Find an Insulation Installer you can trust in Hook.

In general, you won’t need planning permission to install soundproofing. If you are installing soundproofing against a shared wall, you will usually need to follow the rules and restrictions set out in the Party Wall Act. In listed buildings and conservation areas, there may be extra restrictions on soundproofing.

Do you know about 25 percent of heat that escapes from an uninsulated house are lost through the roof? Fortunately, roof insulation is something that can done by all DIYers irrespective of their experience levels. However, if you happen to lack the confidence necessary to pull off this, then it’s strongly recommended that you hire the services of a professional who can guarantee the best results and also save you time and money that could arise from potential cost mistakes. Let’s take a look!

• Clear out all clutter. This involves taking out all the rubbish and clutter from the loft. In order to work effectively, you’ll need a totally clear and empty loft space.
• Ensure that there’s sufficient insulation. The importance of a good ventilation cannot be overstated. Poor ventilation will result in forming of condensation and this condensation can make the roof timbers rot and compromise the structural integrity of the entire roof. If there are no roof windows which is the easiest way to provide a loft ventilation, the next best option would be to follow the loft floor along to the point where the roof comes down to meet it. There should be a gap at this point, also referred to as the eaves, between the outside wall and the underside of the roof.
• Measure your loft area. Take a measurement of the loft space in order to calculate the amount of insulation as well as the type you need. If you’re not sure, always get more that it’s required as skimming on the amount you use will only back fire in form of increased energy costs
• Check for water pipes.

To get started, simply make sure all cracks and gaps in the ceiling are filled using a standard filler or decorator caulk. Once done, clean the gaps in the joists and even to the point of hovering all the dust up. Finally,check for the hazards that can cause you problems before laying the loft insulation.

More often than not, several homeowners fail to realize there’s so much value sitting right under their roof - the loft. When a loft is insulated, there are so many juicy benefits that can be derived. It can go a long way to save increase you energy savings and several more functions. Therefore, if you really wish to maximize the space under your home’s roof, you’d have to considering insulating it. So how much would it cost to have your loft insulated? Here, you’ll discover the cost of insulating your lofts so you that you can set a budget and start to plan.

The cost of insulating a loft is actually affordable for several individuals, however, this depends on a wide range of factors such as the size of the house as well as the type of insulation being installed. One significant factor is the insulating material that you choose to install. If done properly, you’d be able to prevent heat from escaping through the roof of the house which helps improve energy efficiency and ultimately, save you some money on heating bills.

If you’d prefer to make it a DIY project and you go for a blanket insulation it costs about £5 per m2. therefore, this will cost within the range of £100 to about £150 for a small home.

For a professional service, you’ll be provided with a quote for both the materials and labour. The amount will be based on the number of insulation required, the company hired, your location as well as the method selected. The price to purchase and install blanket insulation  would be between the range of £300 to £400 depending on the size of your home.

Insulating your loft roof comes with a wide range of benefits. Not only do you get to maintain a comfortable temperature in your house for longer, but you’ll also get to cut down on your heating bills. If you wish to insulate your loft roof, you’ve come to the right place! This process can be very tedious and time consuming especially if you don’t what you’re doing or lack the required confidence to pull it off. It’s advisable to hire the services of a reputable professional who can guarantee the best results for help and also save you some time and money that can come from potentially costly errors.

Before you start rolling out, you’d have to make sure that all cracks, gaps and holes in the ceiling are filled with either a standard filler or decorators caulk. You can also clean between between the gaps in the joists thoroughly. And finally, check for hazards that can cause you problems before getting stated.

• Remember to leave ventilation gaps as you start from the eaves. Then work towards the loft’s centre, starting from the point furthest from the hatch.
• Lay the first layer between the joists which should be 100 mm and then the subsequent layer should be 170 mm to make it up to the recommended 270 mm.
• Carry the electric cables above the insulation and work around visible light fittings.
• Cut the roll in the centre of the floor when rolling out from the eaves on both sides with the help of a craft knife. Ensure that there are no gaps between the insulation and the joists’ edges.
• Lag pipes as you go in order to prevent walking over the insulation to get back to them.
• Ensure that the loft is totally insulated
• Insulate the hatch.

With the title of this blog, do not be deceived into thinking the purpose is to encourage you to install an external insulation by yourself. Even as a competent DIYer, it’s not advisable to buy a couple of materials and start slapping it into the wall hoping for the best outcome. External insulation is by no means a DIY job and without the proper training and experience, it can easily turn out disastrous resulting in loss of time, effort and money in such a valuable project. This blog, however, will give you a great insight on how the installation process works and help maximize knowledge ensuring you do not spend more than necessary.

External Insulation Installation

lRender Test

• This is done to ensure the existing render is good enough for insulation support.

• If positive, the insulation can be applied directly onto it.

