Find a Landscaper you can trust in Cullompton.

Garden slabs are a joy to behold but only when done the right way. Well, the installation of paving slabs shouldn’t be exceed digging a little here and there, buying a small amount of mortar and pressing down the garden slab, right? Absolutely not! But we must admit how great it would have been if only it were that easy in real life. Let’s be honest, in reality, laying garden slabs does not only require you to prepare your sub-base painstakingly and mix your mortar using the appropriate materials, but you’d also have to work with accurate and precise paver placements to guarantee the patio’s longevity. Consequently, this happens to be a stressful and quite tricky challenge. If you lack the required confidence to pull this off, we’d recommend you hire the services of a seasoned professional who can guarantee the best results and also save you time and extra cash that may result from possible costly errors. In this guide, you’d gain more insight into the garden slabs laying process.

To get started, you’ll need sharp sand, cement, shovel, wheelbarrow, pointing trowel, rubber mallet, spirit level, jointing compound, hard-bristled brush and tarpaulin.

1. Mix a layer of mortar for each paver.
2. Apply the mixed mortar onto the sub base by using the trowel.
3. Slot the first flag in place and ensure not to stain the paver’s surface with the mixed mortar.
4. Using a rubber mallet, carefully tap the paver to the mortar bed. Once done, ensure the surface is even with a spirit level.
5. Take a measurement of the gap between the pavers
6. Repeat the above steps until all pavers have been perfectly laid
7. Leave the pavers to dry for about 1 to 2 days. You can protect it using a tarpaulin if concerned about rain.
8. Use the jointing compound to fill up the paver gaps to bind together the pavers. Ensure to wipe off any excess compound using the hard-bristled brush.

Moss, mushrooms and weeds are all problems that many homeowners face on their lawns. Luckily, with a bit of maintenance, there are ways you can get rid of these unwanted organisms and prevent them from coming back. Getting rid of moss A simple way to remove moss from your lawn is by scarification. This basically means that you vigorously rake your lawn, but only do this in the autumn when the grass is actively growing and it’s not too hot, cold or dry. However, you can also use specific weedkillers to control moss on your lawn, and most of these should be applied when the moss is actively growing. Apply in fine weather by hand or with a push-along spreader, making sure not to apply too much as you could kill off the grass too. Check the instructions, as some will require watering after 48 hours if it’s not rained. Then, get into a scarification routine to help prevent moss growth. Removing mushrooms from your lawn If you’ve got mushrooms in your lawn, it usually means that your lawn is damp and shaded, so it never dries out, and is organic waste-rich. There could be a drainage problem with your lawn that is encouraging mushroom growth, so it’s important to investigate why the mushrooms are growing to prevent them from returning once you’ve removed them. To get rid of mushrooms in your lawn, make sure you scarify your lawn and get rid of all the moss, thatch and dead grass that comes up. If you leave it, this is heaven for mushrooms to grow in. If your lawn is shaded, try to prune and thin surrounding trees to offer it more light. If you do all of these things, it will prevent mushrooms from growing in the future, and then it might be worth using a fungicide to get rid of the mushrooms that are there. But if you just do this step, it’s likely the mushrooms will just come back. How to get rid of weeds To get rid of weeds from your lawn, you can use selective weedkillers that will just kill the weeds and leave your grass alone. But if you’d rather not use weedkiller, you can get rid of weeds from your lawn manually. For large, deep-rooted weeds like dandelions or plantains, use a trowel to lever them out, ensuring that you get the whole plant including its roots. Then use compost to fill the hole it leaves behind, pushing it deeply into the hole. Sprinkle with fresh grass seed, cover with extra compost and water. Make sure you keep the area damp until the seed has germinated. To prevent moss, mushrooms or weeds from returning, the best things to do are:

• Scarify your lawn in the autumn, and lightly in the spring if necessary
• Seed your lawn in the autumn if you need to
• Try to keep trees trimmed and pruned as much as possible to reduce shade
• Use a pre-emergent weedkiller in the spring to catch them before they grow and handpick any that come through
• Mow your lawn regularly in the spring and summer, being careful not to remove more than a third of grass at a time, then before winter give it one last mow and a fertilisation treatment

The cheapest fence to install is, generally, a pressure-treated pine wooden fence at around £20 per linear foot. This includes the materials and labour costs. Wire fencing is technically cheaper at around £5 per foot, but it’s not a great material to use in homes as it looks unsightly and doesn’t provide any privacy.

Is there a hole in your asphalt driveway you feel you can repair yourself? If it’s something you know you can confidently do then this step by step guide is just for you. If otherwise, then we’d recommend you hire the services of a reliable professional who can guarantee the best results while also saving you some time and extra money that could result from possible errors. In this article, we’d go over the reparation process of an asphalt driveway with a hole in it.

