Find a Heating Engineer you can trust in Wemyss Bay.

If your boiler is leaking, there are some checks that you can do yourself. However, you should never attempt to repair your boiler yourself – only a Gas Safe-registered engineer should conduct repairs.

There are 3 main reasons why your boiler might be leaking: there’s a pressure valve fault, a temperature valve leak or corrosion in the system. An engineer will be able to spot the problem quickly, but in the meantime there are a few things you can do:

Check the pipe fittings

If your boiler is leaking water around the pipe fittings, it could be an installation fault and you should get in touch with the engineer that fitted it. You can check the pipe fittings by drying the area then waiting to see if the water appears again. If it does, you may be able to do a ¼ turn of the pipe to stop it. However, you should still call the engineer that installed it to ask them to check the PTFE tape on the inside.

Inspect the seals

Over time, the rubber seals on a boiler can start to perish, so if you have an old boiler this could be the source of your leak. If you have a new boiler, it could be caused by your boiler running over pressure.

Heat exchanger corrosion

Unfortunately, if a boiler engineer discovers that the boiler is leaking water from the heat exchanger, this is the end of the road for your system. The heat exchanger is the most expensive part of your boiler, so it makes more financial sense to replace your boiler with a newer, more efficient model rather than try to replace it.

Biomass boilers do require some maintenance. Many manufacturers recommend servicing twice a year, although this is often included in the installation cost. Many systems have automatic fuel loading that removes the need to manually load fuel. You will need to remove the ash from the boiler, but this is as easy as emptying a vacuum cleaner.

How To Install A Gas Cooktop In An Island

Are you thinking about installing a gas cooktop in your kitchen island? If yes, then you must know that there are clearance requirements that must be met (before you proceed) between the cut out and the countertop’s edge. Basically, there are incremental requirements for island installation due to the fact that it does not make an assumption that the product is going to be fitted against a rear wall that acts to protect the back of the unit. As a result, while doing an island install we must put the safety of the product into consideration much more that we do a standard install. What’s more? This island clearance requirement develops from a third-party agency and is a standard with all brands. So how do you install a gas cooktop in an island having the aforementioned requirements in mind?

• Use a foil tape to line the inside edges of the cut out. The function of this is to prevent heat damage as well as countertop’s discolouration. Put the cooktop top on a secured surface.

• Identify the pipe coming out of the cooktop’s side or bottom and brush onto the threads of the manifold entrance.

• Pass the pressure regulator onto the entrance of the manifold and make use of a wrench to tighten it.

• Brush the pipe joint compound onto one of the flare union adaptor’s threads and pass it into the regulator’s open end. Make it slightly tight with a full turn of the wrench.

• Connect the flare union adaptor’s open end with the flexible appliance connector hose, upon brushing on pipe joint compound.

• Put foam tape on the cooktop underside’s edges, if your cooktop comes with a glass burner plate.

• Turn the cooktop to set it into the cutout.

• Apply pipe-joint compound onto the flare union adaptor left and secure it firmly into the gas shutout valve.

• Connect the flexible hose connector’s free end with the flare union adaptor.

If you’re interested in deriving maximum benefits from your central heating system while also being a tech-enthusiast, a smart thermostat is just the perfect option as it allows you to control both your boiler and heating system via your mobile device. It also offers a plethora of features which enables you to heat your home more efficiently while also cutting your energy bills. Here, we’ll be taking a deeper look at the Tado smart thermostat (a user friendly smart thermostat with multiple impressive features such as a great design, self learning and LED interface).

A Tado smart thermostat is a relatively small piece of kit which is perfect for tech-lovers looking to get a first experience of the smart thermostats’ world. Although the appliance might feature just a basic design with a bit less advanced features in comparison with other thermostats like Hive, Nest and more, it however, still comes with some fantastic features which you can’t afford to miss out on. These includes geofencing, Smartphone or tablet control as well as heat scheduling. As you would have expected with any good smart thermostat, the ability to remotely control your heating is a top priority for several smart thermostats’ owners and Tado offers you this and more. Therefore, no more worries during the Winter months and wishing your home should be warm and perfect for your return. Aside this, a Tado smart thermostat also goes a long way to ensure efficient energy use and as a result, reducing the money paid on energy bills.

Overall, Tado is a nicely designed smart thermostat which is relatively easy to use and a perfect option for homeowners interested in having a taste of the world of smart thermostats or looking to replace their existing device.

Condensing boilers are the in-thing when it comes to modern heating systems in UK homes and across the globe for a good reason. This is primarily due to the fact that condensing boilers happens to be highly efficient as it enables the fuel you’re burning to heat up your home go a lot further. Having a new high efficiency condensing boiler rather than an old G-rated non condensing boiler will not only enhance your heating controls, but also save you a lot of money annually. In this article, we’re going to take you through the basics of a condensing boiler. Let’s take a closer look!