• If negative, ensure removal of the old render before fitting the insulation.

lPipework Adjustment & Removal

• Remove all pipework prior to insulation fitting

• Install temporary downpipes to ensure water is not wasted and everything continue to function normally during the insulation fitting process.

lWindow Protection

• Protect the window with a protective layer or film.

lStarter Track Fitting

• Determine level you want the insulation to start (height).

• Fit the aluminium start track or carrier tray at the identified level.

lInsulation Boards Fitting

• Apply a layer of adhesive to the board and glue them to the wall in a staggered pattern.

• Cut to fit round all obstructions and windows.

• File off the edge of the board where necessary using a rasp upon successful fitting of the boards

lMechanical Fixing Inclusion

• Hammer around 10 fixings per square metre into the board.

• This is to secure the insulation boards.

lBeading Fitting

• Add corner beads and stop beads to ensure the insulation is secure and to prevent it from making contact with other materials.

lReinforcing Mesh & Render Addition

• Apply two layers of strengthening properties and between the two layers of render, include a fibre glass mesh.

lPrimer Application

• Paint on the primer

lFinal Render Application

• Choose your most preferred texture and colour as this will be the last coating of the installation process.

lPipework Re-installation

• Re-install all detached pipework at the start of the installation process.

With the numerous benefits that comes with the installation of an external wall insulation in a building, it’s also important to find out whether it’s also safe before proceeding to fit one in your home. Firstly, to ensure that external wall insulation systems are safe, they must be BBA approved, which means they’ve been subjected to a thorough testing by the British Board of Agrement and therefore, suitable for use in UK homes.

Given the fact that cladding materials have recently generated a lot of debate and negative press about how reliable some particular materials are, questions are being asked of the safety and reliability of external wall insulation. However we must clarify that, although external wall insulation can be classified under cladding, it is very different to rainscreen cladding - which caused the Grenfell fire tragedy.

External wall insulation is completely safe. However, when it comes to fire, the safety of your system depends largely on the insulation type in question. The safest type of insulation you can have installed is the Rockwool insulation boards which are rated as Euroclass A1 non-combustible. The board is specially designed in such a way that it contains fire - preventing it from reaching the other areas of the building. They also do not produce harmful emission or smoke when impacted by fire.

Meanwhile, the Wood Fibre, is also a great insulation which is known to char and not burn. Contrary to many beliefs, it actually burns slowly creating this charring effect which produces an oxygen barrier that helps reduce the spread of fire.

To make your system safer, you can also make use of Fibreglass Mesh for reinforcement. It helps to improve the strength of the tensile which promotes the security of the boards attached to the wall.

A lot of an uninsulated property’s heat is lost through the roof and that’s even more alarming, when you realize this figure is up to a quarter of the total heat of the house. Hence, the tremendous importance of preventing this heat loss through loft insulation which will go a long way to help you against spending unnecessary thousands of pounds on heating bill as well as energy loss.

Loft insulation is an effective method to achieve the desired result, however the question is, how exactly does it work? Well, it’s time to find out!

Using either a fireplace or central heating to heat up your home, a large quantity of that heat would be lost through the roof of your home. Generally, heat rises and when it does, there’s simply no way to prevent it - it’s just science. Escaping by both the conduction and convection methods via your roof, the heat escaping through your ceiling, into the loft space and out into the open air outside can only be significantly reduced by laying loft insulation.

Generally, the added layer of insulation works by trapping the heat inside the room below the loft so as to enable the air within your house to stay warmer for longer. What’s more? The layer of insulation also keeps cold air from the outside from entering your home. As a result, you don’t have to heat your home as much in order to achieve the same temperature for each individual room. Over time, just by doing this you can potentially save hundreds pounds. Getting it installed in your home may actually seem a bit expensive at first, but it’s something that’ll eventually pay off.

The short and simple answer to this question is yes, loft insulation does cause condensation. Over the years, problems with condensation in loft spaces have become increasingly common. While this may not be harmful in anyway, when the condensation becomes excessive it can lead to more serious issues taking root in your loft like wet rot, dry rot as well as black spot mould. Generally, the best thing to do if you’re concerned about the condensation in your loft space and that it may rapidly become a bigger problem is to get in touch with a damp specialist as soon as possible.

Even though insulating your loft space comes with a wide array of benefits like making the top floor rooms warmer, it’s however comes at the cost of making your loft or room space cooler. Condensation in lofts take place primarily due to the humid air making its way through insulation or other gaps into the loft space and touching a cooler surface which in turn results in beads of moisture on the timbers, lintels as well as the underside of the roof. This is why its always a great idea make use of thermal insulation with a vapour barrier that’s installed on the warmer side of the insulating material.

Condensation in loft is caused by excess moisture in the air and lack of adequate air ventilation. Here are some top reasons that gives rise to this in the loft:

• Extra insulation has been installed in the loft leading to a restriction on the natural air circulation in the property.
• When the storage boxes or other items that has been stockpiled in the loft blocks the roof vents.
• The release of steam and moist air into the loft space by hot water tanks.