Find a Landscaper you can trust in Builth Wells.

It’s a good idea to talk to your neighbours before you start any work to avoid confusion along the way. But if the fence is definitely your responsibility and on your property, there’s no legal obligation to notify them. It’s also a myth that you need to erect a fence with the flush side without posts facing your neighbour’s property.

• Have a step tread width of 900mm – if you don’t want them that wide, they should be no less than 760mm
• Add a central step riser to stairs wider than 900mm to prevent them buckling
• Add a step depth (the vertical distance between each step) of between 150 and 180mm if building your own riser, so the steps are at a comfortable depth

• Step treads (the actual step themselves)
• Step risers
• Coach screws
• Deck screws
• Saw
• Drill

1. Make sure the ground where you want to put your steps is level and firm. If it’s not, consider laying concrete or paving slabs to provide a secure surface for your steps to sit so they don’t sink.
2. Grab some joist off-cuts and cut them to the same width as your step treads. Attach them to the step risers at the top and bottom using countersunk coach screws.
3. Place the steps against the sub-frame of the deck; if you’ve put slabs down for support, make sure the steps sit in the middle of them. The longest edge of the stair riser should be on the slabs, and the short edge against the deck. Drill pilot holes through the step and sub-frame joist, then screw the step to the sub-frame with more coach screws.
4. After drilling pilot holes, screw the treads into the risers at each end with deck screws.
5. If you don’t want gaps between each stair, you can add joist off-cuts or deck boards. Measure the height and depth of the gap, then screw the off-cut or board into the step riser with two screws at each end.

1. Remove any existing fascia boards Remove the fascia boards and the old felt if you’re re-felting.
2. Measure the shed roof Measure the roof, taking into account that you should leave around 50mm for overlaps at the eaves and 75mm at the gable ends. You’ll probably need 3 pieces of felt, but some smaller sheds only need 2.
3. Apply felt to the roof Once you’ve cut the felt to size, apply the each piece to the roof, pulling it tight. Then nail along the length of the roof at 100mm intervals. For nails at the bottom edge, they can be wider – around 300mm. If you’re adding a piece of felt in the middle of the shed along the apex, fix it using adhesive, then nail it at the lower edge at 50mm intervals.
4. Tidy up the overhangs Fold down the felt at each overhang and nail it securely. Cut a slit in the overhang at the apex using a pen knife, then fold that down and nail at 100mm intervals along the gable. If you like, you can add fascia boards to keep the shed looking neat. Use wood nails to secure them and then trim away any excess felt.

1. Place a post in the corner of the frame you created with the pegs and string. Measure and mark out 100mm from each side.
2. Dig out this soil to a depth of 700mm (watch out for cables or pipes). You should have a 300 x 300mm hole. Repeat for the other 3 corners.
3. Using a brick bolster, split a concrete block in two. Put a section of the block in each hole.
4. Get a length of post longer than you need and place one in each hole. You can cut it down later.
5. Create props on each post to hold them in place until you’re ready to add a cement mix. Check that they’re level. When you’re happy that they are, secure them in place with a concrete mix, making sure you create a slope in the concrete so that rainwater runs away from each post. When the concrete is set, remove the props.
6. Create a string line around each corner post and find the centre point between each. Place a timber batten at each point, ensuring that they’re not spaced any more than 1500mm apart.

1. Working from the corner where the deck will be at its highest above ground level, measure and mark on the post where the highest part of the frame will be.
2. Measure from the far side of one post to the opposite and cut sections of joist to size. Line up a piece of joist with the mark you made and temporarily secure it. Factor in a 2mm fall for every metre of decking so rainwater can run off.
3. Secure the frame to the other corner post, ensuring it’s at the right level. Do this for every side of the outer frame.
4. Using 100mm coach screws with washers hanging on the end, secure each end of the four sections of frame.
5. Mark out where the centre of the support posts will be and secure all of these posts to the frame, except the centre post.
6. Add your central support joists. These should run in the same direction as the deck boards will run. You’ll need to measure from the inside of the frame on one side to the inside of the frame on the opposite side. Attach the joist in the same way as you did for the other posts. Repeat so the centre post is in between two sections of frame and secure the posts with concrete.
7. Trim down all the posts to the correct height using a saw.
8. Add your weed-control fabric and weigh down with gravel across the entire area.

1. Measure 400mm from the centre of the outer frame and mark a line. This will be where the first joist is positioned. Repeat at 400mm intervals down the length of the frame – if the last one will be more than 400mm, add another joist to create enough support.
2. Attach a joist hanger to each end of the joist.
3. Place the joist in position so the centre lines up with the 400mm spacer mark.
4. Secure using external grade screws once you’re happy that the joist is flush with the frame.

Overseeding your lawn is an essential part of keeping your lawn looking its best. It’s also known as reseeding, and helps to repair damaged areas that might have been caused by a harsh summer or winter. It’s best to overseed your lawn during the spring or autumn, when the temperature is mild but there’s still a fair amount of rainy days to help the grass seed grow. To prepare your lawn for overseeding, you should do the following things around 1-2 weeks beforehand:

• Weed the lawn by hand or using a weedkiller (make sure you leave enough time to do this according to the instructions)
• Remove stones and large twigs
• Scarify your lawn to remove moss and loosen soil
• Fertilise the soil with a quick-release fertiliser

Once you’ve taken these steps, you’re ready to start overseeding your lawn.

1. Mow your lawn to around 25mm in length.
2. Water the soil so it’s moist but not too damp.
3. Sprinkle your new grass seed evenly over the lawn, but apply more in patchy or thin areas. Generally gardeners say to use 35g per square metre, but up to 50g on thin areas.

When you’re finished, give your lawn a final water, and do this every day until the new grass is established – particularly if it’s not rained. Just make sure you don’t overwater it. It’s also a good idea not to walk on your lawn for around 2-3 weeks after you’ve overseeded it.

Everyone wants their garden to feel luscious, spacious and welcoming. But if you’ve got a small garden, it might feel like there’s no way to stop it looking cramped and unappealing. Luckily, there are ways to make a small garden look bigger – and they don’t have to cost the earth. Plant high You can’t expand your garden outwards, but you can go upwards. Harness your neighbours’ walls and fences to plant climbers and trailing plants to add height to your garden. Hanging baskets are a great option too. By using all the space available to you, it creates the illusion that your garden is bigger than it really is. Remove bulky bushes Now you know to plant high, you might realise that there are some shrubs and bushes that need to go. Large bushes spread out and take up too much space, making it feel crowded. If you’ve got a bush for security reasons, consider replacing it with a fence and adding climbers or tall plants around it like we suggested. Create depth An easy way to make a small garden look bigger is to create depth with different textures. Around borders, plant fine-textured plants in the background with course, large-leafed plants in the foreground to give the impression of a deeper space. This is a great idea for shallow, sloping gardens. You can use vibrant colours in the front with a backdrop of green to draw the eyes back. Blend into the background Consider using similar colours, shapes and plants to blend into the view beyond your garden, so it blurs where the boundary of your garden is. If plants and trees creep over from your neighbours’ gardens, don’t trim them back – merge them with your own garden’s style. Stick with a few favourite plants Another mistake people make when trying to make a small garden look bigger is they plant too many different things. This makes your garden feel cluttered, so stick with seasonal combinations; a good rule of thumb is to have at least 3 different flowering species at any time.