Find a Landscaper you can trust in Cirencester.

1. If you’ve not got an overhang or it’s a fixed deck, fit starter clips along the outside edge of the frame and secure with screws provided with the composite decking. If you are working with an overhang, put the first board into position not exceeding 25mm. If you’re adding a fascia, put an off-cut of board under the overhang so you know it’ll be flush with the fascia.
2. Pre-drill all fixing points, measuring in 30mm from the edge of the board. Secure the board to the joist below with composite decking screws.
3. Slide a hidden fastener clip in so it sits within the groove of the deck board. It needs to be in the centre of the joist to keep the boards secure and ensure an expansion gap of 6mm. Tighten the clips until just tight, and repeat so there’s a clip at every joist.
4. Add the next board, ensuring that the fastener clips sit within the groove – make sure you don’t force it. Repeat step 3.
5. Continue steps 3 and 4 until you’re at the final board, which you should secure in the same way as you did the first.

1. Calculate the surface area for your decking Multiply the length (L) of your decking area by the width (W): L x W = Decking Surface Area (DSA) in m² 10 x 6 = 60m²
2. Work out the coverage of your deck boards Add your deck board width (DBW) to the expansion gap length (EGL), then add the deck board length (DBL) to the expansion gap width (EGW). Then multiply these numbers. (DBW + EGL) x (DBL + EGW) = Single Board Coverage (SBC) 0.144m + 0.005m = 0.149m 2.4m + 0.003m = 2.403m 0.149 x 2.403 = 0.358m²
3. Calculate the number of deck boards you need Multiply the SBC by 1.1 to allow for 10% wastage. Then, divide the DSA by the SBC. DSA / SCB x 1.1 = Total number of boards required 60m² / 0.358m² x 1.1 = 184.36 boards – so round up to 185 so you’re not left short.

Aeration, like scarification, is another vital step to keeping your lawn looking healthy and vibrant. It involves making small holes in the soil to allow air, water and nutrients to get into the grass roots, helping them to grow deeply, and produce a much stronger lawn. It also helps to relieve compaction from the soil, which stops nutrients and air from circulating. But how do you aerate your lawn?

Before you start to aerate your lawn, it’s a good idea to scarify it first to get rid of any moss, dead grass and thatch. This involves vigorously raking your lawn to get all the organic matter up, then transferring it to your compost heap or disposing of it. Light scarification is best in the spring but you can heavily scarify it in the autumn.

If you’ve got a small lawn, you can use a hand-held hollow tine aerator or even a normal garden fork. Dig deep into your lawn’s surface with the fork, or push the aerator into the ground which will pull plugs, or cores, of soil out of the ground to create air holes. You can let the cores dry and then go over them with a lawn mower or rake to spread them evenly across your lawn. This will recycle all the nutrients in those parts of the soil and stimulate bacterial activity to break down unwanted thatch. Don’t leave them, because they will make your lawn look bumpy over time.

If you’ve got a larger lawn, you might find it easier to see if you can hire a petrol aerator. But there are also rolling aerators that have spikes on a cylinder and you just push along, or even aerator sandals that you can wear and just go to town on your grass!

How To Draw A Garden Landscaping Plan

Are you thinking about constructing a new garden landscape? Do you have an existing one but forgot where you planted those tulip bulbs the previous autumn? Or perhaps you’re just trying to identify the exact spot where you cut back that clump of wilted foxglove, without mistakenly digging it up. For everything to be much easier when it comes to a garden landscape, it’s always a wise decision to draw a garden landscaping plan.

To get started, let’s take a look at the materials you’ll need to acquire. These includes a piece of white paper on which the existing elements on your garden will be plotted, a piece of tracing paper and tape to give options for planned additions, a pencil, an eraser as well as a measuring tape.

For more accuracy while drawing your plan, you’ll need to measure the garden’s distances, perimeter, the existing garden beds size as well as the trees’ and shrubs’ shape and size.

• Write down the measurements taken on the scrap paper.

• Assuming it’s a medium sized backyard garden that’s 18 feet wide, we allocated a scale of 3 feet to equal an inch.

• Using a piece of white paper (could be graph if you wish) and a pencil, carefully outline the perimeter of the space. Once done, you can then sketch in the existing plants as well as other special features on the space (features that are of a permanent nature like trees, fences and paths).

