Find a Landscaper you can trust in Dalkeith.

• Paving slabs – old or cheap ones are fine
• Timber for the frame and legs
• Type 1 MOT hardcore

1. Mark out the area as we explain in ‘How to lay decking’. Then, dig to 200mm below where you want to surface of the decking to be.
2. Add a 50mm layer of hardcore and make sure it’s compact.
3. Build the decking sub-frame as we describe in ‘How to build a deck frame’.
4. Lay out paving slabs along the edges and in the centre of the area. This will help to spread the weight of the decking.
5. Set the decking frame on the slabs, checking for high or low points and adding off-cuts of timber where needed. Don’t forget to sand and seal these off-cuts with decking preservative.
6. Add your joists and then the deck boards, leaving the recommended gaps of expansion of between 5-8mm.

Driveway surfacing materials like concrete, asphalt and clay brick usually crack because they’ve been exposed to extreme temperatures or put under high pressure. It’s important to repair driveway cracks before they get worse and cause damage to vehicles and perhaps others to trip on raised cracks.

1. How to build a shed base out of paving slabs
   • Mix sand and cement together to make mortar or use a pre-mixed one
   • Use a trowel to lay mortar for 1 slab at a time on the sub-base and lift a damp-sided slab onto the mortar, using a piece of timber and club hammer to tap the slab into position carefully. Continue to lay the first row of slabs
   • Make equally-sized spacers in all the joints in the slabs to ensure they’re the same size, checking it’s level as you go along
   • Next lay slabs along the two adjacent outer edges, filling in the central area row by row
   • Leave the mortar to set according to the instructions or for at least 48 hours before filling in the joints with mortar or paving grout
2. Building a shed base from concrete
   • Create a wooden frame around your shed base area (also called formwork) to stop the concrete from spreading
   • Mix pre-mixed concrete with water or use 1 part cement to 5 parts ballast
   • Wet the sub-base using a watering can with a rose on the end
   • Pour the concrete onto the framed base starting in one corner
   • Push the blade of a shovel up and down in the edges of the concrete to get rid of air bubbles
   • Use a rake to spread the concrete, leaving it around 18mm higher than the top of the frame. Work in sections of around 1-1.m²
   • Compact the concrete using a straight piece of timber that’s longer than the width of the base. Move the timber along the site, hitting it along at about half of its thickness at a time until the surface is evenly ridged
   • Remove excess concrete and level the surface by sliding the timber back and forwards from the edge that you started. Fill in any depressions and repeat until even
   • Run an edging trowel along the frame to round off exposed edges of the concrete and prevent chipping
   • Cover the concrete with a plastic sheet raised on wooden supports to allow slow drying. Weigh it down with bricks
   • Once the concrete is set, you can install your shed and remove the wooden frame with a crowbar

Moss, mushrooms and weeds are all problems that many homeowners face on their lawns. Luckily, with a bit of maintenance, there are ways you can get rid of these unwanted organisms and prevent them from coming back. Getting rid of moss A simple way to remove moss from your lawn is by scarification. This basically means that you vigorously rake your lawn, but only do this in the autumn when the grass is actively growing and it’s not too hot, cold or dry. However, you can also use specific weedkillers to control moss on your lawn, and most of these should be applied when the moss is actively growing. Apply in fine weather by hand or with a push-along spreader, making sure not to apply too much as you could kill off the grass too. Check the instructions, as some will require watering after 48 hours if it’s not rained. Then, get into a scarification routine to help prevent moss growth. Removing mushrooms from your lawn If you’ve got mushrooms in your lawn, it usually means that your lawn is damp and shaded, so it never dries out, and is organic waste-rich. There could be a drainage problem with your lawn that is encouraging mushroom growth, so it’s important to investigate why the mushrooms are growing to prevent them from returning once you’ve removed them. To get rid of mushrooms in your lawn, make sure you scarify your lawn and get rid of all the moss, thatch and dead grass that comes up. If you leave it, this is heaven for mushrooms to grow in. If your lawn is shaded, try to prune and thin surrounding trees to offer it more light. If you do all of these things, it will prevent mushrooms from growing in the future, and then it might be worth using a fungicide to get rid of the mushrooms that are there. But if you just do this step, it’s likely the mushrooms will just come back. How to get rid of weeds To get rid of weeds from your lawn, you can use selective weedkillers that will just kill the weeds and leave your grass alone. But if you’d rather not use weedkiller, you can get rid of weeds from your lawn manually. For large, deep-rooted weeds like dandelions or plantains, use a trowel to lever them out, ensuring that you get the whole plant including its roots. Then use compost to fill the hole it leaves behind, pushing it deeply into the hole. Sprinkle with fresh grass seed, cover with extra compost and water. Make sure you keep the area damp until the seed has germinated. To prevent moss, mushrooms or weeds from returning, the best things to do are:

