Find an Insulation Installer you can trust in Gourock.

Insulating your loft roof comes with a wide range of benefits. Not only do you get to maintain a comfortable temperature in your house for longer, but you’ll also get to cut down on your heating bills. If you wish to insulate your loft roof, you’ve come to the right place! This process can be very tedious and time consuming especially if you don’t what you’re doing or lack the required confidence to pull it off. It’s advisable to hire the services of a reputable professional who can guarantee the best results for help and also save you some time and money that can come from potentially costly errors.

Before you start rolling out, you’d have to make sure that all cracks, gaps and holes in the ceiling are filled with either a standard filler or decorators caulk. You can also clean between between the gaps in the joists thoroughly. And finally, check for hazards that can cause you problems before getting stated.

• Remember to leave ventilation gaps as you start from the eaves. Then work towards the loft’s centre, starting from the point furthest from the hatch.
• Lay the first layer between the joists which should be 100 mm and then the subsequent layer should be 170 mm to make it up to the recommended 270 mm.
• Carry the electric cables above the insulation and work around visible light fittings.
• Cut the roll in the centre of the floor when rolling out from the eaves on both sides with the help of a craft knife. Ensure that there are no gaps between the insulation and the joists’ edges.
• Lag pipes as you go in order to prevent walking over the insulation to get back to them.
• Ensure that the loft is totally insulated
• Insulate the hatch.

This depends on the amount of insulation already present in your property. However, adding insulation has been proven to improve the energy efficiency of your home and decrease your heating bills, this is more obvious in older properties or where single glazing is still in situ.

With the numerous benefits that comes with the installation of an external wall insulation in a building, it’s also important to find out whether it’s also safe before proceeding to fit one in your home. Firstly, to ensure that external wall insulation systems are safe, they must be BBA approved, which means they’ve been subjected to a thorough testing by the British Board of Agrement and therefore, suitable for use in UK homes.

Given the fact that cladding materials have recently generated a lot of debate and negative press about how reliable some particular materials are, questions are being asked of the safety and reliability of external wall insulation. However we must clarify that, although external wall insulation can be classified under cladding, it is very different to rainscreen cladding - which caused the Grenfell fire tragedy.

External wall insulation is completely safe. However, when it comes to fire, the safety of your system depends largely on the insulation type in question. The safest type of insulation you can have installed is the Rockwool insulation boards which are rated as Euroclass A1 non-combustible. The board is specially designed in such a way that it contains fire - preventing it from reaching the other areas of the building. They also do not produce harmful emission or smoke when impacted by fire.

Meanwhile, the Wood Fibre, is also a great insulation which is known to char and not burn. Contrary to many beliefs, it actually burns slowly creating this charring effect which produces an oxygen barrier that helps reduce the spread of fire.

To make your system safer, you can also make use of Fibreglass Mesh for reinforcement. It helps to improve the strength of the tensile which promotes the security of the boards attached to the wall.

External wall insulation works to keep your home cosy and comfy while also helping to cut the energy bills. However with the great benefits also comes great costs, so it’s actually a logical decision to know whether there are grants out there which you’re eligible for to help you handle the cost of the external wall insulation.

There are grants available for external wall insulation, but rarely will you find one that covers the full installation cost. With the help of the government’s Energy Company Obligation (ECO) scheme, a couple of energy companies assist in making your home more energy efficient by offering grants or free insulation. In certain cases whereby you receive particular state benefits, you may as well qualify for a higher grant that’ll cover more of the insulation cost.

However, if your energy supplier doesn’t offer any grant, you need not worry as you can save as much on energy bill after installation. Here’s what insulation can help you save per year on energy bills:

• Floor insulation can help you save within a range of £30 to £75 each year.

• Cavity wall insulation can help you save about £85 to £280 a year.

• Loft Insulation (270mm) can help you save about £135 to £250 a year.

Generally, the amount you’ll be able to save on your energy bills depends mainly on the type and size of your property, as well as how energy efficient it already is without the insulation. In the long run, your external wall insulation will more than give you back your investment on the valuable project through your savings on energy bills. In other words, whether or not you’re eligible for a grant should never stop you from installing an external wall insulation.

Over the years there has been an increase in the recommended thickness of loft insulation by the government. Obviously, the reason behind this is pretty simply - the thicker the layer of your loft insulation the bigger your savings. The UK government is very keen to every house in the country to have loft insulation fitted where possible as it helps to minimize the heating demands of these properties. Households get to benefit from loft insulation in so many ways which includes reduced energy energy bills as well as having a home that stays at a more comfortable temperature for longer.

