Find a Landscaper you can trust in Stonehaven.

There is a variety of methods available to ensure that your paving drains properly, for example draining into a lawn or soakaway. Correct drainage of paving is a requirement for planning permission. See our guide on planning permission for paving for more information.

Our gardens are often our pride and joy, so we want them to look their best. If you notice that your garden is uneven, you’ll probably want to do something about it. But how do you level your garden or lawn? A gardener can help you do this and will get the best finish, but if you want to have a go at doing it yourself there are a few steps you can take. Before you start, make sure you’ve got all the following equipment to hand:

• String line
• 4 rods & string
• Tape measure
• Flat shovel
• Water sprinkler or watering can
• A rake
• Earthmoving and compacting equipment
• Spirit level
• 2 x 4 piece of wood
• Wheelbarrow
• Protective gloves and shoes

Then, you can get ready to level your garden.

1. Mark out the area Push 4 rods into the ground around the area you want to level out in a square or rectangle. Tie your string around the rods to connect them all together, ensuring that the string stays tight. Then use your string line to any of the 4 sides to check that it’s level. You’ll then need to measure the height from the ground to the string on all four sides to check how much you would need to adjust the ground to make it level. Make sure you take note of the high and low spots and measure the difference between these spots.
2. Water the ground to soften it If you want to level your lawn, or the part of your garden that you want to level has grass on it, you’ll need to uproot the ground underneath it. To make it easier to dig and lift out the grass, sprinkle some water over the area before you begin. It’s a good idea to do this over a few days to really soften it – but make sure you don’t do it so much that it becomes too heavy and soggy.
3. Remove the grass Push your flat shovel into the ground, around 3-6cm deep, then slide the shovel horizontally to lift out the soil and the grass on top. As you repeat this process around the entire area, make sure you try to lift out the soil evenly to avoid making your levelling task even harder.
4. Add soil Fill low spots with nutrient-rich soil and spread evenly over the area with a rake. If you’re levelling out a large area of your garden, consider renting earthmoving equipment to make it easier.
5. Flatten the soil Next you’ll want to compact the soil to protect it from erosion. If you’re working on a small garden or area of your garden, simply use your feet – get stomping on that ground! You could also use a rake, but for larger gardens consider hiring a compactor. Then, leave the soil to settle for around 3 weeks before doing anything. If you’re doing this in the summer, you can water it sparingly to keep it from drying out.
6. Adjust until you’re happy It might take you a few adjustments to get the level of your garden or lawn right. Use a spirit level along a long 2 x 4 piece of wood to see whether the ground is even, then adjust by adding a little more soil or removing soil until it’s at the level you want it.

That’s it. A gardener or landscaping company will be able to level your garden or lawn perfectly, so consider getting some quotes from local companies.

• Decking joists
• Coach screws
• Coach bolts
• Combi drill
• Socket set
• A saw suitable for your project and the thickness of the timber
• Pencil
• Decking preservative
• Sandpaper or sander

1. Measure your deck frame and cut to size if necessary.
2. Make 2 pencil marks on each end of the frame’s 2 outer joists to mark where the coach screws will go. They need to align with the centre of the adjoining outer joist. Then, use a flat wood drill bit to drill recesses into each mark. Make them the same depth of the screws that your using’s head and wide enough for a ratchet or socket to tighten them.
3. Using a thinner drill bit, line up the outer joists and drill a pilot hole through the middle of the recess. These pilot holes act as a guide for the screws and stops them from splitting the wood.
4. Fit the coach screws with either a drill driver or socket and ratchet.
5. Repeat the process for the inner joists once you’ve assembled the outer frame.

There are several reasons why you may wish to plant a garden. To have a healthier environment, eat healthier, cook with fresh produce and lots more. Regardless of your purpose, one challenge faced by several home and property owners is exactly how to go about this and where to get started. If you’re having the same issues, then you’ve come to the right place. In this post, we’re going to take you through the process involved in planting a garden to ensure your project turns out a success. If you lack the confidence required to pull this off, we’d highly recommend you call in a professional who can guarantee the best results.

1. Start small. Being overly ambitious when planting a garden could be easiest way to a disastrous outcome. Give yourself a realistic goal and learn to plant healthy and productive plants by starting small.
2. Identify your site. To ensure a great garden, the plants need lots of sunlight. So, you can go for a space that gets about 6 to 8 hours of sunlight on a daily basis. Also, make sure that there’s a water source nearby to make it easy to give your plants water as required.
3. Choose you garden type. Decide how your garden will grow, be it in raised beds, in ground, in containers or a combination of styles. This will ensure that your garden is neat and orderly while also enhancing its curb appeal.
4. Make a list. Create a list of the plants you’d love to have in your garden.
5. Plan your planting. This involves spacing your plants as they’re going to grow bigger, deciding which plant goes where and identifying the best soil to grow them.
6. Get your plants.
7. Plant them.

