Find a Landscaper you can trust in Glogue.

As a home or property owner, you’re generally allowed to build next to your neighbour’s fence as long as it’s on your own side of the property. With that in mind, there are certain laws that regulate how close a fence can be built to buildings on the same lot or neighbouring lots. In addition, there are also local bylaws that provide limitations on the placements as well as height of fences so as to address safety hazards. In this post, we’re going to give you a good insight into how close you can build to your neighbour. Let’s take a look!

In general, if the fence is in your boundary then you’re allowed to build a 2-metre high brick or wooden fence or wall. However, this may differ depending on your location in the UK. As a result, you may want to reach out to your municipality’s building department in order to determine what these rules and limitations are in your area. In the events whereby there are no such restrictions but you’re still concerned, you can try informing your neighbour what your concerns are. However, if they’re not receptive there are some steps you can take to ensure your plans go as smoothly as possible. These steps include the following:

• Ensure to leave sufficient space for both the posts and footings
• Stagger your fence posts in order to make sure you’re not digging your neighbour’s
• Consider using concrete posts as they’re much stronger and will last a lot longer
• Use kickers or plinths for raised gardens and flower beds
• Make use of concrete plinths as they won’t rot over time like a wooden fence.

1. Unroll your two pieces of artificial grass, ensuring that the pile is running in the same direction. Fold over each piece by about 300m.
2. To get the perfect seam, cut at least 3 tufts back, ensuring that you don’t trim any grass blades.
3. Either remove the backing on your self-adhesive tape and unroll it down the centre of the join, or roll it out ensuring that the shiny side is down then fix at either end with adhesive.
4. Fold over the grass onto the tape and bring each piece together, ensuring there’s a 2-3mm gap at the seam.
5. Where the pile runs over the edge of the seam, fold over the artificial grass.
6. Apply a small amount of adhesive under the edge of the first section of grass with a mastic gun, then add some to the front edge to stick the second piece.
7. Bring the seam together, ensuring that you don’t get any grass blades stuck. Place a plank with some heavy objects on over the join to ensure that it dries securely.

1. Place a post in the corner of the frame you created with the pegs and string. Measure and mark out 100mm from each side.
2. Dig out this soil to a depth of 700mm (watch out for cables or pipes). You should have a 300 x 300mm hole. Repeat for the other 3 corners.
3. Using a brick bolster, split a concrete block in two. Put a section of the block in each hole.
4. Get a length of post longer than you need and place one in each hole. You can cut it down later.
5. Create props on each post to hold them in place until you’re ready to add a cement mix. Check that they’re level. When you’re happy that they are, secure them in place with a concrete mix, making sure you create a slope in the concrete so that rainwater runs away from each post. When the concrete is set, remove the props.
6. Create a string line around each corner post and find the centre point between each. Place a timber batten at each point, ensuring that they’re not spaced any more than 1500mm apart.

1. Working from the corner where the deck will be at its highest above ground level, measure and mark on the post where the highest part of the frame will be.
2. Measure from the far side of one post to the opposite and cut sections of joist to size. Line up a piece of joist with the mark you made and temporarily secure it. Factor in a 2mm fall for every metre of decking so rainwater can run off.
3. Secure the frame to the other corner post, ensuring it’s at the right level. Do this for every side of the outer frame.
4. Using 100mm coach screws with washers hanging on the end, secure each end of the four sections of frame.
5. Mark out where the centre of the support posts will be and secure all of these posts to the frame, except the centre post.
6. Add your central support joists. These should run in the same direction as the deck boards will run. You’ll need to measure from the inside of the frame on one side to the inside of the frame on the opposite side. Attach the joist in the same way as you did for the other posts. Repeat so the centre post is in between two sections of frame and secure the posts with concrete.
7. Trim down all the posts to the correct height using a saw.
8. Add your weed-control fabric and weigh down with gravel across the entire area.

1. Measure 400mm from the centre of the outer frame and mark a line. This will be where the first joist is positioned. Repeat at 400mm intervals down the length of the frame – if the last one will be more than 400mm, add another joist to create enough support.
2. Attach a joist hanger to each end of the joist.
3. Place the joist in position so the centre lines up with the 400mm spacer mark.
4. Secure using external grade screws once you’re happy that the joist is flush with the frame.

1. Start in one corner of the sub-frame and position the first board across the inner joists. You want the deck board in the opposite direction to the inner joists, ensuring that it’s flush with the frame. Position any end-to-end joins between the deck boards halfway across an inner joist so you can screw both boards into the joist for stability. Make sure you keep a gap of between 5-8mm to allow for expansion of the wood.
2. Begin to screw your deck boards to the joists. You’ll need to secure the deck board to every joist is covers along your deck frame. Use two screws for every joist. Mark where you’re going to add your screws, ensuring that they are at least 15mm from the end of the board and 20mm from the outside edges. Drill pilot holes for the screws, being careful to only drill through the deck board and not the joist. Then screw the decking screws into the holes.
3. Continue to screw in the deck boards, ensuring you leave the correct expansion gap. You can stagger the deck board joins across the deck for more strength.
4. Sand down any cut ends if you need to before applying decking preserver to protect the timber from rotting.

