Find a Landscaper you can trust in Stamford.

Scarification is the name given to the process where you remove excess thatch and moss from your lawn to encourage it to grow and look healthy. Although it sounds difficult, it’s actually pretty easy – simply grab a sturdy rake and apply moderate pressure to rake out moss, thatch and dead grass. Then collect it up and add to your compost heap if you have one. You can also use a petrol or electric rake, but you just want to tease out the moss and thatch. Don’t be tempted to go deep into the grass, as this could damage your lawn. So when should you scarify your lawn? The experts say that the best time is in the autumn, when the grass is actively growing and it’s not too hot, cold or dry. Most of summer’s weed seeds will have gone, so you won’t encourage weeds to grow in the raked-up soil. This soil also makes an ideal seed bed for over seeding with new grass seed, so that’s why you don’t want to get weeds in there as well. However, you may also carry out light scarification in the spring – usually around April. Make sure you don’t go too far though – as you will end up with a rather disfigured lawn if you scarify too heavily and the dryness of summer stops the lawn from recovering. It’s also best to scarify your lawn in the spring if the following apply:

• If you couldn’t do it the previous autumn – if you keep putting it off, you might end up with extreme moss and weed growth
• If your lawn is shaded – these areas will thin over winter and start to thicken from spring onwards, so if you scarify in the autumn you’ll make your lawn even thinner.
• If your lawn is under trees – pair the shade from the trees with the fall of leaves in the autumn and your grass won’t be healthy, but in the spring the trees are bare, allowing lots of light onto your lawn to help it grow.

First and foremost, to save your time and money when it comes to lawn renovation, there’s a huge need to figure out why the lawn isn’t doing well in the first place. A lot of times, when changes are made to the basic lawn care practices, cultural practices or site conditions, any need for a renovation would be thrown out the window as the lawn would be given a new life with good health and vigour. However, if you feel renovation is the best option for your lawn, then you’ve come to the right place! In this post, we’re going to consider the best time to start a lawn renovation to help put you on the right path. Let’s take a look!

There are two times during the year that are most suitable for lawn renovation. Firstly, the best time for renovation of a lawn is usually from mid-August to mid-September. Secondly, another great time to achieve this goal is normally during early spring as the lawn is starting to turn green and grow.

So, when do you consider lawn renovation?

• When the quality of the lawn is simply poor and unacceptable.
• During the introduction of lower maintenance turf varieties into an existing lawn.
• When 30% to 50% of the lawn is dead or is experiencing sparse growth which may be due to several factors like drought and heat, low soil fertility, insect damage, moderate soil compaction and more.
• When the lawn is soft and spongy will walking across. Plus, if it also responds terribly to the application of fertilizer and water.
• When grassy weeds or broad-leaved weeds covers about 30 to 40 percent of the lawn area with insufficient turf cover to fill in the bare areas once the weed removal is done.

Laying a lawn is a task that’s best left to the professionals especially if you don’t know what you’re doing. However, if you can follow a simple logical process, you’ll save yourself a lot of headache – simply start from the edge and work inwards. If you’re looking to lay your lawn by yourself, then you’ve come to the right place! In this post, we’re going to consider the processes involved in lawn installation in order to ensure your project turns out a success. Let’s take a look!

Firstly, the tools you’re going to need to lay your lawn includes the following – sturdy boots, gardening gloves (should be thick), wheel barrow, garden fork or rotovator, landscaping rake, laying boards, knife or edge trimmer, hosepipe and broom.

1. Start from the outside edge. Install the initial strips horizontally overlapping the boundary a bit (trim the back once done). Press down carefully to make sure there’s a good contact with the soil (make sure not to squash the lawn).
2. Proceed to lay the adjacent pieces till the first row of the lawn along the entire edge is completed.
3. Continue with the next row. If there’s a need to stand on the laid turf, simply make use of a plank so as to avoid squashing or denting the turf. It’s important to ensure the successive rows are staggered to prevent the short edges from lining up.
4. Proceed by butting and pushing the edges to create a tight joint (make sure the turf is not stretched).
5. Use a wood saw or sharp serrated knife to trim any untidy edges. Remember to make use of a plank to ensure you do not walk directly on the turf.
6. Water the newly installed turf adequately to ensure the water penetrates the soil. However, do not turn it into a mud bath.

1. Place a post in the corner of the frame you created with the pegs and string. Measure and mark out 100mm from each side.
2. Dig out this soil to a depth of 700mm (watch out for cables or pipes). You should have a 300 x 300mm hole. Repeat for the other 3 corners.
3. Using a brick bolster, split a concrete block in two. Put a section of the block in each hole.
4. Get a length of post longer than you need and place one in each hole. You can cut it down later.
5. Create props on each post to hold them in place until you’re ready to add a cement mix. Check that they’re level. When you’re happy that they are, secure them in place with a concrete mix, making sure you create a slope in the concrete so that rainwater runs away from each post. When the concrete is set, remove the props.
6. Create a string line around each corner post and find the centre point between each. Place a timber batten at each point, ensuring that they’re not spaced any more than 1500mm apart.

