Find a Landscaper you can trust in Twickenham.

Properly erected fences shouldn’t require a great deal of maintenance. Any rotting boards can usually be replaced without replacing the whole panel. Timber fencing should be stained every 2-3 years. General maintenance is something you can carry out yourself, however, larger works may need a qualified professional to come in.

Our gardens are often our pride and joy, so we want them to look their best. If you notice that your garden is uneven, you’ll probably want to do something about it. But how do you level your garden or lawn? A gardener can help you do this and will get the best finish, but if you want to have a go at doing it yourself there are a few steps you can take. Before you start, make sure you’ve got all the following equipment to hand:

• String line
• 4 rods & string
• Tape measure
• Flat shovel
• Water sprinkler or watering can
• A rake
• Earthmoving and compacting equipment
• Spirit level
• 2 x 4 piece of wood
• Wheelbarrow
• Protective gloves and shoes

Then, you can get ready to level your garden.

1. Mark out the area Push 4 rods into the ground around the area you want to level out in a square or rectangle. Tie your string around the rods to connect them all together, ensuring that the string stays tight. Then use your string line to any of the 4 sides to check that it’s level. You’ll then need to measure the height from the ground to the string on all four sides to check how much you would need to adjust the ground to make it level. Make sure you take note of the high and low spots and measure the difference between these spots.
2. Water the ground to soften it If you want to level your lawn, or the part of your garden that you want to level has grass on it, you’ll need to uproot the ground underneath it. To make it easier to dig and lift out the grass, sprinkle some water over the area before you begin. It’s a good idea to do this over a few days to really soften it – but make sure you don’t do it so much that it becomes too heavy and soggy.
3. Remove the grass Push your flat shovel into the ground, around 3-6cm deep, then slide the shovel horizontally to lift out the soil and the grass on top. As you repeat this process around the entire area, make sure you try to lift out the soil evenly to avoid making your levelling task even harder.
4. Add soil Fill low spots with nutrient-rich soil and spread evenly over the area with a rake. If you’re levelling out a large area of your garden, consider renting earthmoving equipment to make it easier.
5. Flatten the soil Next you’ll want to compact the soil to protect it from erosion. If you’re working on a small garden or area of your garden, simply use your feet – get stomping on that ground! You could also use a rake, but for larger gardens consider hiring a compactor. Then, leave the soil to settle for around 3 weeks before doing anything. If you’re doing this in the summer, you can water it sparingly to keep it from drying out.
6. Adjust until you’re happy It might take you a few adjustments to get the level of your garden or lawn right. Use a spirit level along a long 2 x 4 piece of wood to see whether the ground is even, then adjust by adding a little more soil or removing soil until it’s at the level you want it.

That’s it. A gardener or landscaping company will be able to level your garden or lawn perfectly, so consider getting some quotes from local companies.

If your lawn edges are overgrown, it can make an otherwise well-cared for lawn look unsightly. Luckily, it’s easy to edge your lawn and make it look beautiful again. You should edge your lawn every spring and trim any overhanging grass you notice after mowing. How to edge a lawn There are different types of equipment you can use for different types of edging:

• Edging shears
• Half-moon edger
• Grass shears with a long handle
• Gardening knife
• Long rope or a plank of wood

Depending on how regularly you’ve maintained the edging of your lawn, you might want to do one of the following things:

• Annually in spring or if you’ve left the grass to get out of hand: Decide whether you want a straight or a curved edge along your lawn. If you want a straight edge, lay a plank of wood along the edge and use your half-moon edger to cut along. If you want a curve, lay a rope along the edge and cut along that. Or if you can still see the existing curve of the lawn, you can stick with that.
• After mowing: Use long-handled shears to trim the grass the mower couldn’t reach. If you want to make it look extra tidy, collect up the cuttings and put them on your compost heap or dispose of them.
• Overgrowing grass onto paths: Use a sharp gardening knife to cut the pieces of turf that are growing over the path and pull them away.
• When your lawn is flush with the path: Snip a clean edge along your path with your long-handled grass shears to make it look neat and tidy.
• If you’d rather a low-maintenance option: Spiked metal sheeting is a good material to use to keep your lawn’s edges at bay. Fix it in the ground along the edges to keep the outline of your lawn and stop it from growing into your borders.

The best way to keep your lawn edges looking fabulous is to keep them maintained. Remember to give them a little trim every time you mow your lawn to be the envy of all your neighbours.

Laying a lawn is a task that’s best left to the professionals especially if you don’t know what you’re doing. However, if you can follow a simple logical process, you’ll save yourself a lot of headache – simply start from the edge and work inwards. If you’re looking to lay your lawn by yourself, then you’ve come to the right place! In this post, we’re going to consider the processes involved in lawn installation in order to ensure your project turns out a success. Let’s take a look!

