Find a Heating Engineer you can trust in Horsham.

Are Electric Radiators Expensive To Run?

Just like many home additions, the running costs of electric radiators varies largely on a number of factors. Great number of electric radiators typically comes with an in built thermostat which is designed to turn itself off automatically when not in use in order to save energy.

However the energy provider’s set electricity charge tariff will also have a great influence on an electric radiator’s running cost. Let’s take a look at the running costs of an electric radiator!

A 600 Watt electric radiator ( on a standard electricity tariff) will usually have a running cost ranging between 4 to 6 pence each hour. However you should also take note that this scenario might change in situations whereby the electric radiator is not calling for heat the full 60 minutes of each hour. And this is more likely to be the situation as the thermostat is programmed in such a way that enables it to turn itself off immediately there’s an achievement of your required room temperature level - usually within 10 minutes from the time it was switched on. As a result of this, the running cost per hour of electric radiators will be greatly reduced to just about 1 to 2 pence.

It’s also important to note that enhancing the insulation of your home can go a long way to add to the heat retention value of each room. Consequently, the duration at which the electric radiator calls more heating will be significantly reduced, which in turn, implies a lower electricity bill.

Another key factor that can play a huge role in saving on your heating bills is the programming as well as usage of your electric radiators. Every radiator comes with an independent digital thermostat with a number of 24/7 programming options to help achieve maximum efficiency. When the radiator is properly set according to your lifestyle, you can save as much as 50 percent on your heating bills.

If you’re thinking about getting a new gas boiler for your home or property, then you might also be wondering how much it’ll cost you so you can set a budget and start planning. As simple as this question sounds, it’s actually very tricky to provide a simple and short answer as the costs of installing a new gas boiler alone varies greatly based on the parts needed, the amount of work required, your location, their availability as well as the company you hire for the project.

When it comes to purchasing a new gas boiler the price you’re expected to pay also depends on multiple influencing factors such as the type, brand as well as your most preferred gas boiler model. However, one thing you should have in mind is the fact that your gas boiler is right at the heart of your home or property and can be a complicated piece of machinery. As a result, you wouldn’t expect gas boilers to come cheap. Generally, it’s going to cost within the range of £500 to about £2,500 to get a new gas boiler. Therefore, it’s always advisable to obtain all necessary details and facts before you decide to purchase a replacement gas boiler.

This price range may seem too high as it’s usually a turn off for most homeowners. However, it’s worth noting that gas boiler replacement costs and gas boiler installation costs are, more often than not, compensated by the saving you’ll make off your utility bills - all thanks to the new and more energy efficient boiler you just installed in your home. And even more importantly, when it has been estimated that roughly half of the amount spent on energy on an annual basis depends on your boiler.

Biomass boilers will work with existing central heating systems, presuming this is not decades old, whether they use radiators or under floor heating. A surveyor will check the existing system you have in place before quoting for or recommending a biomass boiler to you.

During a boiler service, your boiler engineer will perform a series of checks to ensure that your boiler is safe and efficient. First, they will conduct a visual inspection to check for any corrosion or leaks. They will also check the flame in your boiler. They’ll then remove the boiler casing and check all the components, including the heat exchanger, burner and spark probe, then clean the inside. After this, they’ll check the flue for obstructions and ensure that it’s safely fitted. They will then do a gas pressure check to ensure the boiler is working at the right pressure, before firing it up to check for any working faults.

If you choose to install an LPG boiler, you’ll need to find an LPG supplier. They’ll deliver fuel to you every time your storage tank runs low. You can even rent a storage tank from them if you don’t want to buy one. Make sure you know who your local suppliers are and where they are based.

Re-pressurising your boiler means that you allow more water to enter system via the filling loop. It can be easy to re-pressurise your boiler yourself. Always check your manual, but there are some simple steps you can take to restore pressure to your boiler:

• Switch off your boiler and let it cool completely

• Make sure both ends of your filling loop are attached

• Open both valves to allow cold water into the system – you’ll hear it start to move

• Look out for your pressure gauge to show 1.5 bar

• Close both valves

• Switch your boiler back on

• Undo both ends of your filling loop and remove it. Remember some water might come out, so be ready to catch some spillage!

How Long Does A Boiler Service Take?

Servicing of your boiler is a very crucial activity which does not only help in keeping your heating system in a top condition, but also assists in ensuring the safety of both you and your loved ones. If you carry out a regular boiler service you’ll be able to identify any possible fault your boiler may have on time before it leads to a more serious issue or even a boiler breakdown. As a result, you’ll be able to save yourself some time and money, but more importantly will save you from any dangerous risk that may result from gas leak in a boiler. The best time for a boiler service is in the summer when you’d probably would not really need the system, so you can take advantage of that as well as the possible lower boiler servicing cost during this period.

Before we look into the amount of time a boiler service should take, let’s first consider what should be done during a boiler service.

✓ Visual inspection. This is a check carried out by the heating engineer to ensure your boiler still meet the existing standards and requirements while also looking for any faults.

✓ Removal of boiler casing. There’s the need to ensure everything is working just fine and also to clean the boiler’s interior. These inspections should include the burner, heat exchanger, main injector and spark probe.

✓ Flue check. This involves making sure that there’s no form of obstructions in the flue terminals as also to ensure that the flue is well installed.

✓ Gas pressure check. This involves making sure that the boiler working with the appropriate pressure.

✓ Boiler fired up. This involves checking for any operating issues.

Generally, a boiler service should be completed within 30 minutes, however this time may vary largely depending on the brand and model.

How To Install An Oil Boiler Heating System

Just like several other skills, the installation of an oil boiler heating system can be a challenge. It requires enough persistence to actually get right, so if you’re the type with little patience, we’d recommend you hire the services of a professional oil boiler heating system fitter who can guarantee the best results and save you time and extra money due to potential damages.

To install your boiler system yourself, it’s always advisable to start by getting the information on the best installation processes from the supplying company which will go a long way to save you from future headaches. However, we’ve put together this guide to give you a basic knowledge on how its done. Let’s have a look!

lRead Instruction Manual

• Carefully read and digest the instruction manual thoroughly.

• Make sure you understand the installation diagrams

• Spread out the materials and get familiar with them.

lFigure Out What Goes Where

• Take your time to determine where everything goes in relation to the others.

• Identify the new radiator’s position.

• Get sufficient sealants to prevent possible leakages inside the walls.

lIdentify The Pipe Routes

• Determine the pipe routes while fitting the new radiators

lInstall The Boiler

• Turn off water and all electrics

• Fit the boiler into the wall

• Make sure the fittings are secured.

lInstall The Radiator

• The effectiveness of your home’s heating system is as good as the radiators you incorporate and how good they’re installed.

• You may have to utilize extra radiators in large open plan kitchens and living rooms (for effective heating).

lOffer Ventilation

• Once you’ve successfully installed the new radiator, a small dose of air ventilation would be needed.

• Turn the key of each valve located at the bottom, do not stop until a little amount of water spills over the top of the unit.