Find a Landscaper you can trust in Dunkeld.

• Decking joists
• Coach screws
• Coach bolts
• Combi drill
• Socket set
• A saw suitable for your project and the thickness of the timber
• Pencil
• Decking preservative
• Sandpaper or sander

1. Measure your deck frame and cut to size if necessary.
2. Make 2 pencil marks on each end of the frame’s 2 outer joists to mark where the coach screws will go. They need to align with the centre of the adjoining outer joist. Then, use a flat wood drill bit to drill recesses into each mark. Make them the same depth of the screws that your using’s head and wide enough for a ratchet or socket to tighten them.
3. Using a thinner drill bit, line up the outer joists and drill a pilot hole through the middle of the recess. These pilot holes act as a guide for the screws and stops them from splitting the wood.
4. Fit the coach screws with either a drill driver or socket and ratchet.
5. Repeat the process for the inner joists once you’ve assembled the outer frame.

Laying artificial grass is a popular project – it’s a great way to create a smart, low-maintenance garden. There are plenty of professionals around who are experts at installing artificial grass, but it’s possible to DIY too if you’re feeling confident.

Lots of homeowners choose to replace their existing turf with artificial grass, so lay it on soil. To do this, start by clearing the area of any greenery or turf. Then remove any extra soil to a depth of about 40mm. You might want to leave the centre of your area slightly higher than the edges for a more natural look.

Next, you need to add a weed membrane and a sharp sand sub-base. It doesn’t really matter which one of these you do first, but you might find it easier to lay the weed membrane first and then use the sand to weigh it down, to a depth of about 35mm. Use a rake and plank to make the sand level, and compact it with a plank and heavy hammer. It doesn’t need to be completely flat – gentle slopes are fine. The weed membrane should overlap joints by 300mm.

After you’ve done this, you can lay your grass. Roll it out, trim it to size and fasten it in place. Make sure the ends of the grass rolls are staggered so they don’t end in a line. Lay the artificial grass with the pile (the strands) leaning towards the house so it looks nice and full when you’re looking out from the house. If you’ve decided to use edging boards, you can nail the grass into the tops of the boards. Or, if you haven’t, use ground pins to anchor it into the soil. Brush the grass and you’re done!

It’s a good idea to talk to your neighbours before you start any work to avoid confusion along the way. But if the fence is definitely your responsibility and on your property, there’s no legal obligation to notify them. It’s also a myth that you need to erect a fence with the flush side without posts facing your neighbour’s property.

1. How to build a shed base out of paving slabs
   • Mix sand and cement together to make mortar or use a pre-mixed one
   • Use a trowel to lay mortar for 1 slab at a time on the sub-base and lift a damp-sided slab onto the mortar, using a piece of timber and club hammer to tap the slab into position carefully. Continue to lay the first row of slabs
   • Make equally-sized spacers in all the joints in the slabs to ensure they’re the same size, checking it’s level as you go along
   • Next lay slabs along the two adjacent outer edges, filling in the central area row by row
   • Leave the mortar to set according to the instructions or for at least 48 hours before filling in the joints with mortar or paving grout
2. Building a shed base from concrete
   • Create a wooden frame around your shed base area (also called formwork) to stop the concrete from spreading
   • Mix pre-mixed concrete with water or use 1 part cement to 5 parts ballast
   • Wet the sub-base using a watering can with a rose on the end
   • Pour the concrete onto the framed base starting in one corner
   • Push the blade of a shovel up and down in the edges of the concrete to get rid of air bubbles
   • Use a rake to spread the concrete, leaving it around 18mm higher than the top of the frame. Work in sections of around 1-1.m²
   • Compact the concrete using a straight piece of timber that’s longer than the width of the base. Move the timber along the site, hitting it along at about half of its thickness at a time until the surface is evenly ridged
   • Remove excess concrete and level the surface by sliding the timber back and forwards from the edge that you started. Fill in any depressions and repeat until even
   • Run an edging trowel along the frame to round off exposed edges of the concrete and prevent chipping
   • Cover the concrete with a plastic sheet raised on wooden supports to allow slow drying. Weigh it down with bricks
   • Once the concrete is set, you can install your shed and remove the wooden frame with a crowbar

