Find a Landscaper you can trust in Forsinard.

1. Start in one corner of the sub-frame and position the first board across the inner joists. You want the deck board in the opposite direction to the inner joists, ensuring that it’s flush with the frame. Position any end-to-end joins between the deck boards halfway across an inner joist so you can screw both boards into the joist for stability. Make sure you keep a gap of between 5-8mm to allow for expansion of the wood.
2. Begin to screw your deck boards to the joists. You’ll need to secure the deck board to every joist is covers along your deck frame. Use two screws for every joist. Mark where you’re going to add your screws, ensuring that they are at least 15mm from the end of the board and 20mm from the outside edges. Drill pilot holes for the screws, being careful to only drill through the deck board and not the joist. Then screw the decking screws into the holes.
3. Continue to screw in the deck boards, ensuring you leave the correct expansion gap. You can stagger the deck board joins across the deck for more strength.
4. Sand down any cut ends if you need to before applying decking preserver to protect the timber from rotting.

Most responsible contractors will dispose of the old fencing via an approved commercial waste site. Do check that the cost of taking rubbish away is included in the quotes you receive, otherwise you might find you get stung when it comes to paying for the work.

Properly erected fences shouldn’t require a great deal of maintenance. Any rotting boards can usually be replaced without replacing the whole panel. Timber fencing should be stained every 2-3 years. General maintenance is something you can carry out yourself, however, larger works may need a qualified professional to come in.

Yes, it is possible to insulate a shed. You might want to do this if you’re planning on working in it during the winter. A professional will be able to help you find an insulated shed or advise you on how to insulate a shed that you already have. Always seek professional advise first before attempting to do this yourself!

Laying artificial grass on concrete needs a slightly different approach to if you’re installing it over soil. The good news is that it’s much less labour intensive, as you don’t need to do any digging or levelling.

Ideally, your concrete base should be in good condition, and have an adequate fall on it to provide efficient drainage. If it doesn’t, you might have to do some repair work or drill some drainage holes first.

When you’re ready to start, begin by cleaning your concrete base. Use a jet wash or a hose and brush to dislodge and disperse any dirt or plant growth. Once it’s clean, leave it to dry completely.

Then, you need to fit an underlay - usually it’s made of foam. This will provide padding to make your artificial grass softer and more comfortable to walk on. It will also help to level out any slopes on uneven parts on the concrete. Make sure it’s a good-quality underlay that’s permeable – if it’s not, you could end up with damp artificial grass and nasty smells as it will hold moisture. Roll out the underlay and cut it to shape, taping any separate sections together.

Next, use an adhesive to secure the underlay to your concrete. Make sure you leave gaps in the adhesive to allow water to drain off easily. Leave the glue to dry, then you can start laying your grass.

Roll out your grass like you did with your underlay, cutting it to shape and joining any separate sections together with artificial grass tape. Then glue the grass to the underlay. Leave it dry, give the grass a brush, and it’ll be ready to use!

A patio is an outdoor space which can be used for a variety of stuffs which includes fun time with family and friends, reading time or just relaxing as the fresh breeze blows. With all these benefits and more, it’s becomes more obvious that there’s a need to keep your patio in a tip top condition at all times. If otherwise, you may not be able to enjoy your patio to your satisfaction and probably, for as long as you would want. You simply have to provide it with a regular maintenance which involves inspecting and identifying the damages that needs to be repaired before it gets out of hand. Fortunately, the minor repairs can be done by yourself if you’re confident enough. However, for bigger damages it’s advisable to call in a professional for help. In this article, we’ll take you through the patio reparation process.

✓ Prepare the area. This involves removing the problem piece gently and carefully. If there’s a piece you think can still be useful, store it in the re-use pile or you can start a new one. Once you’re done removing the pieces, the next thing to do would be to start removing anything that’s unwanted from the damaged area like debris, unwanted soil etc, and start sand fitting with some fresh sand. This should be levelled out to ensure there’s no bumps.

✓ With the sand down, you can start by putting the pieces back in together. This should be done gently to avoid any further damage. Do this until your patio

✓

How To Repair Sunken Concrete Driveway

If you have concrete driveway that’s cracked, uneven and mostly especially sunken, you’d know how distasteful it can be just viewing it on your property. A sunken concrete driveway is most likely caused by rainwater erosion removing the soil under it or a big root under it which as rotted over time. Another possible cause of the sunken concrete is an improperly prepared base which implies that the soil beneath wasn’t fully compact when the concrete was poured on it. Later on the soil beneath will eventually settle and shift below the concrete driveway which weakens the integrity of the entire driveway, making it more vulnerable to cracks, unevenness and sunken.

Two ways in which you can fix this problem includes either demolishing the whole driveway, re-compact the soil underneath and fill with new concrete or repair the entire driveway using an easy process called slabjacking. In this article, we’re going to look at the slabjacking repair process as it’s significantly less expensive than the demolishing approach and will also cause minimal disruption to your lifestyle.

Also referred to as mudjacking or concrete lifting, slabjacking is simply a process used to float your existing concrete back to its original position. If you are not a competent DIYer or lack confidence to pull this off, we’d recommend reach out to a professional for help. If otherwise, then you can practice the slabjacking process given below.

✓ Drill holes through the slab.

✓ Pump grout mixture through the holes. This mixture will spread out beneath he driveway and raise it up.

✓ Lastly, fill the holes and level the concrete driveway surface.in such a way to hide the signs of the repair made.

This is a process that works to efficiently get your driveway back in a top condition relatively quickly.

1. Mark out the area and dig the top layer of soil, trying to get the ground as flat as possible.
2. Build a timber frame to size.
3. Measure out 4 rows of 3 blocks to create good weight distribution and lay in place.
4. Underneath each block, dig around 50mm wider than the blocks and about 150mm deep. Fill the hole with pea gravel until it’s flat.
5. Place timber planks along the rows of blocks and see how level it is. Add or remove blocks where necessary. If it’s only a small difference, use shingle underneath the timber until it’s level.
6. Nail your timber shed base to the timber planks to create a sturdy base for your shed.