Firstly, the tools you’re going to need to lay your lawn includes the following – sturdy boots, gardening gloves (should be thick), wheel barrow, garden fork or rotovator, landscaping rake, laying boards, knife or edge trimmer, hosepipe and broom.

1. Start from the outside edge. Install the initial strips horizontally overlapping the boundary a bit (trim the back once done). Press down carefully to make sure there’s a good contact with the soil (make sure not to squash the lawn).
2. Proceed to lay the adjacent pieces till the first row of the lawn along the entire edge is completed.
3. Continue with the next row. If there’s a need to stand on the laid turf, simply make use of a plank so as to avoid squashing or denting the turf. It’s important to ensure the successive rows are staggered to prevent the short edges from lining up.
4. Proceed by butting and pushing the edges to create a tight joint (make sure the turf is not stretched).
5. Use a wood saw or sharp serrated knife to trim any untidy edges. Remember to make use of a plank to ensure you do not walk directly on the turf.
6. Water the newly installed turf adequately to ensure the water penetrates the soil. However, do not turn it into a mud bath.

Scarification is the name given to the process where you remove excess thatch and moss from your lawn to encourage it to grow and look healthy. Although it sounds difficult, it’s actually pretty easy – simply grab a sturdy rake and apply moderate pressure to rake out moss, thatch and dead grass. Then collect it up and add to your compost heap if you have one. You can also use a petrol or electric rake, but you just want to tease out the moss and thatch. Don’t be tempted to go deep into the grass, as this could damage your lawn. So when should you scarify your lawn? The experts say that the best time is in the autumn, when the grass is actively growing and it’s not too hot, cold or dry. Most of summer’s weed seeds will have gone, so you won’t encourage weeds to grow in the raked-up soil. This soil also makes an ideal seed bed for over seeding with new grass seed, so that’s why you don’t want to get weeds in there as well. However, you may also carry out light scarification in the spring – usually around April. Make sure you don’t go too far though – as you will end up with a rather disfigured lawn if you scarify too heavily and the dryness of summer stops the lawn from recovering. It’s also best to scarify your lawn in the spring if the following apply:

• If you couldn’t do it the previous autumn – if you keep putting it off, you might end up with extreme moss and weed growth
• If your lawn is shaded – these areas will thin over winter and start to thicken from spring onwards, so if you scarify in the autumn you’ll make your lawn even thinner.
• If your lawn is under trees – pair the shade from the trees with the fall of leaves in the autumn and your grass won’t be healthy, but in the spring the trees are bare, allowing lots of light onto your lawn to help it grow.

Regular maintenance is vital for keeping a garden looking its best. By carrying out regular gardening work, you can ensure that your garden is as functional as possible. Regular garden maintenance work could also save you money, as it is better to detect problems such as overgrown trees or rotten fencing early.

Is there a hole in your asphalt driveway you feel you can repair yourself? If it’s something you know you can confidently do then this step by step guide is just for you. If otherwise, then we’d recommend you hire the services of a reliable professional who can guarantee the best results while also saving you some time and extra money that could result from possible errors. In this article, we’d go over the reparation process of an asphalt driveway with a hole in it.

✓ Get the necessary tools. You’re going to need a broom ( to clean the area), caulking gun ( to fill the hole), a hand tamp a plate compactor or a hammer ( to level the filled in hole) and a weeding glove (just in case there are weeds growing in the hole).

✓ Prepare the area. Do this by weeding the plants or weeds that might have grown inside the hole and identify your asphalt filler.

✓ Wet your soil, if necessary. It’s important to note that this is only necessary if your soil is dry to help the filler stick properly.

✓ Fill in deep holes. If the hole goes down about 3 to 4 inches or more, simply fill it with any material like rocks, clay etc.

✓ Apply the asphalt filler. Fill the hole with the asphalt filler to about half an inch higher than the surface of the driveway.

✓ Level the filler. For a large hole, make use of a plate compactor or a hand stamp, but a hammer will be sufficient for smaller holes.

✓ Cover the hole, if necessary. If your home isn’t level, covering your hole with a piece of plywood is advisable.

✓ Clean off the seal. After the asphalt looks done and in place, simply brush away the debris from the seal to finish off the project.

Patios do not require lots of maintenance. They will only need occasional cleaning to make sure that the material keeps its original appearance. It's always best to clean your patio with a pressure washer and occasionally tap each slab or brick just to check the sand underneath hasn't washed away.