Find a Heating Engineer you can trust in Kingswinford.

How Do You Bleed An Oil Boiler?

Bleeding air between the oil supply and an oil fired boiler’s burner is a process that’s often required when the system has run out of oil and the burner has stopped working. Upon refilling the oil tank, the air that has been trapped within the oil pipe when empty has to be freed to ensure that the oil reaches the burner and allows it to start again. So how do you go about the process?

First and foremost, it must be noted that it’s always better to be on the look out for the amount of oil in your fuel tank and get it refilled before it runs out. However, if it does run out, you can take the following steps:

• Identify the burner

The burner is a red plastic cover and it’s usually positioned on the bottom part of the boiler (mostly inside the boiler casing). Once identified, inspect it to see if the lockout button is lit red. If yes, simply unscrew and detach the burner’s red case using a flat head screwdriver.

• Identify the oil pump

You’ll find the oil pump on the burner’s left side which is connected to the flexible oil line. Once done, simply locate the 3 inches long hexagonal stem protruding from the pump and with a small threaded plug screwed into the end. Unscrew the plug in just half a turn ( 180 degrees) with a 4mm Allen Key. At this stage oil will be released, do ensure there’s a cloth or rag underneath the plug to grab the oil freed.

• Press the lockout button

This is the next and final step. However it’s also crucial to note that the burner fan will run for about 12 seconds and discharge some oil from the loosened plug which you can grab with a cloth or rag. Immediately you hear a buzzing sound, use the Allen key to tighten the plug. If enough air has been bled, the system will fire. But if not, then you’ll have to repeat the process again.

If you choose to install an LPG boiler, you’ll need to find an LPG supplier. They’ll deliver fuel to you every time your storage tank runs low. You can even rent a storage tank from them if you don’t want to buy one. Make sure you know who your local suppliers are and where they are based.

If you’re interested in deriving maximum benefits from your central heating system while also being a tech-enthusiast, a smart thermostat is just the perfect option as it allows you to control both your boiler and heating system via your mobile device. It also offers a plethora of features which enables you to heat your home more efficiently while also cutting your energy bills. Here, we’ll be taking a deeper look at the Tado smart thermostat (a user friendly smart thermostat with multiple impressive features such as a great design, self learning and LED interface).

A Tado smart thermostat is a relatively small piece of kit which is perfect for tech-lovers looking to get a first experience of the smart thermostats’ world. Although the appliance might feature just a basic design with a bit less advanced features in comparison with other thermostats like Hive, Nest and more, it however, still comes with some fantastic features which you can’t afford to miss out on. These includes geofencing, Smartphone or tablet control as well as heat scheduling. As you would have expected with any good smart thermostat, the ability to remotely control your heating is a top priority for several smart thermostats’ owners and Tado offers you this and more. Therefore, no more worries during the Winter months and wishing your home should be warm and perfect for your return. Aside this, a Tado smart thermostat also goes a long way to ensure efficient energy use and as a result, reducing the money paid on energy bills.

Overall, Tado is a nicely designed smart thermostat which is relatively easy to use and a perfect option for homeowners interested in having a taste of the world of smart thermostats or looking to replace their existing device.

When it comes to gas boilers, this is one of the most frequent questions that always pops up and for a good reason. When you invest a considerable amount of money to acquire and install a gas boiler in your home or property, it’s only reasonable not only to expect the boiler to warm up your home efficiently, but also to do so for a long period of time. If you’ve just bought or about to get a new gas boiler, it’s likely you won’t have to worry about getting a replacement for a lengthy period of time. Several gas boilers will last for anywhere between 10 to 15 years on the average. However in the event whereby you have an existing one that’s fast approaching the end of it’s useful life, then you should know the time go get a new gas boiler is just around the corner, and the earlier you make the purchase, the better (to avoid any surprise breakdowns that’ll leave your home super uncomfortable).

Just like any other home appliance, it’s a fact that an older gas boiler ( especially those that have been installed over a decade ago) are significantly less efficient that the new modern ones. When the older versions were manufactured is a completely different time to now as both technology and climate concerns are wide apart. So when your existing boiler is approaching the end of it’s useful life, it’ll be wise to start saving up to cover the cost of getting a new one. However, if it’s only about 5 years ago your boiler was installed, it’s highly likely to still be very efficient.

