Find a Heating Engineer you can trust in West Molesey.

How Do You Bleed An Oil Boiler?

Bleeding air between the oil supply and an oil fired boiler’s burner is a process that’s often required when the system has run out of oil and the burner has stopped working. Upon refilling the oil tank, the air that has been trapped within the oil pipe when empty has to be freed to ensure that the oil reaches the burner and allows it to start again. So how do you go about the process?

First and foremost, it must be noted that it’s always better to be on the look out for the amount of oil in your fuel tank and get it refilled before it runs out. However, if it does run out, you can take the following steps:

• Identify the burner

The burner is a red plastic cover and it’s usually positioned on the bottom part of the boiler (mostly inside the boiler casing). Once identified, inspect it to see if the lockout button is lit red. If yes, simply unscrew and detach the burner’s red case using a flat head screwdriver.

• Identify the oil pump

You’ll find the oil pump on the burner’s left side which is connected to the flexible oil line. Once done, simply locate the 3 inches long hexagonal stem protruding from the pump and with a small threaded plug screwed into the end. Unscrew the plug in just half a turn ( 180 degrees) with a 4mm Allen Key. At this stage oil will be released, do ensure there’s a cloth or rag underneath the plug to grab the oil freed.

• Press the lockout button

This is the next and final step. However it’s also crucial to note that the burner fan will run for about 12 seconds and discharge some oil from the loosened plug which you can grab with a cloth or rag. Immediately you hear a buzzing sound, use the Allen key to tighten the plug. If enough air has been bled, the system will fire. But if not, then you’ll have to repeat the process again.

Many domestic biomass boilers are no bigger than a standard gas boiler. However, they do require a flue, a feeder and a space to store the fuel. These can be designed to suit many different properties and will fit in lots of homes or a garage or outbuilding.

Your LPG storage tank should have a gauge that shows you how much fuel it has in it. Most LPG suppliers suggest that you arrange a fuel delivery when the level in your tank gets down to about 20%. Make regular checks, particularly in the winter when you will use more, so you know when levels are low.

If you’re interested in deriving maximum benefits from your central heating system while also being a tech-enthusiast, a smart thermostat is just the perfect option as it allows you to control both your boiler and heating system via your mobile device. It also offers a plethora of features which enables you to heat your home more efficiently while also cutting your energy bills. Here, we’ll be taking a deeper look at the Tado smart thermostat (a user friendly smart thermostat with multiple impressive features such as a great design, self learning and LED interface).

A Tado smart thermostat is a relatively small piece of kit which is perfect for tech-lovers looking to get a first experience of the smart thermostats’ world. Although the appliance might feature just a basic design with a bit less advanced features in comparison with other thermostats like Hive, Nest and more, it however, still comes with some fantastic features which you can’t afford to miss out on. These includes geofencing, Smartphone or tablet control as well as heat scheduling. As you would have expected with any good smart thermostat, the ability to remotely control your heating is a top priority for several smart thermostats’ owners and Tado offers you this and more. Therefore, no more worries during the Winter months and wishing your home should be warm and perfect for your return. Aside this, a Tado smart thermostat also goes a long way to ensure efficient energy use and as a result, reducing the money paid on energy bills.

Overall, Tado is a nicely designed smart thermostat which is relatively easy to use and a perfect option for homeowners interested in having a taste of the world of smart thermostats or looking to replace their existing device.

Re-pressurising your boiler means that you allow more water to enter system via the filling loop. It can be easy to re-pressurise your boiler yourself. Always check your manual, but there are some simple steps you can take to restore pressure to your boiler:

1. Switch off your boiler and let it cool completely
2. Make sure both ends of your filling loop are attached
3. Open both valves to allow cold water into the system – you’ll hear it start to move
4. Look out for your pressure gauge to show 1.5 bar
5. Close both valves
6. Switch your boiler back on
7. Undo both ends of your filling loop and remove it. Remember some water might come out, so be ready to catch some spillage!

Biomass boilers will work with existing central heating systems, presuming this is not decades old, whether they use radiators or under floor heating. A surveyor will check the existing system you have in place before quoting for or recommending a biomass boiler to you.

No. You must never repair your own boiler – only a Gas Safe-registered engineer can do any work on your boiler. You can do simple DIY tasks to repressurise your boiler or stop a leak, but if you have to remove the outer casing of the boiler or touch the flue then you must get a qualified boiler engineer to take a look at your central heating system.

To ensure that your boiler is safe and operating efficiently, it’s essential to have it serviced on a regular basis.

Generally, a boiler service will deliver a wide array of benefits which includes the opportunity to identify safety issues like a possible leak of carbon monoxide, efficient use of energy and reduction in energy bills, prevention of breakdowns, a valid warranty when the boiler is serviced regularly by a qualified engineer as well as an extended lifespan. So what exactly does a boiler service cover? This guide will give you a good insight as to what happens during that service.

Before we get started, it’s very important to note that the work done is always as good as the engineer you employ. Therefore, it’s advisable to make sure your preferred engineer is qualified before proceeding with the service. Below are some of the basic practices the engineer may perform during their visit.

• Thorough Inspection

During the visit, the engineer will carry out a detailed examination of your boiler to ensure it still meets the current standards while also making sure that there are no leaks or corrosion. What’s more? They’ll also examine the boiler’s flame for any faults.

• Boiler Casing Removal

The boiler casing will be detached to check all components and ensure they’re free from all forms of dirt and see to it that they’re all working just as they should. This will include examination of the heat exchanger, main injector, burner and spark probe.

• Flue Examination

The engineer will inspect the flue terminals to make sure there are no form of obstructions and it’s also safely installed.

• Gas Pressure Examination

This is done to make sure the heating system is operating at the right pressure.