1. Working from the corner where the deck will be at its highest above ground level, measure and mark on the post where the highest part of the frame will be.
2. Measure from the far side of one post to the opposite and cut sections of joist to size. Line up a piece of joist with the mark you made and temporarily secure it. Factor in a 2mm fall for every metre of decking so rainwater can run off.
3. Secure the frame to the other corner post, ensuring it’s at the right level. Do this for every side of the outer frame.
4. Using 100mm coach screws with washers hanging on the end, secure each end of the four sections of frame.
5. Mark out where the centre of the support posts will be and secure all of these posts to the frame, except the centre post.
6. Add your central support joists. These should run in the same direction as the deck boards will run. You’ll need to measure from the inside of the frame on one side to the inside of the frame on the opposite side. Attach the joist in the same way as you did for the other posts. Repeat so the centre post is in between two sections of frame and secure the posts with concrete.
7. Trim down all the posts to the correct height using a saw.
8. Add your weed-control fabric and weigh down with gravel across the entire area.

1. Measure 400mm from the centre of the outer frame and mark a line. This will be where the first joist is positioned. Repeat at 400mm intervals down the length of the frame – if the last one will be more than 400mm, add another joist to create enough support.
2. Attach a joist hanger to each end of the joist.
3. Place the joist in position so the centre lines up with the 400mm spacer mark.
4. Secure using external grade screws once you’re happy that the joist is flush with the frame.

On a hot summer’s day, we often seek our garden lawn as a cooling place to sit and get some relief from the sun. However, since artificial grass is made from plastic, lots of people ask whether it gets hot, or whether it stays like natural grass. The answer is, it’s somewhere in between.

Of course, we all know to stay in the shade in midday sun and this is when your artificial grass will be at its hottest. Unless it is an extremely hot say and your lawn is in direct sunlight, you should still be able to walk on your artificial grass. The best thing to do is test it using the back of your hand before anyone walks over it with bare feet or children go to play on it.

In the shade, artificial grass should always maintain a cool temperature, although it will never have that refreshing feel of cold grass on a hot day. It will also cool down extremely quickly as the day goes on, so if your grass does get too hot it shouldn’t be unusable for too long.

Artificial grass has to meet high safety standards and most are UV stabilised, which means that they can withstand high temperatures without melting or getting extremely hot. It’s worth remembering that hot countries like Dubai use artificial grass, so the occasional hot day in a British summer should be enough for artificial grass to handle!

How Much To Landscape A Garden?

Also known as a nation of gardeners, the UK is filled with individuals who take their outdoors seriously. As a result, it’s little surprise many people over here employ the services of expert landscape gardeners to help out with various tasks such as decking, building patios, ponds and reshaping their gardens to keep them in a top condition and make them a lot more useful. However, before you get started with your landscape gardening task, you’d like to figure out a estimate of the amount it’s going to cost. Let’s have a look!

Providing an accurate assessment of a generic landscape gardening project is almost impossible as gardens are all unique. A total refurbishment of a big garden will definitely run into thousands of pounds even before accounting for essential items like garden furnitures and planting. We’ll break them down to smaller elements of landscape gardening and give a rough estimate of the cost.

Firstly, a patio is an effective means of increasing your garden’s usability whose cost varies depending on the materials used. Generally, a patio will cost within the range of £70 to £90. This price may be higher in areas with greater demands like London.

A decking also serves the same purposes as a patio or paved area. However, it’s usually made of wood which delivers a much more natural feel perfect for the garden. The cost of decking varies largely depending on the wood incorporated. For instance, if you opt for a cheaper wood such as pine, the cost you can expect to pay would be within the range of 60 pounds to 80 pounds per square metre. However, for more quality and durable hardwood, you’ll have to pay about 200 pounds per square metre or more.

• Tongue and groove timber boards
• Boards for the ledges and braces, at least 20mm thick
• Nails
• Hammer
• Saws, including a circular saw
• Chisel
• Mallet

1. Cut your boards to size If you can’t buy boards at the right height and width for your door, cut the boards to length using a circular saw. Don’t forget to sand and treat any cut ends with timber preservative. Lay out the boards in the best arrangement for your shed door, with the inside of the door facing up.
2. Arrange the ledges and braces On most shed doors, you’ll probably need 3 boards across the back of the door to form the ledges. The ledges keep the door straight and keep the boards of the door together. The braces are the parts of the door that slope down to form a ‘Z’ shape between the ledges. Ensure that the braces are sloped up from the bottom and middle hinge to stop the door from sagging as the timber expands and contracts in the weather. Once you’re happy with the arrangement, mark the spots on the boards where they will meet and cut out of the housings using a chisel and mallet.
3. Put the door together Use clamps to pull the boards together and hold the ledges and braces in place. Nail from the front of the door through the boards and ledges to fix them. Secure the ledges and braces with screws; you may want to pre-drill and countersink holes to prevent the wood from splitting. Remember to treat them with preservative if you do.
4. Fix the shed door hinges Make sure you measure carefully before attaching the hinges, ensuring you know where the pin sits in relation to where the door opens.
5. Treat the door and add locks and handles Apply some wood oil, like linseed or teak oil, to help prevent water damage. Then add locks or handles to your shed to help keep it secure.
If you’d rather leave it to the professionals, there are plenty of specialists that will be able to make a shed door for you, or even put up an entire shed.