Find a Landscaper you can trust in Borehamwood.

Laying a lawn is a task that’s best left to the professionals especially if you don’t know what you’re doing. However, if you can follow a simple logical process, you’ll save yourself a lot of headache – simply start from the edge and work inwards. If you’re looking to lay your lawn by yourself, then you’ve come to the right place! In this post, we’re going to consider the processes involved in lawn installation in order to ensure your project turns out a success. Let’s take a look!

Firstly, the tools you’re going to need to lay your lawn includes the following – sturdy boots, gardening gloves (should be thick), wheel barrow, garden fork or rotovator, landscaping rake, laying boards, knife or edge trimmer, hosepipe and broom.

1. Start from the outside edge. Install the initial strips horizontally overlapping the boundary a bit (trim the back once done). Press down carefully to make sure there’s a good contact with the soil (make sure not to squash the lawn).
2. Proceed to lay the adjacent pieces till the first row of the lawn along the entire edge is completed.
3. Continue with the next row. If there’s a need to stand on the laid turf, simply make use of a plank so as to avoid squashing or denting the turf. It’s important to ensure the successive rows are staggered to prevent the short edges from lining up.
4. Proceed by butting and pushing the edges to create a tight joint (make sure the turf is not stretched).
5. Use a wood saw or sharp serrated knife to trim any untidy edges. Remember to make use of a plank to ensure you do not walk directly on the turf.
6. Water the newly installed turf adequately to ensure the water penetrates the soil. However, do not turn it into a mud bath.

1. How to build a shed base out of paving slabs
   • Mix sand and cement together to make mortar or use a pre-mixed one
   • Use a trowel to lay mortar for 1 slab at a time on the sub-base and lift a damp-sided slab onto the mortar, using a piece of timber and club hammer to tap the slab into position carefully. Continue to lay the first row of slabs
   • Make equally-sized spacers in all the joints in the slabs to ensure they’re the same size, checking it’s level as you go along
   • Next lay slabs along the two adjacent outer edges, filling in the central area row by row
   • Leave the mortar to set according to the instructions or for at least 48 hours before filling in the joints with mortar or paving grout
2. Building a shed base from concrete
   • Create a wooden frame around your shed base area (also called formwork) to stop the concrete from spreading
   • Mix pre-mixed concrete with water or use 1 part cement to 5 parts ballast
   • Wet the sub-base using a watering can with a rose on the end
   • Pour the concrete onto the framed base starting in one corner
   • Push the blade of a shovel up and down in the edges of the concrete to get rid of air bubbles
   • Use a rake to spread the concrete, leaving it around 18mm higher than the top of the frame. Work in sections of around 1-1.m²
   • Compact the concrete using a straight piece of timber that’s longer than the width of the base. Move the timber along the site, hitting it along at about half of its thickness at a time until the surface is evenly ridged
   • Remove excess concrete and level the surface by sliding the timber back and forwards from the edge that you started. Fill in any depressions and repeat until even
   • Run an edging trowel along the frame to round off exposed edges of the concrete and prevent chipping
   • Cover the concrete with a plastic sheet raised on wooden supports to allow slow drying. Weigh it down with bricks
   • Once the concrete is set, you can install your shed and remove the wooden frame with a crowbar

Everyone wants a good-looking lawn! If you’re wondering the best time to scarify your lawn, then you’ve come to the right place! In this post, we’re going to consider this in order to help you make the best-informed decision possible. Let’s take a look!

The short and simple answer to this question is when your grass is actively growing. This is the best time to scarify a lawn as it enables it to recover faster once it has been scarified. What’s more? The conditions also have to be appropriate as extreme weather condition, be it too cold, too warm, too dry or too hot, will hinder the quick and proper recovery of your lawn. It’s also important to take note that scarifying of a lawn is going to leave the soil exposed which makes way for weed and other unwanted plants to grow.

During the year, there are two different times which tends to provide the most ideal conditions to scarify a lawn. The first of these periods is late March or April when the spring is in the air and your grass receives all the warmth and moisture it needs to thrive. It’s also advisable not to wait till too late in the spring as right after this period comes the heat and dryness of summer. Furthermore, the lawn shouldn’t be scarified too heavily during the spring as summer usually comes with weed seeds which means your grass won’t recover fast enough and weeds will quickly make way for themselves.

If you wish to scarify your lawn heavily, then the perfect time to do this would be in September or October – during autumn. During this period, the summer weed seeds would be gone and the grass will grow properly.

Driveways usually sink because they haven’t been laid properly. They may not have been dug deep enough, or the installer might not have used the right materials. This will need to be corrected at the earliest opportunity, although in extreme cases, the driveway may need to be completly be relaid.

1. Unroll your two pieces of artificial grass, ensuring that the pile is running in the same direction. Fold over each piece by about 300m.
2. To get the perfect seam, cut at least 3 tufts back, ensuring that you don’t trim any grass blades.
3. Either remove the backing on your self-adhesive tape and unroll it down the centre of the join, or roll it out ensuring that the shiny side is down then fix at either end with adhesive.
4. Fold over the grass onto the tape and bring each piece together, ensuring there’s a 2-3mm gap at the seam.
5. Where the pile runs over the edge of the seam, fold over the artificial grass.
6. Apply a small amount of adhesive under the edge of the first section of grass with a mastic gun, then add some to the front edge to stick the second piece.
7. Bring the seam together, ensuring that you don’t get any grass blades stuck. Place a plank with some heavy objects on over the join to ensure that it dries securely.

• Paving slabs – old or cheap ones are fine
• Timber for the frame and legs
• Type 1 MOT hardcore

1. Mark out the area as we explain in ‘How to lay decking’. Then, dig to 200mm below where you want to surface of the decking to be.
2. Add a 50mm layer of hardcore and make sure it’s compact.
3. Build the decking sub-frame as we describe in ‘How to build a deck frame’.
4. Lay out paving slabs along the edges and in the centre of the area. This will help to spread the weight of the decking.
5. Set the decking frame on the slabs, checking for high or low points and adding off-cuts of timber where needed. Don’t forget to sand and seal these off-cuts with decking preservative.
6. Add your joists and then the deck boards, leaving the recommended gaps of expansion of between 5-8mm.

• Blade material Artificial grass is made up of lots of individual blades, just like real grass. The blades are made of plastic and are sewn to a backing material. To help keep your artificial grass looking great for longer, a blend of blades made from nylon and polyethylene are best. Nylon is extremely resilient, but isn’t very comfy to walk on, so adding the polyethylene which is still very strong helps to keep it feeling nice underfoot.
• Backing material The backing material holds all the artificial grass blades together. It’s made of two layers: a membrane that the grass is attached to, and a section that’s usually made of latex or polyurethane and bonds everything together. When you’re choosing your artificial grass, ask for samples – try to pull away the backing material. If it comes apart easily, steer clear of that type of grass.
• The artificial grass’ use The lifespan of your artificial grass will depend on how much traffic it gets. It’s best to invest in strong nylon or nylon-blend turfs where it’s going to get walked on regularly, such as on a pathway to a door. Of course, if the artificial grass is more ornamental, a lower-quality product will last a long time.
• Good installation One of the main things that will help your artificial grass last a long time is effective installation. If artificial grass is laid badly, it might suffer from poor drainage and weeds which will reduce its lifespan. It’s always best to get your artificial grass installed by a professional since they’re trained in fitting it to a high standard.