Find a Heating Engineer you can trust in Presteigne.

How Do You Bleed An Oil Boiler?

Bleeding air between the oil supply and an oil fired boiler’s burner is a process that’s often required when the system has run out of oil and the burner has stopped working. Upon refilling the oil tank, the air that has been trapped within the oil pipe when empty has to be freed to ensure that the oil reaches the burner and allows it to start again. So how do you go about the process?

First and foremost, it must be noted that it’s always better to be on the look out for the amount of oil in your fuel tank and get it refilled before it runs out. However, if it does run out, you can take the following steps:

• Identify the burner

The burner is a red plastic cover and it’s usually positioned on the bottom part of the boiler (mostly inside the boiler casing). Once identified, inspect it to see if the lockout button is lit red. If yes, simply unscrew and detach the burner’s red case using a flat head screwdriver.

• Identify the oil pump

You’ll find the oil pump on the burner’s left side which is connected to the flexible oil line. Once done, simply locate the 3 inches long hexagonal stem protruding from the pump and with a small threaded plug screwed into the end. Unscrew the plug in just half a turn ( 180 degrees) with a 4mm Allen Key. At this stage oil will be released, do ensure there’s a cloth or rag underneath the plug to grab the oil freed.

• Press the lockout button

This is the next and final step. However it’s also crucial to note that the burner fan will run for about 12 seconds and discharge some oil from the loosened plug which you can grab with a cloth or rag. Immediately you hear a buzzing sound, use the Allen key to tighten the plug. If enough air has been bled, the system will fire. But if not, then you’ll have to repeat the process again.

A boiler is simply the most important part of a central heating system as it generates the heat that warms up the home or property. Basically, the appliance or small furnace makes use of gas, LPG or oil in order to fuel its operation. However in the UK, most boilers are usually fuelled by natural gas which is supplied automatically from the national gas grid. And depending on how it operates, there are various types of boilers.

Typically, a gas central heating boiler will have multiple pipes entering from underneath. While one pipe supplies the boiler with gas from the mains gas supply, another pipe allows cold water to enter the boiler to be heated, the last pipe then enables hot water to exit the boiler so it can be distributed around the home.

✓ There are fuel jets and heat exchangers inside the boiler. When the heating is turned on, a valve is opened to allow the mains supply gas to enter a sealed combustion chamber in the boiler. There are multiple little valves which permit the entry of the gas before being ignited by an electric ignition switch. These jets heat a metal component in the boiler known as a heat exchanger which works to transfer the heat to the cold water pipe and heat up the water.

✓ Once the water has been heated to the target temperature, it’s then pumped through a circuit of pipe which runs around your home by an electric pump.

✓ The heated water enter each radiator, is then transmitted via a closed loop and radiates heat into each room.

✓ Once done travelling through all radiators, the water then returns to the boiler at which it must have been cooled. Therefore, the boiler will have to reheat following the same process before circulating. The water can only be drained by a professional Gas Safe engineer

Are you worried about blocked drains? Yes, you probably should! As a homeowner ( with a detached, semi detached or terraced house), all plumbing and drainage issues within your home or even within your property boundary is your responsibility. Hence, you’d might want to consider getting a Homeserve plumbing and drainage cover to help keep your home running smoothly and putting your mind at ease. The only exception here is if the drain in question is a lateral drain which is a common feature in flats. In this situation, it’s only the building managers that would be responsible for the maintenance of the drainage as it’s shared between several homes. Before 2011, the various flats or houses that shares the lateral drain are responsible for its maintenance.

Working with top utility companies for over 2 decades, Homeserve has positioned itself as one of the leading home assistance providers in the United Kingdom. With their top notch services, they’ve been able to make their client’s lives a lot easier and stress free through the provision of a wide array of repair solutions such as drainage, plumbing, heating, electrics and a lot more.

As a homeowner with the responsibility of maintaining the drains and ensuring there’s no block or damage, it’s simply a no brainer to go for a plumbing and drainage cover and more importantly, get good cover. Homeserve are one of the providers but there are a number of others which offer great service at competitive prices. Without an insurance in place, you may just have to break the bank just to have an engineer or plumber to fix any plumbing or drainage issue you might have. So why not give yourself a peace of mind and get a cover today?

If you’re looking to acquire smart thermostats in your home, but wondering about its money saving qualities, then this is for you! Not only do smart thermostats add new impressive features to your home, but it can also save you both energy and money. According to many reports using a programmable thermostat can save you between the range of £130 to £150 on an annual basis. Now think about using a smart thermostat that makes it a lot more easier for you.