✓ Get the necessary tools. You’re going to need a broom ( to clean the area), caulking gun ( to fill the hole), a hand tamp a plate compactor or a hammer ( to level the filled in hole) and a weeding glove (just in case there are weeds growing in the hole).

✓ Prepare the area. Do this by weeding the plants or weeds that might have grown inside the hole and identify your asphalt filler.

✓ Wet your soil, if necessary. It’s important to note that this is only necessary if your soil is dry to help the filler stick properly.

✓ Fill in deep holes. If the hole goes down about 3 to 4 inches or more, simply fill it with any material like rocks, clay etc.

✓ Apply the asphalt filler. Fill the hole with the asphalt filler to about half an inch higher than the surface of the driveway.

✓ Level the filler. For a large hole, make use of a plate compactor or a hand stamp, but a hammer will be sufficient for smaller holes.

✓ Cover the hole, if necessary. If your home isn’t level, covering your hole with a piece of plywood is advisable.

✓ Clean off the seal. After the asphalt looks done and in place, simply brush away the debris from the seal to finish off the project.

How To Repair Sunken Concrete Driveway

If you have concrete driveway that’s cracked, uneven and mostly especially sunken, you’d know how distasteful it can be just viewing it on your property. A sunken concrete driveway is most likely caused by rainwater erosion removing the soil under it or a big root under it which as rotted over time. Another possible cause of the sunken concrete is an improperly prepared base which implies that the soil beneath wasn’t fully compact when the concrete was poured on it. Later on the soil beneath will eventually settle and shift below the concrete driveway which weakens the integrity of the entire driveway, making it more vulnerable to cracks, unevenness and sunken.

Two ways in which you can fix this problem includes either demolishing the whole driveway, re-compact the soil underneath and fill with new concrete or repair the entire driveway using an easy process called slabjacking. In this article, we’re going to look at the slabjacking repair process as it’s significantly less expensive than the demolishing approach and will also cause minimal disruption to your lifestyle.

Also referred to as mudjacking or concrete lifting, slabjacking is simply a process used to float your existing concrete back to its original position. If you are not a competent DIYer or lack confidence to pull this off, we’d recommend reach out to a professional for help. If otherwise, then you can practice the slabjacking process given below.

✓ Drill holes through the slab.

✓ Pump grout mixture through the holes. This mixture will spread out beneath he driveway and raise it up.

✓ Lastly, fill the holes and level the concrete driveway surface.in such a way to hide the signs of the repair made.

This is a process that works to efficiently get your driveway back in a top condition relatively quickly.

For a lot of home and property owners in the UK, a common courtesy is being neighbourly and several people find it relatively easy to get along with the folks next door. However, for most individuals, where the major dispute arises most times is due to boundaries which can lead to impasse that may only be resolved through legal action. But since nobody wants that, when boundary issues become more than just passing a comment about the current condition of the fence, you may want to clue yourself up on what to do to get the desired action. If attempts have been made to talk to your neighbour to no avail, there are a couple of things you can consider to make “them next door repair their fence. In this post, we’re going to give you a good insight on these things to help you make informed decisions. Let’s take a look!

Firstly, it should be stated that if the fence poses an immediate danger then the usual legalities doesn’t apply. In this scenario, you may need to report to the local council who’ll take the necessary action on your behalf.

• Offer assistance. Since the cost of repairing a fence isn’t the cheapest thing to do, a lot of people might not be too eager to carry out this project and any friendly suggestion to do so may not be taken kindly. So if you feel that the this may be the issue, you can try offering some assistance to lessen the financial burden on your neighbour.
• Put up your own fence. If all attempts fail, you can consider erecting your own fence. However, this must be on your own property and as close to the boundary as possible.

If you’re thinking about a career in gardening or horticulture, regardless of the aspect there are relevant memberships, accreditations and qualifications available. First and foremost, gardening courses can range from as little as 6 months to a couple of years depending on the level of expertise that you require. Before you can be accepted as a member of a gardener’s association such as The Gardener’s Guild, you must prove to have a minimum of one horticultural qualification at Level two or above. It’s highly recommended that gardeners seek formal training in other to ensure a steady development - both personal and professional.

When it comes to gardening, qualifications are very important. They’ll give your customers the confidence in your commitment to your trade as well as your reliability. Having a qualification in gardening can also make you more efficient as you’ll be able to identify plant properly, know when they flower and need pruning etc, which helps you to effectively manage your time. The skills qualifications you’ll need include LANTRA and City and Guilds/NTPC qualifications which typically includes licenses for the use of horticultural equipment. For instance, if you plant to use a chainsaw, you’ll have to contact them to enquire about local courses. Licenses are a legal requirement in certain events and represents your seriousness when it comes to safety and environment issues.

RHS qualifications are also very popular amongst gardeners in the UK. The RHS courses can be completed at local colleges or through correspondence. Here, there are various modules that specialize in different horticulture topics and can also be combined to achieve higher level qualifications.