Generally, for the government energy efficiency is crucial as it implies that the highest demand ( which is usually the time of the day when gas or electricity use is at its peak ) reduces, since each building requires slightly less energy. Overall, that ultimately implies that new power plants don’t have to be built which is some nice cost savings for the government.

In the 1980’s, any thickness of loft insulation from 25 mm to 50 mm was considered the standard. But then, building regulations stated that homes should have as much as 100 mm of loft insulation. Over time, this gradually increased to 270mm for new builds and also recommended for other properties, although not essential. As a result of this, there’s always a need to check how much insulation you currently have in your loft before you decide to purchase more. You may discover that you already have something within the range of 20 mm to 200 mm up there and knowing this and the insulation values will assist in determining how much more you’ll need to purchase, if any at all. You should also note that some modern materials can offer the same thermal insulation whilst not being as thick.

Do you know about 25 percent of heat that escapes from an uninsulated house are lost through the roof? Fortunately, roof insulation is something that can done by all DIYers irrespective of their experience levels. However, if you happen to lack the confidence necessary to pull off this, then it’s strongly recommended that you hire the services of a professional who can guarantee the best results and also save you time and money that could arise from potential cost mistakes. Let’s take a look!

• Clear out all clutter. This involves taking out all the rubbish and clutter from the loft. In order to work effectively, you’ll need a totally clear and empty loft space.
• Ensure that there’s sufficient insulation. The importance of a good ventilation cannot be overstated. Poor ventilation will result in forming of condensation and this condensation can make the roof timbers rot and compromise the structural integrity of the entire roof. If there are no roof windows which is the easiest way to provide a loft ventilation, the next best option would be to follow the loft floor along to the point where the roof comes down to meet it. There should be a gap at this point, also referred to as the eaves, between the outside wall and the underside of the roof.
• Measure your loft area. Take a measurement of the loft space in order to calculate the amount of insulation as well as the type you need. If you’re not sure, always get more that it’s required as skimming on the amount you use will only back fire in form of increased energy costs
• Check for water pipes.

To get started, simply make sure all cracks and gaps in the ceiling are filled using a standard filler or decorator caulk. Once done, clean the gaps in the joists and even to the point of hovering all the dust up. Finally,check for the hazards that can cause you problems before laying the loft insulation.

If you have a loft, then the next thing that’s crucial is a loft insulation. Asides from cutting down on your carbon footprint, when you’re able to install an effective loft insulation you can slash your heating bills by up to £250 per year. What’s more? Besides making your home more energy efficient, it can also increase the value of your property a great deal. So if you’re also considering the insulation of your loft, one of the few things that comes to mind is, what loft insulation is the best to incorporate? In order to help you make the best informed decision possible, this post is going to address this issue and put you on the right path.

In truth, there’s no way to say exactly which type of insulation is the best as all types usually have a different purpose as well as usage. The insulation you choose for your home’s loft is be based largely on the how you’re going to make use of the space as well as any unique challenges you might face given the shape of your home’s loft. Below are some types of insulation to give you a better idea:

• Blanket insulation. This is the most common type that comes in rolls of rock, glass or mineral fibre ( or foil-backed felt ). It normally the most affordable and also a good all-purpose insulation which is easy to fit although not suitable for the roof.
• Loose-fill insulation. This type of insulation features a loose, lightweight material such as cork granules, cellulose fibre, mineral wool etc. It can either be incorporated as a top up or on its own. The primary drawback is it isn’t very secure and can also be very messy.
• Sheet insulation. This is the best solution for the roof’s underside as it offers a highly effective insulation for your loft space and can also be decorated over. The drawback here is that it’s usually the most expensive type to purchase and install.

With cavity walls being very similar to other type of brick works, it can be quite confusing to figure out the type of wall your property possesses. If your house was constructed after the 1920s, then its highly likely the you have cavity walls, while older houses (houses before the 1920s) are likely to have solid walls. What’s more? If you happen to own a home that was built in the last decade, then it’s very possible that it was built with insulation installed during construction.

An effective way to determine whether or not your property is built with cavity wall is to examine the brickwork on your home’s exterior. The bricks will typically possess a regular pattern if it features cavity walls. In the event whereby the brick work is covered by render, you can also figure it out by taking a measurement of the wall’s width. If the brick wall is beyond 3000mm in thickness ( from the exterior wall to the interior wall), then it probably features a cavity. Meanwhile, a wall that’s narrower is very likely to be solid. Stone walls, on the other hand, may actually be thicker but are most times solid.

In a situation whereby your house is built using steel frame or timber frame, or made using pre-fabricated concrete, there are varying rules that applies when it comes to insulation and should be examined by an expert before any insulation is installed. More often than not, most contractors will have installed special air vents, which can also be a good indicator that a cavity wall insulation has been done.