• Scarify your lawn in the autumn, and lightly in the spring if necessary
• Seed your lawn in the autumn if you need to
• Try to keep trees trimmed and pruned as much as possible to reduce shade
• Use a pre-emergent weedkiller in the spring to catch them before they grow and handpick any that come through
• Mow your lawn regularly in the spring and summer, being careful not to remove more than a third of grass at a time, then before winter give it one last mow and a fertilisation treatment

Patios do not require lots of maintenance. They will only need occasional cleaning to make sure that the material keeps its original appearance. It's always best to clean your patio with a pressure washer and occasionally tap each slab or brick just to check the sand underneath hasn't washed away.

When your driveway is suffering from depression, it becomes unsafe for driving (a danger zone) and ugly - no homeowner wants that! Unfortunately, most driveways won’t hold flat for long as they tend to develop cracks and potholes pretty quickly. Here, we are going to take you through how to fill asphalt driveways’ depression so as to ensure the sinkholes in your driveway poses no threat to you or your loved ones, while also beautifying your property. The approach to be used depends on the intensity of the depression. If its only a few cracks and holes, this can easily be repaired with some equipment. But if otherwise is the case, then calling a reliable professional will be your best bet. In this article, we’ll show you how to repair dips in your asphalt driveway relatively quickly.

✓ Pick a date with warm and sunny weather. This is because if you work in a cold weather, chances are the materials will freeze and hence, unusable. So find a day when the temperature will over 50 degrees Fahrenheit and below 80 degrees Celsius and when there would be no rain. We’ll advise a day between May to October.

✓ Prepare the area. Remove all loose stones, soil, dirt as well as vegetation from the holes. Once done, you can then proceed to washing the area with a pressure washer or sweep with a broom.

✓ Apply a thin mixture of asphalt to the area. Use a flat stirring stick to coat the low driveway area with a thin mixture of asphalt.

✓ Tamp the asphalt repair mix. Purchase the right kind of asphalt to repair the driveway. Fine aggregate asphalt mixture is more suited to filling small holes, whereas the coarse aggregate is more suited to filling larger holes. Apply layers ( about 2 inches each time) of the asphalt repair mix to the sunken area and use a shovel to give it a smooth finish. Once done, simply make the area smooth and protect it with a piece of plywood. Do not walk or drive on the area for a couple of days.

The best way to build a fence depends on what style it is, as different types have different components. However, fencing made up of posts and panels is pretty common. To put this up, you’ll need to start by measuring out and digging holes for your fence posts. Then you’ll need to fit the panels between them and use concrete to secure the posts in the ground.

1. Calculate the surface area for your decking Multiply the length (L) of your decking area by the width (W): L x W = Decking Surface Area (DSA) in m² 10 x 6 = 60m²
2. Work out the coverage of your deck boards Add your deck board width (DBW) to the expansion gap length (EGL), then add the deck board length (DBL) to the expansion gap width (EGW). Then multiply these numbers. (DBW + EGL) x (DBL + EGW) = Single Board Coverage (SBC) 0.144m + 0.005m = 0.149m 2.4m + 0.003m = 2.403m 0.149 x 2.403 = 0.358m²
3. Calculate the number of deck boards you need Multiply the SBC by 1.1 to allow for 10% wastage. Then, divide the DSA by the SBC. DSA / SCB x 1.1 = Total number of boards required 60m² / 0.358m² x 1.1 = 184.36 boards – so round up to 185 so you’re not left short.