Find a Landscaper you can trust in Lincoln.

This will depend on the size of the garden and the amount of plants within it. For small gardens, fortnightly or monthly visits by a professional gardener will generally be sufficient. For larger gardens or gardens with a lot of plants, weekly visits are best. Some larger projects such as hedge cutting or tree felling may need additional one off visits.

• Paving slabs – old or cheap ones are fine
• Timber for the frame and legs
• Type 1 MOT hardcore

1. Mark out the area as we explain in ‘How to lay decking’. Then, dig to 200mm below where you want to surface of the decking to be.
2. Add a 50mm layer of hardcore and make sure it’s compact.
3. Build the decking sub-frame as we describe in ‘How to build a deck frame’.
4. Lay out paving slabs along the edges and in the centre of the area. This will help to spread the weight of the decking.
5. Set the decking frame on the slabs, checking for high or low points and adding off-cuts of timber where needed. Don’t forget to sand and seal these off-cuts with decking preservative.
6. Add your joists and then the deck boards, leaving the recommended gaps of expansion of between 5-8mm.

1. Remove fascias and trims Unscrew or prise off the screws and nails fixing the trims and fascias to your shed.
2. Take off doors and remove windows Unscrew hinges from doors and take them off. Remove all metalwork once the door is off. If you’ve got frames on your windows, unscrew these, and remove the panes. Be extra careful if your windows are made of glass.
3. Take off the roof Prise off the tacks from the roofing felt and take the felt off – you can’t reuse it, so you’ll need to throw it away. Unscrew the screws on the roof boards and slide them off the shed’s frame – you might need a friend to help you do this.
4. Take out the roof brace (optional) If your roof has a brace, unscrew the brackets that hold it to the side of the shed. Remember not to lean on anything once you’ve taken the brace off as the walls might be wobbly.
5. Unscrew the frame from the floor Remove all the screws that are holding the shed to the base, remembering not to lean on the walls.
6. Unscrew the frame corners Starting at the corner of the front gable, remove the screws where the panels meet. Once a panel is free, lift it carefully out of the way so you can carry on with the others.

How To Repair Sunken Concrete Driveway

If you have concrete driveway that’s cracked, uneven and mostly especially sunken, you’d know how distasteful it can be just viewing it on your property. A sunken concrete driveway is most likely caused by rainwater erosion removing the soil under it or a big root under it which as rotted over time. Another possible cause of the sunken concrete is an improperly prepared base which implies that the soil beneath wasn’t fully compact when the concrete was poured on it. Later on the soil beneath will eventually settle and shift below the concrete driveway which weakens the integrity of the entire driveway, making it more vulnerable to cracks, unevenness and sunken.

Two ways in which you can fix this problem includes either demolishing the whole driveway, re-compact the soil underneath and fill with new concrete or repair the entire driveway using an easy process called slabjacking. In this article, we’re going to look at the slabjacking repair process as it’s significantly less expensive than the demolishing approach and will also cause minimal disruption to your lifestyle.

Also referred to as mudjacking or concrete lifting, slabjacking is simply a process used to float your existing concrete back to its original position. If you are not a competent DIYer or lack confidence to pull this off, we’d recommend reach out to a professional for help. If otherwise, then you can practice the slabjacking process given below.

✓ Drill holes through the slab.

✓ Pump grout mixture through the holes. This mixture will spread out beneath he driveway and raise it up.

✓ Lastly, fill the holes and level the concrete driveway surface.in such a way to hide the signs of the repair made.

This is a process that works to efficiently get your driveway back in a top condition relatively quickly.

Laying a lawn is a task that’s best left to the professionals especially if you don’t know what you’re doing. However, if you can follow a simple logical process, you’ll save yourself a lot of headache – simply start from the edge and work inwards. If you’re looking to lay your lawn by yourself, then you’ve come to the right place! In this post, we’re going to consider the processes involved in lawn installation in order to ensure your project turns out a success. Let’s take a look!

Firstly, the tools you’re going to need to lay your lawn includes the following – sturdy boots, gardening gloves (should be thick), wheel barrow, garden fork or rotovator, landscaping rake, laying boards, knife or edge trimmer, hosepipe and broom.

1. Start from the outside edge. Install the initial strips horizontally overlapping the boundary a bit (trim the back once done). Press down carefully to make sure there’s a good contact with the soil (make sure not to squash the lawn).
2. Proceed to lay the adjacent pieces till the first row of the lawn along the entire edge is completed.
3. Continue with the next row. If there’s a need to stand on the laid turf, simply make use of a plank so as to avoid squashing or denting the turf. It’s important to ensure the successive rows are staggered to prevent the short edges from lining up.
4. Proceed by butting and pushing the edges to create a tight joint (make sure the turf is not stretched).
5. Use a wood saw or sharp serrated knife to trim any untidy edges. Remember to make use of a plank to ensure you do not walk directly on the turf.
6. Water the newly installed turf adequately to ensure the water penetrates the soil. However, do not turn it into a mud bath.

Uneven lawn? Well, for an outdoor space which looks great and serves its purpose throughout the year, there’s a need to learn how to level your garden. While its best left for a professional to handle, there are also some simple steps you can follow to ensure your DIY task turns out a success whether you’re preparing to lay a patio or deck, landscaping the whole space or tackling a lumpy lawn. A level ground comes with a bunch of benefits which includes maximizing the functions of your yard, helping with drainage while also enhancing your property’s curb appeal. Good news is, you can level your sloping lawn by hand. Want to know how? In this post, we’re going to take you through the processes involved in levelling an uneven lawn. Let’s take a look!

You can simply level your lawn using your hand if you aim to make your lawn a more even surface or to install a patio or deck. If your goal is only to make the lawn more even, you should have it in mind that, even though lumps and bumps aren’t always pleasing for most people, it can actually create a good drainage for your home.

Top dressing is the solution for depressions that are about 2cm to 3cm deep. To resolve this, simply get a top dressing mixture or make yours using two parts of sand and topsoil and a single part of compost. Use this to fill out the depression evenly and make compact using a rake or your feet, then water. Leave this for two days before applying grass seed alongside a thin layer of topsoil, then water as needed.

If you have a deeper depression, simply dig out to around 4cm to 5cm and remove any lumps of soil or stones. Once done, proceed to top dressing as explained above and grass seed to fill out the bald spot.

If you’re thinking about a career in gardening or horticulture, regardless of the aspect there are relevant memberships, accreditations and qualifications available. First and foremost, gardening courses can range from as little as 6 months to a couple of years depending on the level of expertise that you require. Before you can be accepted as a member of a gardener’s association such as The Gardener’s Guild, you must prove to have a minimum of one horticultural qualification at Level two or above. It’s highly recommended that gardeners seek formal training in other to ensure a steady development - both personal and professional.

When it comes to gardening, qualifications are very important. They’ll give your customers the confidence in your commitment to your trade as well as your reliability. Having a qualification in gardening can also make you more efficient as you’ll be able to identify plant properly, know when they flower and need pruning etc, which helps you to effectively manage your time. The skills qualifications you’ll need include LANTRA and City and Guilds/NTPC qualifications which typically includes licenses for the use of horticultural equipment. For instance, if you plant to use a chainsaw, you’ll have to contact them to enquire about local courses. Licenses are a legal requirement in certain events and represents your seriousness when it comes to safety and environment issues.

RHS qualifications are also very popular amongst gardeners in the UK. The RHS courses can be completed at local colleges or through correspondence. Here, there are various modules that specialize in different horticulture topics and can also be combined to achieve higher level qualifications.