How To Install A Gas Cooktop In An Island

Are you thinking about installing a gas cooktop in your kitchen island? If yes, then you must know that there are clearance requirements that must be met (before you proceed) between the cut out and the countertop’s edge. Basically, there are incremental requirements for island installation due to the fact that it does not make an assumption that the product is going to be fitted against a rear wall that acts to protect the back of the unit. As a result, while doing an island install we must put the safety of the product into consideration much more that we do a standard install. What’s more? This island clearance requirement develops from a third-party agency and is a standard with all brands. So how do you install a gas cooktop in an island having the aforementioned requirements in mind?

• Use a foil tape to line the inside edges of the cut out. The function of this is to prevent heat damage as well as countertop’s discolouration. Put the cooktop top on a secured surface.

• Identify the pipe coming out of the cooktop’s side or bottom and brush onto the threads of the manifold entrance.

• Pass the pressure regulator onto the entrance of the manifold and make use of a wrench to tighten it.

• Brush the pipe joint compound onto one of the flare union adaptor’s threads and pass it into the regulator’s open end. Make it slightly tight with a full turn of the wrench.

• Connect the flare union adaptor’s open end with the flexible appliance connector hose, upon brushing on pipe joint compound.

• Put foam tape on the cooktop underside’s edges, if your cooktop comes with a glass burner plate.

• Turn the cooktop to set it into the cutout.

• Apply pipe-joint compound onto the flare union adaptor left and secure it firmly into the gas shutout valve.

• Connect the flexible hose connector’s free end with the flare union adaptor.

How Much Is A New Oil Boiler?

An oil boiler is a very useful tool for providing both central heating and domestic hot water to a property by burning oil. As a result, they’re simply one of the most common alternative heating methods used in homes throughout the UK. If you’re not connected to the mains gas network, then it’s a no brainer to depend on another fuel for central heating purposes - oil. Therefore, if you’re looking to get a new oil boiler, you’d need to identify the size and price as there are a plethora of models to select from - all coming in a large array of sizes and prices. We’ve put together some important details about the prices to give you a good insight on the amount you’d have to incur to procure a new oil boiler. Let’s have a look!

Generally, gas boilers are less expensive when compared to the oil boilers. You can get a wide range of gas boilers from a starting price of £500 to £600, meanwhile you’d rarely find an oil boiler less than £1000 in the market.

The lowest priced oil boilers are typically priced starting from around £1000, and the best in class oil boilers normally costs more than £3000.

The rule is, the most expensive oil boiler is typically the largest one. So to have an idea, the bigger it is, the more money you’d have to spend. Oil boiler’s size is measured in kilowatts (kw), which showcases its power. To determine the type of oil boiler that best suits your home, the most significant factor would be the size as a bigger home will require a bigger oil boiler. You have an option to choose between the combi, conventional and the system models of oil boiler.

First and foremost, the purpose of a landlord insurance is simple and pretty straightforward. It protects against risks associated with your rental property as well as activity. Most policies start out with building insurance as well as property owners’ liability insurance but you’re absolutely free to include several other covers. These covers can include tenant default or accidental damage, loss of rent and more depending on your needs. It’s important to note that varying types of landlord insurance provides coverage for different sorts of risks. For instance, building insurance provides coverage for the cost of repairing or rebuilding your property, while contents insurance provides coverage for contents if they’re damaged or stolen. However, the question is, does landlord insurance cover boiler? In this post, we’re going to shed more light into this to help you make informed decisions moving forward. Let’s take a look!

The short and simple answer to this question is yes, landlord insurance can definitely cover boiler break down! However, this is usually possible only if you select this option when you purchase your landlord insurance policy. With some boiler cover providers, you’ll have to include a home emergency cover to your landlord insurance so as to cover any form of boiler break down. Once this is done, if the boiler in your rental property starts to malfunction or stops functioning, a Gas Safe registered engineer would be sent to your premises to help out with the situation. With this, the repairing cost of your heating system would be covered by the insurance excluding any excess and up to the limit of your policy.

The size of boiler you need will depend on the size of your commercial property, how many radiators and bathrooms you have and how appliances willl need hot water at the same time. The boiler size refers to its output, which is measured in kilowatts (kW), rather than the actual dimensions. Speak to your boiler engineer about which boiler is suitable for you, as if you have more than one bathroom or a lot of people in your home a combi boiler might not suit you.