Find a Landscaper you can trust in Llwyngwril.

Generally, a paved driveway is always subjected to regular usage and yours isn’t likely to be an exception, otherwise you won’t be here. Regular usage automatically necessitates regular maintenance of the driveway in order to extend its lifespan, make your property safer and add more value to it. This maintenance will involve a frequent inspection of the paved driveway so as to identify and repair divots, cracks as well as rutting. Paved driveways usually have a lifespan ranging between 15 to 20 years, but this can only be guaranteed when backed by regular maintenance activities. Failure to provide your paved driveway with a regular maintenance will lead to a rapid deterioration within just a couple of years after installation.

The issues commonly faced by paved driveways is usually different based on several factors such as the weather, your location, your property’s sub base as well as some other elements. The ability to identify the problems and solve or repair them on time is key to success while it’s also save you some time and money. In this article we’re going to look at how to go about do-it-yourself tasks that involves minor cracks. More intense damages are advised to be handled only by professionals.

✓ Prepare the area. Clear the debris, weed the plants or vegetation (if any).

✓ Use a strong spray from a garden hose to wash clean the cracks

✓ In the event whereby the crack is deep, simply fill it until it reach about a quarter inch of the surface with sand.

✓ Tamp down the sand to make it more compact.

✓ Apply a patching compound to the surface of the cracked paved driveway.

✓ Leave it for some time to cure.

✓ Once cured, you can then apply your sealant.

1. If you’ve not got an overhang or it’s a fixed deck, fit starter clips along the outside edge of the frame and secure with screws provided with the composite decking. If you are working with an overhang, put the first board into position not exceeding 25mm. If you’re adding a fascia, put an off-cut of board under the overhang so you know it’ll be flush with the fascia.
2. Pre-drill all fixing points, measuring in 30mm from the edge of the board. Secure the board to the joist below with composite decking screws.
3. Slide a hidden fastener clip in so it sits within the groove of the deck board. It needs to be in the centre of the joist to keep the boards secure and ensure an expansion gap of 6mm. Tighten the clips until just tight, and repeat so there’s a clip at every joist.
4. Add the next board, ensuring that the fastener clips sit within the groove – make sure you don’t force it. Repeat step 3.
5. Continue steps 3 and 4 until you’re at the final board, which you should secure in the same way as you did the first.

Does Landscaping A Garden Add Value?

When taking a good look at the image of new homes or perhaps you’re just thinking about getting one, one thing that several people will look out for is the garden. The thought of owning a perfect little oasis is all homeowners’ dream.

In a recent study conducted by Rightmove, it was discovered that to more than 60% of home buyers, an access to a garden was a priority. And according to the Royal Chartered Institute of Surveyors, this demand for garden is set to grow by 20% over the next 2 years.

Therefore, it’s obvious that having a beautiful landscaped garden is always a great asset to possess. But exactly how much value does a garden add to a property?

According to the studies carried out by Foxtons, it’s suggested that a garden can add as much as 20% to any property’s value, however, it should be expected that this value can vary based on a number of factors. In urban locations such as London, where there’s really not much outdoor space, possessing a garden can add an enormous amount to your property’s value.

However, if you happen to live in sub urban areas such as Wilmslow, where almost every home possesses a garden, what will influence the amount of value a garden will add to your property depends on it’s size as well as it’s unique features.

What’s more? Another important influence of a garden’s added value is the time of the season in which you’re selling your property. For more value, the best time to sell is always in the spring or summer when there are several gardens in bloom and multiple colours to please the eye. However, when it’s autumn and winter, the idea of staying outdoors for a quick get together or gardening is always very far, hence the value that’ll be added at this point may be low.

Is there a hole in your asphalt driveway you feel you can repair yourself? If it’s something you know you can confidently do then this step by step guide is just for you. If otherwise, then we’d recommend you hire the services of a reliable professional who can guarantee the best results while also saving you some time and extra money that could result from possible errors. In this article, we’d go over the reparation process of an asphalt driveway with a hole in it.

✓ Get the necessary tools. You’re going to need a broom ( to clean the area), caulking gun ( to fill the hole), a hand tamp a plate compactor or a hammer ( to level the filled in hole) and a weeding glove (just in case there are weeds growing in the hole).

✓ Prepare the area. Do this by weeding the plants or weeds that might have grown inside the hole and identify your asphalt filler.

✓ Wet your soil, if necessary. It’s important to note that this is only necessary if your soil is dry to help the filler stick properly.