If you’re interested in getting a greener and more efficient boiler, you simply can’t afford to look beyond a high efficiency condensing boiler. This is purely due to the fact that these condensing boilers happens to make a better use of the heat they’re able to produce from burning fuels like oil or gas ( in other words, they require less heat from the burner, which makes them a lot more efficient).

So how does a condensing boiler work? Unlike a non-condensing heat-nly boiler, some heat will be wasted in form of hot gases which are released from the flue. Meanwhile a condensing boiler captures some of the heat from these gases and puts them to use for heating up water that’s coming back from your central heating system. As a result, it requires just a minimal heat from the burner which make the boiler more efficient.

You should take note that all new modern boilers are condensing boilers. Therefore if you’re planning to replace an old boiler with a new one, you’ll definitely be buying a new condensing boiler and benefit from all the efficiency and savings that comes with it.

How Long Does A Boiler Service Take?

Servicing of your boiler is a very crucial activity which does not only help in keeping your heating system in a top condition, but also assists in ensuring the safety of both you and your loved ones. If you carry out a regular boiler service you’ll be able to identify any possible fault your boiler may have on time before it leads to a more serious issue or even a boiler breakdown. As a result, you’ll be able to save yourself some time and money, but more importantly will save you from any dangerous risk that may result from gas leak in a boiler. The best time for a boiler service is in the summer when you’d probably would not really need the system, so you can take advantage of that as well as the possible lower boiler servicing cost during this period.

Before we look into the amount of time a boiler service should take, let’s first consider what should be done during a boiler service.

✓ Visual inspection. This is a check carried out by the heating engineer to ensure your boiler still meet the existing standards and requirements while also looking for any faults.

✓ Removal of boiler casing. There’s the need to ensure everything is working just fine and also to clean the boiler’s interior. These inspections should include the burner, heat exchanger, main injector and spark probe.

✓ Flue check. This involves making sure that there’s no form of obstructions in the flue terminals as also to ensure that the flue is well installed.

✓ Gas pressure check. This involves making sure that the boiler working with the appropriate pressure.

✓ Boiler fired up. This involves checking for any operating issues.

Generally, a boiler service should be completed within 30 minutes, however this time may vary largely depending on the brand and model.

If you’re building a connected home, a smart thermostat allows you to change the temperature in your home. And not only do several smart thermostats come with touch screens and a user friendly interface, but they’re also compatible with Amazon Alexa, Google Assistant and other voice controlled personal assistants. So how does a smart thermostat work? Let’s have a look!

Generally, smart thermostats are connected to the home’s Heating and/or Air Con system via C wire (common wire). Homes that lacks a C wire (especially older homes) will have to install one first before getting a smart thermostat. The C wire is a crucial element in the installation process as it works mainly to wire your smart thermostats into the Boiler system without tampering with the wiring for the other appliances in the house.

The smart thermostats comes with some special temperature setting which you can access by connecting them to your home’s WiFi. These include:

• Mobile Control

Most smart thermostats are specially designed to enable users to control the temperature of their home from the comfort of their couch or car via their unique mobile apps. This feature is just perfect if you particularly like getting the perfect temperature in your home without having to get out of bed.

• Humidity Controls

Although, the humidity of your home can not really be adjusted with a smart thermostat but you can always stay on top of it by monitoring it or setting an alarm on your phone to go off when the humidity changes.

• Geofencing Feature

With a smart thermostat, you can choose the particular times of the day you want it in action. This feature enables you to go on impromptu travels without having to worry about your energy bills - some smart thermostats come with the geotracking feature which determines when you’ve left the house and adjusts the temperature of the home accordingly with your energy usage in mind.

How Much Is A New Oil Boiler?

An oil boiler is a very useful tool for providing both central heating and domestic hot water to a property by burning oil. As a result, they’re simply one of the most common alternative heating methods used in homes throughout the UK. If you’re not connected to the mains gas network, then it’s a no brainer to depend on another fuel for central heating purposes - oil. Therefore, if you’re looking to get a new oil boiler, you’d need to identify the size and price as there are a plethora of models to select from - all coming in a large array of sizes and prices. We’ve put together some important details about the prices to give you a good insight on the amount you’d have to incur to procure a new oil boiler. Let’s have a look!

Generally, gas boilers are less expensive when compared to the oil boilers. You can get a wide range of gas boilers from a starting price of £500 to £600, meanwhile you’d rarely find an oil boiler less than £1000 in the market.

The lowest priced oil boilers are typically priced starting from around £1000, and the best in class oil boilers normally costs more than £3000.

The rule is, the most expensive oil boiler is typically the largest one. So to have an idea, the bigger it is, the more money you’d have to spend. Oil boiler’s size is measured in kilowatts (kw), which showcases its power. To determine the type of oil boiler that best suits your home, the most significant factor would be the size as a bigger home will require a bigger oil boiler. You have an option to choose between the combi, conventional and the system models of oil boiler.