Find a Landscaper you can trust in Brentwood.

Laying artificial grass is a popular project – it’s a great way to create a smart, low-maintenance garden. There are plenty of professionals around who are experts at installing artificial grass, but it’s possible to DIY too if you’re feeling confident.

Lots of homeowners choose to replace their existing turf with artificial grass, so lay it on soil. To do this, start by clearing the area of any greenery or turf. Then remove any extra soil to a depth of about 40mm. You might want to leave the centre of your area slightly higher than the edges for a more natural look.

Next, you need to add a weed membrane and a sharp sand sub-base. It doesn’t really matter which one of these you do first, but you might find it easier to lay the weed membrane first and then use the sand to weigh it down, to a depth of about 35mm. Use a rake and plank to make the sand level, and compact it with a plank and heavy hammer. It doesn’t need to be completely flat – gentle slopes are fine. The weed membrane should overlap joints by 300mm.

After you’ve done this, you can lay your grass. Roll it out, trim it to size and fasten it in place. Make sure the ends of the grass rolls are staggered so they don’t end in a line. Lay the artificial grass with the pile (the strands) leaning towards the house so it looks nice and full when you’re looking out from the house. If you’ve decided to use edging boards, you can nail the grass into the tops of the boards. Or, if you haven’t, use ground pins to anchor it into the soil. Brush the grass and you’re done!

There is a variety of methods available to ensure that your paving drains properly, for example draining into a lawn or soakaway. Correct drainage of paving is a requirement for planning permission. See our guide on planning permission for paving for more information.

The best way to build a fence depends on what style it is, as different types have different components. However, fencing made up of posts and panels is pretty common. To put this up, you’ll need to start by measuring out and digging holes for your fence posts. Then you’ll need to fit the panels between them and use concrete to secure the posts in the ground.

Driveways usually sink because they haven’t been laid properly. They may not have been dug deep enough, or the installer might not have used the right materials. This will need to be corrected at the earliest opportunity, although in extreme cases, the driveway may need to be completly be relaid.

1. Mark out the area and dig the top layer of soil, trying to get the ground as flat as possible.
2. Build a timber frame to size.
3. Measure out 4 rows of 3 blocks to create good weight distribution and lay in place.
4. Underneath each block, dig around 50mm wider than the blocks and about 150mm deep. Fill the hole with pea gravel until it’s flat.
5. Place timber planks along the rows of blocks and see how level it is. Add or remove blocks where necessary. If it’s only a small difference, use shingle underneath the timber until it’s level.
6. Nail your timber shed base to the timber planks to create a sturdy base for your shed.

• Tongue and groove timber boards
• Boards for the ledges and braces, at least 20mm thick
• Nails
• Hammer
• Saws, including a circular saw
• Chisel
• Mallet

1. Cut your boards to size If you can’t buy boards at the right height and width for your door, cut the boards to length using a circular saw. Don’t forget to sand and treat any cut ends with timber preservative. Lay out the boards in the best arrangement for your shed door, with the inside of the door facing up.
2. Arrange the ledges and braces On most shed doors, you’ll probably need 3 boards across the back of the door to form the ledges. The ledges keep the door straight and keep the boards of the door together. The braces are the parts of the door that slope down to form a ‘Z’ shape between the ledges. Ensure that the braces are sloped up from the bottom and middle hinge to stop the door from sagging as the timber expands and contracts in the weather. Once you’re happy with the arrangement, mark the spots on the boards where they will meet and cut out of the housings using a chisel and mallet.
3. Put the door together Use clamps to pull the boards together and hold the ledges and braces in place. Nail from the front of the door through the boards and ledges to fix them. Secure the ledges and braces with screws; you may want to pre-drill and countersink holes to prevent the wood from splitting. Remember to treat them with preservative if you do.
4. Fix the shed door hinges Make sure you measure carefully before attaching the hinges, ensuring you know where the pin sits in relation to where the door opens.
5. Treat the door and add locks and handles Apply some wood oil, like linseed or teak oil, to help prevent water damage. Then add locks or handles to your shed to help keep it secure.
If you’d rather leave it to the professionals, there are plenty of specialists that will be able to make a shed door for you, or even put up an entire shed.

• What you need the shed for
• How much space you have
• How big you need the shed to be
• Which style of roof you want
• What material you would like
• How big your budget is

• Hand-crafted from Nordic White Spruce
• Felt roof reinforced with high-grade polyester
• Tongue and groove cladding makes it more weatherproof so ideal for items that must be kept dry

• High eaves for more head height and to store taller items
• Pent roof and fixed windows allow lots of light
• Ideal for putting up against a wall or fence
• Door can be hinged either side

• Ideal for small gardens or those with fewer tools to store
• Apex roof for water runoff
• Tongue and groove walls
• Tall floor-to-gable door

Chances are at some point you’d probably given a though about how steps would fit in perfectly in your garden, except of course, your yard and garden is flat. Adding steps and gardens makes it a lot easier to get around your yard while also enhancing its curb appeal. In order to avoid the cost of hiring a professional to get the task done, you might be tempted to make it a DIY task. However, if you lack the required skill and confidence to pull this off, we’d strongly recommend you call in a professional so as to avoid costly errors. In this post, we’re going to take you through the garden steps building process. Let’s take a look!

1. Measure the vertical height of the slope by marking it with two parallel lines. Once done, proceed by connecting a string line to the slope’s top and hold it in a horizontal way, take a measurement of the flight’s length and breadth. Divide the measurement by 200mm to get the number of steps that’ll be required. Then proceed to divide the number by the height to identify the depth of each step.
2. Working downwards from the flight’s top, dig the step shapes and also dig a shallow trench and install a concrete foundation.
3. Enable the foundation to harden by leaving it for about 48 hours, then install two courses of bricks on the concrete strip and use gravel to backfill.
4. With the help of a trowel, apply mortar to the top of the brickwork. Place the first slab on the mortar bed and press down. Then, make use of a spirit level to make sure that the steps are level.
5. On the back edge of the first tread, you should proceed to build the second rise, backfill and install the slab to form the second tread – just like the previous step. Repeat this process until you’ve gotten to the top of the flight.