✓ Fill in deep holes. If the hole goes down about 3 to 4 inches or more, simply fill it with any material like rocks, clay etc.

✓ Apply the asphalt filler. Fill the hole with the asphalt filler to about half an inch higher than the surface of the driveway.

✓ Level the filler. For a large hole, make use of a plate compactor or a hand stamp, but a hammer will be sufficient for smaller holes.

✓ Cover the hole, if necessary. If your home isn’t level, covering your hole with a piece of plywood is advisable.

✓ Clean off the seal. After the asphalt looks done and in place, simply brush away the debris from the seal to finish off the project.

1. Unroll your two pieces of artificial grass, ensuring that the pile is running in the same direction. Fold over each piece by about 300m.
2. To get the perfect seam, cut at least 3 tufts back, ensuring that you don’t trim any grass blades.
3. Either remove the backing on your self-adhesive tape and unroll it down the centre of the join, or roll it out ensuring that the shiny side is down then fix at either end with adhesive.
4. Fold over the grass onto the tape and bring each piece together, ensuring there’s a 2-3mm gap at the seam.
5. Where the pile runs over the edge of the seam, fold over the artificial grass.
6. Apply a small amount of adhesive under the edge of the first section of grass with a mastic gun, then add some to the front edge to stick the second piece.
7. Bring the seam together, ensuring that you don’t get any grass blades stuck. Place a plank with some heavy objects on over the join to ensure that it dries securely.

With summer comes a lot of lawn challenges - from sod webworms, chinch bugs, nutsedge to drought stress, diseases and lots more. A lot of people find it hard to tell what’s happening to their lawn and probably assume it to be as a result of the summer stress and will definitely turn green again once the fall rolls in. This may be right in certain situations, but if you have fungi eating deep into your lawn, the green may not return. So, how exactly do you figure out if your lawn has diseases or pests? In this post, we’re going to provide you with a good insight into this to help you take the necessary treatment steps as soon as possible.

• Fungal structures. Fungi structures are not usually the easiest to spot as they vary in shape, colour and appearance. Fortunately, most fungi that appears on lawns will possess some type of structure which can be spotted when moisture is present. Once the night time dew sets in, you’ll be able to identify these strange growths in your lawn.
• Matted or Collapsed Areas. There is some sort of diseases that will make grass plant to wilt in little time. This, combined with fungi structures will make the grass look to have been matted in some areas.
• Discoloured or oily areas. Some areas are likely to show symptoms more than the others. While the unaffected turf may remain in its normal state, areas that are nearby may vary in colour due to the damage to the leaf tissue.
• Lesions or spots on leaves. Do you notice a certain damage pattern on the leaf blades of the grass plants? If yes, then your lawn is probably infected with a disease. Some of these spots may vary in size and colour.

Not if they are under 1 metre high if next to a road or 2 metres high elsewhere. It’s always recommended to check with your neighbours and the local authority if you are unsure. Other restrictions may apply, for example if a fence might impact driver visibility on nearby roads.

Laying a lawn is a task that’s best left to the professionals especially if you don’t know what you’re doing. However, if you can follow a simple logical process, you’ll save yourself a lot of headache – simply start from the edge and work inwards. If you’re looking to lay your lawn by yourself, then you’ve come to the right place! In this post, we’re going to consider the processes involved in lawn installation in order to ensure your project turns out a success. Let’s take a look!

Firstly, the tools you’re going to need to lay your lawn includes the following – sturdy boots, gardening gloves (should be thick), wheel barrow, garden fork or rotovator, landscaping rake, laying boards, knife or edge trimmer, hosepipe and broom.

1. Start from the outside edge. Install the initial strips horizontally overlapping the boundary a bit (trim the back once done). Press down carefully to make sure there’s a good contact with the soil (make sure not to squash the lawn).
2. Proceed to lay the adjacent pieces till the first row of the lawn along the entire edge is completed.
3. Continue with the next row. If there’s a need to stand on the laid turf, simply make use of a plank so as to avoid squashing or denting the turf. It’s important to ensure the successive rows are staggered to prevent the short edges from lining up.
4. Proceed by butting and pushing the edges to create a tight joint (make sure the turf is not stretched).
5. Use a wood saw or sharp serrated knife to trim any untidy edges. Remember to make use of a plank to ensure you do not walk directly on the turf.
6. Water the newly installed turf adequately to ensure the water penetrates the soil. However, do not turn it into a mud bath.