1. If you’ve not got an overhang or it’s a fixed deck, fit starter clips along the outside edge of the frame and secure with screws provided with the composite decking. If you are working with an overhang, put the first board into position not exceeding 25mm. If you’re adding a fascia, put an off-cut of board under the overhang so you know it’ll be flush with the fascia.
2. Pre-drill all fixing points, measuring in 30mm from the edge of the board. Secure the board to the joist below with composite decking screws.
3. Slide a hidden fastener clip in so it sits within the groove of the deck board. It needs to be in the centre of the joist to keep the boards secure and ensure an expansion gap of 6mm. Tighten the clips until just tight, and repeat so there’s a clip at every joist.
4. Add the next board, ensuring that the fastener clips sit within the groove – make sure you don’t force it. Repeat step 3.
5. Continue steps 3 and 4 until you’re at the final board, which you should secure in the same way as you did the first.

How To Plan A Landscape Garden

If you’ve decided to go for a landscape garden, this might imply putting in new gardens entirely or probably just coming up with a planting plan for the current year. However, because you want a beautiful landscape garden doesn’t mean you can just go out, get a couple of plants and decide to plant them anywhere that looks good to you once you get home.

For a much better landscape garden, doing some proper landscape garden planning can go a long way to help you get the results you desire. So how do you plan a landscape garden?

• Set Goals

The first step is to determine how you want the garden to feel and look, how it’s going to be used or what’s going to be used for as well as how you’ll work to boost the small ecosystem.

• Site Plan

Identify what you already have on the site like the plants, paths, gardens etc, and draw them out perhaps on a graph paper. Once done, you can make some photocopies and start playing with different ideas.

• Site Analysis

Carry out an in depth site analysis to identify the areas that’s sunny and shady areas as well as the ones in between. This way, you can figure out the best place to put the plants and other items.

• Functional Diagrams

This is stage at which you go through both the site plan as well as site analysis and start to identify the right spots to position the landscape garden’s items.

• Planting Plan

Here, you’ll decide which plants you’ll like to use on your landscape garden while also identifying what plant goes where. You’ll have to draw them at size close to what they’ll grow to become, so as to ensure there’s sufficient space for them once they grow big and tall.

1. How to build a shed base out of paving slabs
   • Mix sand and cement together to make mortar or use a pre-mixed one
   • Use a trowel to lay mortar for 1 slab at a time on the sub-base and lift a damp-sided slab onto the mortar, using a piece of timber and club hammer to tap the slab into position carefully. Continue to lay the first row of slabs
   • Make equally-sized spacers in all the joints in the slabs to ensure they’re the same size, checking it’s level as you go along
   • Next lay slabs along the two adjacent outer edges, filling in the central area row by row
   • Leave the mortar to set according to the instructions or for at least 48 hours before filling in the joints with mortar or paving grout
2. Building a shed base from concrete
   • Create a wooden frame around your shed base area (also called formwork) to stop the concrete from spreading
   • Mix pre-mixed concrete with water or use 1 part cement to 5 parts ballast
   • Wet the sub-base using a watering can with a rose on the end
   • Pour the concrete onto the framed base starting in one corner
   • Push the blade of a shovel up and down in the edges of the concrete to get rid of air bubbles
   • Use a rake to spread the concrete, leaving it around 18mm higher than the top of the frame. Work in sections of around 1-1.m²
   • Compact the concrete using a straight piece of timber that’s longer than the width of the base. Move the timber along the site, hitting it along at about half of its thickness at a time until the surface is evenly ridged
   • Remove excess concrete and level the surface by sliding the timber back and forwards from the edge that you started. Fill in any depressions and repeat until even
   • Run an edging trowel along the frame to round off exposed edges of the concrete and prevent chipping
   • Cover the concrete with a plastic sheet raised on wooden supports to allow slow drying. Weigh it down with bricks
   • Once the concrete is set, you can install your shed and remove the wooden frame with a crowbar

Laying a lawn is a task that’s best left to the professionals especially if you don’t know what you’re doing. However, if you can follow a simple logical process, you’ll save yourself a lot of headache – simply start from the edge and work inwards. If you’re looking to lay your lawn by yourself, then you’ve come to the right place! In this post, we’re going to consider the processes involved in lawn installation in order to ensure your project turns out a success. Let’s take a look!

Firstly, the tools you’re going to need to lay your lawn includes the following – sturdy boots, gardening gloves (should be thick), wheel barrow, garden fork or rotovator, landscaping rake, laying boards, knife or edge trimmer, hosepipe and broom.

1. Start from the outside edge. Install the initial strips horizontally overlapping the boundary a bit (trim the back once done). Press down carefully to make sure there’s a good contact with the soil (make sure not to squash the lawn).
2. Proceed to lay the adjacent pieces till the first row of the lawn along the entire edge is completed.
3. Continue with the next row. If there’s a need to stand on the laid turf, simply make use of a plank so as to avoid squashing or denting the turf. It’s important to ensure the successive rows are staggered to prevent the short edges from lining up.
4. Proceed by butting and pushing the edges to create a tight joint (make sure the turf is not stretched).
5. Use a wood saw or sharp serrated knife to trim any untidy edges. Remember to make use of a plank to ensure you do not walk directly on the turf.
6. Water the newly installed turf adequately to ensure the water penetrates the soil. However, do not turn it into a mud bath.