Find a Heating Engineer you can trust in Isle Of Man.

Re-pressurising your boiler means that you allow more water to enter system via the filling loop. It can be easy to re-pressurise your boiler yourself. Always check your manual, but there are some simple steps you can take to restore pressure to your boiler:

• Switch off your boiler and let it cool completely

• Make sure both ends of your filling loop are attached

• Open both valves to allow cold water into the system – you’ll hear it start to move

• Look out for your pressure gauge to show 1.5 bar

• Close both valves

• Switch your boiler back on

• Undo both ends of your filling loop and remove it. Remember some water might come out, so be ready to catch some spillage!

How To Install An Oil Boiler Heating System

Just like several other skills, the installation of an oil boiler heating system can be a challenge. It requires enough persistence to actually get right, so if you’re the type with little patience, we’d recommend you hire the services of a professional oil boiler heating system fitter who can guarantee the best results and save you time and extra money due to potential damages.

To install your boiler system yourself, it’s always advisable to start by getting the information on the best installation processes from the supplying company which will go a long way to save you from future headaches. However, we’ve put together this guide to give you a basic knowledge on how its done. Let’s have a look!

lRead Instruction Manual

• Carefully read and digest the instruction manual thoroughly.

• Make sure you understand the installation diagrams

• Spread out the materials and get familiar with them.

lFigure Out What Goes Where

• Take your time to determine where everything goes in relation to the others.

• Identify the new radiator’s position.

• Get sufficient sealants to prevent possible leakages inside the walls.

lIdentify The Pipe Routes

• Determine the pipe routes while fitting the new radiators

lInstall The Boiler

• Turn off water and all electrics

• Fit the boiler into the wall

• Make sure the fittings are secured.

lInstall The Radiator

• The effectiveness of your home’s heating system is as good as the radiators you incorporate and how good they’re installed.

• You may have to utilize extra radiators in large open plan kitchens and living rooms (for effective heating).

lOffer Ventilation

• Once you’ve successfully installed the new radiator, a small dose of air ventilation would be needed.

• Turn the key of each valve located at the bottom, do not stop until a little amount of water spills over the top of the unit.

Can You Get Oiled Fired Combi Boilers?

Absolutely! Oil fired combi boilers are not only a super cool alternative to gas heating, but also offer a cost-efficient means of heating your home. And this is best enjoyed especially if you’re one of the estimated 4 million houses that are not connected to the gas network.

Oil fired combi boiler enables you store fuel close to your property and fill it as required. There many A rated model options available in the market with the modern oil fired combi boilers confirmed to be up to 95% efficient. As a result of their multiple advantages over alternative heating systems, the oil fired combi boiler is expected to increase significantly in the UK. Here are some of the advantages of adding the system to your property.

• Oil fired combi boiler heats up water on demand while also saving a lot of fuel and being super energy efficient.

• Since oil needs more fuel than gas, a great return would be derived from every unit of energy.

• When compared with the other types of boilers, oil fired combi boilers have a considerably lower operating cost.

• A new oil fired boiler typically has a 92% to 95 % efficiency, which is significantly better than the 60% to 70% in older systems.

If you have an idea of how to operate the gas-powered alternative, then operating an oil fired combi boiler shouldn’t be an issue. In a similar way to the alternative, the boiler simply delivers the central heating through the radiators and hot water via your household’s taps.

However, the major difference between the two is the fact that the oil fired boiler needs a regular supply of oil, which is stored in a tank. The hot water supplied by the system is instant as it is connected to the water mains supply.

How Do You Bleed An Oil Boiler?

Bleeding air between the oil supply and an oil fired boiler’s burner is a process that’s often required when the system has run out of oil and the burner has stopped working. Upon refilling the oil tank, the air that has been trapped within the oil pipe when empty has to be freed to ensure that the oil reaches the burner and allows it to start again. So how do you go about the process?

First and foremost, it must be noted that it’s always better to be on the look out for the amount of oil in your fuel tank and get it refilled before it runs out. However, if it does run out, you can take the following steps:

• Identify the burner

The burner is a red plastic cover and it’s usually positioned on the bottom part of the boiler (mostly inside the boiler casing). Once identified, inspect it to see if the lockout button is lit red. If yes, simply unscrew and detach the burner’s red case using a flat head screwdriver.

• Identify the oil pump

You’ll find the oil pump on the burner’s left side which is connected to the flexible oil line. Once done, simply locate the 3 inches long hexagonal stem protruding from the pump and with a small threaded plug screwed into the end. Unscrew the plug in just half a turn ( 180 degrees) with a 4mm Allen Key. At this stage oil will be released, do ensure there’s a cloth or rag underneath the plug to grab the oil freed.

• Press the lockout button

This is the next and final step. However it’s also crucial to note that the burner fan will run for about 12 seconds and discharge some oil from the loosened plug which you can grab with a cloth or rag. Immediately you hear a buzzing sound, use the Allen key to tighten the plug. If enough air has been bled, the system will fire. But if not, then you’ll have to repeat the process again.

The A-G scale refers to the energy efficiency of your boiler. G-rated boilers are the least efficient, and give you less heat and hot water for your money. Installing an A-rated boiler will reduce your energy bills and carbon emissions. Don't compromise on cheaper, lower rated boilers, you will save yourself more money longer term with an A-rated model.

If your property is not connected to a gas main, oil boilers are a great alternative to gas boilers and more efficient than LPG alternatives. They can also be paired well with renewable sources. However, if your property is connected to the gas mains, there is generally no reason to switch to an oil boiler, as you will need to have oil delivered to an extra storage tank.

Your LPG storage tank should have a gauge that shows you how much fuel it has in it. Most LPG suppliers suggest that you arrange a fuel delivery when the level in your tank gets down to about 20%. Make regular checks, particularly in the winter when you will use more, so you know when levels are low.

If you’re looking for a reliable or reputable source for your new gas boiler, you definitely won’t find much better than British Gas. Using a big firm like British Gas comes with a plethora of benefits , but of course there are also some drawbacks, with the boiler prices being the main one and biggest turn off for most homeowners. However, just before we delve straight in to the price, let’s look at a thing or two about the big company.

The company, “British Gas are not a boiler manufacturer as you probably would have first imagined. They’re actually a company that specializes in the installation of boilers. As a result, they’re able to install just about any type of boiler you can imagine from any manufacturer. Be it a Worcester Bosch Greenstar 8000 Style or a Baxi 600, they’re able to provide you with the cost of having these boilers installed in your home or property.

Combi boilers are perfect boilers for space-saving and this makes them very popular on the market. They’re also very efficient when it comes to heating water instantly and warm your in few minutes. The price of a new British Gas combi boiler varies on a number of factors. Generally, the installation prices of combi boilers start from £1,800. Therefore, if British Gas are to be competitive with their pricing it should also be around this price.

However, if you have a large house with several rooms with a higher demand for hot water, British Gas will most likely recommend boilers such as Worcester Bosch 440CDi and the likes. Judging from other firms in the market, the price to have these types installed should be in excess of £3,000.