Find a Landscaper you can trust in Ivybridge.

How To Repair A Pothole In Gravel Driveways

When the integrity of your gravel driveway is impaired not only does it have a negative impact on the curb appeal of your property, but also makes your driveway a danger zone. If your driveway needs to be repaired, you’d simply have to grab the bull by the horn and get it done - the sooner, the better to avoid the problem getting worse and to have your beautiful gravel driveway back as soon as possible.

The major cause of potholes in driveways is usually water, when it gets trapped beneath the surface of the driveway. Therefore, you may also want to enhance the drainage in the area as part of your repair. The repair process is quite simple for confident do-it-yourselfers, but if otherwise, then calling in a reliable professional will save you some time and extra money that can result from possible errors. So how do you repair gravel driveway potholes?

✓ Prepare the area. This involves removing all forms of debris from the pothole. To achieve this, you can rake, shovel or brush the loose stones, soil and other debris from the pothole.

✓ Fill the pot hole. Make use of a coarse gravel to fill up the pothole to a depth of about 3 inches beneath the driveway’s level. Upon the filling, simply tamp down the coarse gravel using a commercial tamper or any available homemade option. Once done, the final 3 inches to the surface of the gravel driveway should then be filled up with gravel which perfectly matches the colour and texture of the remaining driveway.

✓ Compact the patch. To achieve this in an easy and fast way, simply run your car’s wheel up and down over the repaired spot gently a couple of times. This will be enough to compact the patch and seal the pothole.

If there’s a fence dividing yours and your neighbour’s properties that needs maintaining or replacing, you’ll want to know who owns it. Start by checking your deeds to see if there’s an existing boundary agreement. If there isn’t, have a chat with them to see if you can come to an arrangement yourselves.

It’s a good idea to talk to your neighbours before you start any work to avoid confusion along the way. But if the fence is definitely your responsibility and on your property, there’s no legal obligation to notify them. It’s also a myth that you need to erect a fence with the flush side without posts facing your neighbour’s property.

• Have a step tread width of 900mm – if you don’t want them that wide, they should be no less than 760mm
• Add a central step riser to stairs wider than 900mm to prevent them buckling
• Add a step depth (the vertical distance between each step) of between 150 and 180mm if building your own riser, so the steps are at a comfortable depth

• Step treads (the actual step themselves)
• Step risers
• Coach screws
• Deck screws
• Saw
• Drill

1. Make sure the ground where you want to put your steps is level and firm. If it’s not, consider laying concrete or paving slabs to provide a secure surface for your steps to sit so they don’t sink.
2. Grab some joist off-cuts and cut them to the same width as your step treads. Attach them to the step risers at the top and bottom using countersunk coach screws.
3. Place the steps against the sub-frame of the deck; if you’ve put slabs down for support, make sure the steps sit in the middle of them. The longest edge of the stair riser should be on the slabs, and the short edge against the deck. Drill pilot holes through the step and sub-frame joist, then screw the step to the sub-frame with more coach screws.
4. After drilling pilot holes, screw the treads into the risers at each end with deck screws.
5. If you don’t want gaps between each stair, you can add joist off-cuts or deck boards. Measure the height and depth of the gap, then screw the off-cut or board into the step riser with two screws at each end.

Most responsible contractors will dispose of the old fencing via an approved commercial waste site. Do check that the cost of taking rubbish away is included in the quotes you receive, otherwise you might find you get stung when it comes to paying for the work.

1. Remove fascias and trims Unscrew or prise off the screws and nails fixing the trims and fascias to your shed.
2. Take off doors and remove windows Unscrew hinges from doors and take them off. Remove all metalwork once the door is off. If you’ve got frames on your windows, unscrew these, and remove the panes. Be extra careful if your windows are made of glass.
3. Take off the roof Prise off the tacks from the roofing felt and take the felt off – you can’t reuse it, so you’ll need to throw it away. Unscrew the screws on the roof boards and slide them off the shed’s frame – you might need a friend to help you do this.
4. Take out the roof brace (optional) If your roof has a brace, unscrew the brackets that hold it to the side of the shed. Remember not to lean on anything once you’ve taken the brace off as the walls might be wobbly.
5. Unscrew the frame from the floor Remove all the screws that are holding the shed to the base, remembering not to lean on the walls.
6. Unscrew the frame corners Starting at the corner of the front gable, remove the screws where the panels meet. Once a panel is free, lift it carefully out of the way so you can carry on with the others.

Is there a hole in your asphalt driveway you feel you can repair yourself? If it’s something you know you can confidently do then this step by step guide is just for you. If otherwise, then we’d recommend you hire the services of a reliable professional who can guarantee the best results while also saving you some time and extra money that could result from possible errors. In this article, we’d go over the reparation process of an asphalt driveway with a hole in it.

✓ Get the necessary tools. You’re going to need a broom ( to clean the area), caulking gun ( to fill the hole), a hand tamp a plate compactor or a hammer ( to level the filled in hole) and a weeding glove (just in case there are weeds growing in the hole).

✓ Prepare the area. Do this by weeding the plants or weeds that might have grown inside the hole and identify your asphalt filler.

✓ Wet your soil, if necessary. It’s important to note that this is only necessary if your soil is dry to help the filler stick properly.

✓ Fill in deep holes. If the hole goes down about 3 to 4 inches or more, simply fill it with any material like rocks, clay etc.

✓ Apply the asphalt filler. Fill the hole with the asphalt filler to about half an inch higher than the surface of the driveway.

✓ Level the filler. For a large hole, make use of a plate compactor or a hand stamp, but a hammer will be sufficient for smaller holes.

✓ Cover the hole, if necessary. If your home isn’t level, covering your hole with a piece of plywood is advisable.

✓ Clean off the seal. After the asphalt looks done and in place, simply brush away the debris from the seal to finish off the project.