• Hold a piece of tracing paper and tape in on top. Then you can sketch out the plants you wish to add to fill in the spaces in the garden on the tracing paper.

1. Plan your shed base You must have a sturdy base for your shed, otherwise the frame won’t stand properly and could stop the door from opening. Decide whether you’re going to have:
   • A concrete base laid on hardcore
   • Concrete slabs on sharp sand
   • Treated wood beams on hardcore or shingle
   • An interlocking plastic system
   All bases should be laid on firm, level ground as far as possible.
2. Treat wood with preservative To help your shed last as long as possible, you should coat all the wooden parts with timber preservative before you put it together.
3. Put the shed floor together Some will need more assembly than others, but you need to make sure that the floor panel is attached to the joists; follow the manufacturer’s instructions for the correct spacing.
4. Put up the shed walls
   • Mark the centre point of each wall on its bottom edge, then do the same for the shed floor so you can line them up together.
   • Stand the gable end on the base and line it up. Check that it’s vertical with a spirit level – you might need someone to support the panel while you do this. Use a temporary holding batten to keep it in place.
   • Fix a side panel to the gable end panel with countersunk screws, then add the second side panel in the same way.
   Don’t attach the panels to the floor until you’ve fitted your shed roof.
5. Fit the roof
   • If the shed comes with a support bar, put this in position before you put the roof panels in.
   • Nail the roof panels in place, ensuring there’s a parallel and equal overlap at each end.
   • Roll out some roofing felt from front to back, leaving a 50mm overlap at each side. Secure it with clout-headed felt tacks at 100mm intervals.
   • Apply mastic sealant to the outside corners, then fix each corner trim with 30mm nails.
   • Add the fascias and finials, predrilling 2mm holes to avoid splitting the wood. Nail them through the felt into the shed using 40mm nails.
6. Add the shed windows
   • Slide each windowsill into the tongue and groove cut out, then put the window cover strip in position, fixing it to the vertical framing.
   • From inside the shed, put the glazing sheets into the window rebates, making sure the bottom edge of the glazing sheets sit on the outside of the sill.
   • Fix the window beading on the top and sides with 25mm nails.
7. Fix the walls to the floor Before you do anything, make sure you check that the centre marks on the walls line up with the marks on the shed floor. Then fix the wall panels to the floor with 50mm screws, aligning them with the joists.
And that’s it! But if you’re not confident in building a shed yourself, there are plenty of professionals available who will be happy to help.

1. How to build a shed base out of paving slabs
   • Mix sand and cement together to make mortar or use a pre-mixed one
   • Use a trowel to lay mortar for 1 slab at a time on the sub-base and lift a damp-sided slab onto the mortar, using a piece of timber and club hammer to tap the slab into position carefully. Continue to lay the first row of slabs
   • Make equally-sized spacers in all the joints in the slabs to ensure they’re the same size, checking it’s level as you go along
   • Next lay slabs along the two adjacent outer edges, filling in the central area row by row
   • Leave the mortar to set according to the instructions or for at least 48 hours before filling in the joints with mortar or paving grout
2. Building a shed base from concrete
   • Create a wooden frame around your shed base area (also called formwork) to stop the concrete from spreading
   • Mix pre-mixed concrete with water or use 1 part cement to 5 parts ballast
   • Wet the sub-base using a watering can with a rose on the end
   • Pour the concrete onto the framed base starting in one corner
   • Push the blade of a shovel up and down in the edges of the concrete to get rid of air bubbles
   • Use a rake to spread the concrete, leaving it around 18mm higher than the top of the frame. Work in sections of around 1-1.m²
   • Compact the concrete using a straight piece of timber that’s longer than the width of the base. Move the timber along the site, hitting it along at about half of its thickness at a time until the surface is evenly ridged
   • Remove excess concrete and level the surface by sliding the timber back and forwards from the edge that you started. Fill in any depressions and repeat until even
   • Run an edging trowel along the frame to round off exposed edges of the concrete and prevent chipping
   • Cover the concrete with a plastic sheet raised on wooden supports to allow slow drying. Weigh it down with bricks
   • Once the concrete is set, you can install your shed and remove the wooden frame with a crowbar

It’s a good idea to talk to your neighbours before you start any work to avoid confusion along the way. But if the fence is definitely your responsibility and on your property, there’s no legal obligation to notify them. It’s also a myth that you need to erect a fence with the flush side without posts facing your neighbour’s property.