Gardens need regular maintenance and without it they can get really out of hand. When you’re thinking about how much gardeners charge, you should bear in mind the state of your garden and whether you need a one-off tidy up or want a regular ‘manicure’ of your garden to keep it looking neat and tidy. Gardeners generally charge in two different ways for their work depending on the job: with an hourly rate or with a fixed price. Generally, gardeners will charge an hourly rate of between £20 - £40 depending on their experience, the job and where you are in the country. They may also charge a minimum call-out charge since a lot of their day will include unpaid travel from job to job. If you don’t need your gardener for a full day, for example if you just need your lawn mowed, then they will probably charge a fixed rate. It’s unlikely to have anything to do with their hourly rate. We’ve found that the average fixed cost of a gardener is around £250 - but this of course includes small jobs like weeding and mowing to larger jobs like pulling out shrubs and replanting, so you may find that your gardener charges more or less than this. Bear in mind that most gardeners will charge a price that doesn’t include waste removal, since lots of people have compost heaps or garden waste bins. So if you need them to take the garden waste away, expect another £100 - £200 on top of your quote.

Uneven lawn? Well, for an outdoor space which looks great and serves its purpose throughout the year, there’s a need to learn how to level your garden. While its best left for a professional to handle, there are also some simple steps you can follow to ensure your DIY task turns out a success whether you’re preparing to lay a patio or deck, landscaping the whole space or tackling a lumpy lawn. A level ground comes with a bunch of benefits which includes maximizing the functions of your yard, helping with drainage while also enhancing your property’s curb appeal. Good news is, you can level your sloping lawn by hand. Want to know how? In this post, we’re going to take you through the processes involved in levelling an uneven lawn. Let’s take a look!

You can simply level your lawn using your hand if you aim to make your lawn a more even surface or to install a patio or deck. If your goal is only to make the lawn more even, you should have it in mind that, even though lumps and bumps aren’t always pleasing for most people, it can actually create a good drainage for your home.

Top dressing is the solution for depressions that are about 2cm to 3cm deep. To resolve this, simply get a top dressing mixture or make yours using two parts of sand and topsoil and a single part of compost. Use this to fill out the depression evenly and make compact using a rake or your feet, then water. Leave this for two days before applying grass seed alongside a thin layer of topsoil, then water as needed.

If you have a deeper depression, simply dig out to around 4cm to 5cm and remove any lumps of soil or stones. Once done, proceed to top dressing as explained above and grass seed to fill out the bald spot.

1. Unroll your two pieces of artificial grass, ensuring that the pile is running in the same direction. Fold over each piece by about 300m.
2. To get the perfect seam, cut at least 3 tufts back, ensuring that you don’t trim any grass blades.
3. Either remove the backing on your self-adhesive tape and unroll it down the centre of the join, or roll it out ensuring that the shiny side is down then fix at either end with adhesive.
4. Fold over the grass onto the tape and bring each piece together, ensuring there’s a 2-3mm gap at the seam.
5. Where the pile runs over the edge of the seam, fold over the artificial grass.
6. Apply a small amount of adhesive under the edge of the first section of grass with a mastic gun, then add some to the front edge to stick the second piece.
7. Bring the seam together, ensuring that you don’t get any grass blades stuck. Place a plank with some heavy objects on over the join to ensure that it dries securely.

If there’s a fence dividing yours and your neighbour’s properties that needs maintaining or replacing, you’ll want to know who owns it. Start by checking your deeds to see if there’s an existing boundary agreement. If there isn’t, have a chat with them to see if you can come to an arrangement yourselves.