When your driveway is suffering from depression, it becomes unsafe for driving (a danger zone) and ugly - no homeowner wants that! Unfortunately, most driveways won’t hold flat for long as they tend to develop cracks and potholes pretty quickly. Here, we are going to take you through how to fill asphalt driveways’ depression so as to ensure the sinkholes in your driveway poses no threat to you or your loved ones, while also beautifying your property. The approach to be used depends on the intensity of the depression. If its only a few cracks and holes, this can easily be repaired with some equipment. But if otherwise is the case, then calling a reliable professional will be your best bet. In this article, we’ll show you how to repair dips in your asphalt driveway relatively quickly.

✓ Pick a date with warm and sunny weather. This is because if you work in a cold weather, chances are the materials will freeze and hence, unusable. So find a day when the temperature will over 50 degrees Fahrenheit and below 80 degrees Celsius and when there would be no rain. We’ll advise a day between May to October.

✓ Prepare the area. Remove all loose stones, soil, dirt as well as vegetation from the holes. Once done, you can then proceed to washing the area with a pressure washer or sweep with a broom.

✓ Apply a thin mixture of asphalt to the area. Use a flat stirring stick to coat the low driveway area with a thin mixture of asphalt.

✓ Tamp the asphalt repair mix. Purchase the right kind of asphalt to repair the driveway. Fine aggregate asphalt mixture is more suited to filling small holes, whereas the coarse aggregate is more suited to filling larger holes. Apply layers ( about 2 inches each time) of the asphalt repair mix to the sunken area and use a shovel to give it a smooth finish. Once done, simply make the area smooth and protect it with a piece of plywood. Do not walk or drive on the area for a couple of days.

• Have a step tread width of 900mm – if you don’t want them that wide, they should be no less than 760mm
• Add a central step riser to stairs wider than 900mm to prevent them buckling
• Add a step depth (the vertical distance between each step) of between 150 and 180mm if building your own riser, so the steps are at a comfortable depth

• Step treads (the actual step themselves)
• Step risers
• Coach screws
• Deck screws
• Saw
• Drill

1. Make sure the ground where you want to put your steps is level and firm. If it’s not, consider laying concrete or paving slabs to provide a secure surface for your steps to sit so they don’t sink.
2. Grab some joist off-cuts and cut them to the same width as your step treads. Attach them to the step risers at the top and bottom using countersunk coach screws.
3. Place the steps against the sub-frame of the deck; if you’ve put slabs down for support, make sure the steps sit in the middle of them. The longest edge of the stair riser should be on the slabs, and the short edge against the deck. Drill pilot holes through the step and sub-frame joist, then screw the step to the sub-frame with more coach screws.
4. After drilling pilot holes, screw the treads into the risers at each end with deck screws.
5. If you don’t want gaps between each stair, you can add joist off-cuts or deck boards. Measure the height and depth of the gap, then screw the off-cut or board into the step riser with two screws at each end.

• Paving slabs – old or cheap ones are fine
• Timber for the frame and legs
• Type 1 MOT hardcore

1. Mark out the area as we explain in ‘How to lay decking’. Then, dig to 200mm below where you want to surface of the decking to be.
2. Add a 50mm layer of hardcore and make sure it’s compact.
3. Build the decking sub-frame as we describe in ‘How to build a deck frame’.
4. Lay out paving slabs along the edges and in the centre of the area. This will help to spread the weight of the decking.
5. Set the decking frame on the slabs, checking for high or low points and adding off-cuts of timber where needed. Don’t forget to sand and seal these off-cuts with decking preservative.
6. Add your joists and then the deck boards, leaving the recommended gaps of expansion of between 5-8mm.

1. If you’ve not got an overhang or it’s a fixed deck, fit starter clips along the outside edge of the frame and secure with screws provided with the composite decking. If you are working with an overhang, put the first board into position not exceeding 25mm. If you’re adding a fascia, put an off-cut of board under the overhang so you know it’ll be flush with the fascia.
2. Pre-drill all fixing points, measuring in 30mm from the edge of the board. Secure the board to the joist below with composite decking screws.
3. Slide a hidden fastener clip in so it sits within the groove of the deck board. It needs to be in the centre of the joist to keep the boards secure and ensure an expansion gap of 6mm. Tighten the clips until just tight, and repeat so there’s a clip at every joist.
4. Add the next board, ensuring that the fastener clips sit within the groove – make sure you don’t force it. Repeat step 3.
5. Continue steps 3 and 4 until you’re at the final board, which you should secure in the same way as you did the first.