Wondering how smart thermostat save money? Simply set your smart thermostat one or two degrees lower or higher than the usual number. Once done, you’re likely to notice 1% to 3% reduction in your energy bills. And if you want even more, you simply increase the percentage to about 10 degrees to 15 degrees to cover the period you spend at work and watch as you save up to 10 percent of your energy bills.

Generally, a smart thermostats will save you money in two major ways. These includes:

• They Do All The Thinking For You

The smart thermostat watches your behaviour and study the time you’re at home and when you’re not as well as your preferred temperature at particular times in a day, and that’s why they are termed as “smart. they’ll automatically adjust the settings to ensure you get home to a perfect temperature.

• They Keep Tabs On Your Usage

You can always count on a two way communicating smart thermostat to watch your usage while also collecting the data and sharing it with you. It informs you of your energy usage rate as well as the estimated amount. Once you’ve been notified, you can manual adjustment or leave it to the thermostat to help manage your energy.

The Oil Firing Technical Association or OFTEC operate a competent persons scheme to certify installers. It’s always recommended to use an installer with this certification as it proves they have the training and expertise to properly install your boiler and give you realistic advice on the efficiency of your system. Also, OFTEC registered installers offer Workmanship Warranties to protect you if there are any problems after installation.

What Is A Gas Safety Certificate?

Do you wish to know what a Gas Safety Certificate is and if you need to get one?

If you’re in the UK and you own a rental property, you have a statutory obligation to obtain a Gas Safety Certificate. The law ( Gas Safety - Installation and Use, Regulations 1998) stipulates that landlords as a matter of necessity should have all their gas appliances, fittings,and property flues subjected to yearly checks in order to ensure that they’re are totally safe.

The Gas Safety Certificate can be referred to in a number of ways which includes Landlord Gas Safety Record ( LGSR) or CORGI PROFORMA 12 (CP12). The later dating back to when the official body for gas safety in the UK was CORGI. However, the official body is now known as Gas Safe, hence it’s now usually called a Gas Safety Certificate or something along that line. But regardless of whatever you choose to call it, as long as you reside in the UK, it’s crucial to know that if you need one as soon as possible. So how do know if you need a Gas Safety Certificate?

If you’re a homeowner with a property that you live in, you’re not required by the law to obtain a Gas Safety Certificate. There’s nothing like a homeowner’s gas safety certificate, however we’d recommend you subject all you gas appliances and pipework to yearly examinations to ensure they’re functioning properly and safely.

If you’re a landlord in the UK, you’re required by the law to get a Gas Safety Certificate to ensure your property is safe for your tenants. You must reach out to an approved Gas Safe engineer who’ll carry out annual checks on your appliances to ensure that they’re totally safe.

During a boiler service, your boiler engineer will perform a series of checks to ensure that your boiler is safe and efficient. First, they will conduct a visual inspection to check for any corrosion or leaks. They will also check the flame in your boiler. They’ll then remove the boiler casing and check all the components, including the heat exchanger, burner and spark probe, then clean the inside. After this, they’ll check the flue for obstructions and ensure that it’s safely fitted. They will then do a gas pressure check to ensure the boiler is working at the right pressure, before firing it up to check for any working faults.

How To Get A Gas Fireplace Installed

A gas fireplace is one of the most popular means of adding warmth to homes which so many homeowners have now come to terms with, especially with natural gas prices being fairly low for an extended period of time. Properly installed gas fireplaces are not only capable of adding a much needed ambiance and warmth to your home, but also significantly more efficient than the traditional wood-burning fireplaces which mostly produces less heat from the large amount of drafts they consume. Meanwhile a good gas powered fireplace with a properly functioning blower, is very close to being as efficient as a furnace when warming up a room. What’s more? Gas fireplaces also possess a great visual appeal and are also very practical especially when they feature realistic ceramic logs as well as good gas burners.

Installing a gas fireplace by yourself is definitely up there as one of the most advanced DIY tasks you can attempt to try. If you lack proper training and experience, it’s advisable you leave the task to a reliable professional that’ll guarantee the best results while also ensuring costly errors are avoided. This guide will, however, put you in the right direction.

• Construct wall recess to accept the fireplace.

• Punch a hole through the exterior wall of the house to fit in stovepipe thimble.

• Fix a small part of the stovepipe to the exhaust port in the fireplace’s rear.

• Use construction adhesives on the wall around the fireplace opening’s sides and top.

• Apply granite slabs into the adhesive around the opening of the fireplace.

• Put the fireplace in position and ensure the stovepipe goes outdoors through the thimble.

• Use a termination hood to seal the exhaust pipe’s exterior.

• Employ the services of a professional plumber to connect the gas to the fireplace.

• Fit the removable front

• Test the functionality of the fireplace.