexible oil line. Once done, simply locate the 3 inches long hexagonal stem protruding from the pump and with a small threaded plug screwed into the end. Unscrew the plug in just half a turn ( 180 degrees) with a 4mm Allen Key. At this stage oil will be released, do ensure there’s a cloth or rag underneath the plug to grab the oil freed.

• Press the lockout button

This is the next and final step. However it’s also crucial to note that the burner fan will run for about 12 seconds and discharge some oil from the loosened plug which you can grab with a cloth or rag. Immediately you hear a buzzing sound, use the Allen key to tighten the plug. If enough air has been bled, the system will fire. But if not, then you’ll have to repeat the process again.