Find a Landscaper you can trust in Craven Arms.

1. Remove fascias and trims Unscrew or prise off the screws and nails fixing the trims and fascias to your shed.
2. Take off doors and remove windows Unscrew hinges from doors and take them off. Remove all metalwork once the door is off. If you’ve got frames on your windows, unscrew these, and remove the panes. Be extra careful if your windows are made of glass.
3. Take off the roof Prise off the tacks from the roofing felt and take the felt off – you can’t reuse it, so you’ll need to throw it away. Unscrew the screws on the roof boards and slide them off the shed’s frame – you might need a friend to help you do this.
4. Take out the roof brace (optional) If your roof has a brace, unscrew the brackets that hold it to the side of the shed. Remember not to lean on anything once you’ve taken the brace off as the walls might be wobbly.
5. Unscrew the frame from the floor Remove all the screws that are holding the shed to the base, remembering not to lean on the walls.
6. Unscrew the frame corners Starting at the corner of the front gable, remove the screws where the panels meet. Once a panel is free, lift it carefully out of the way so you can carry on with the others.

1. Mark out the area and dig the top layer of soil, trying to get the ground as flat as possible.
2. Build a timber frame to size.
3. Measure out 4 rows of 3 blocks to create good weight distribution and lay in place.
4. Underneath each block, dig around 50mm wider than the blocks and about 150mm deep. Fill the hole with pea gravel until it’s flat.
5. Place timber planks along the rows of blocks and see how level it is. Add or remove blocks where necessary. If it’s only a small difference, use shingle underneath the timber until it’s level.
6. Nail your timber shed base to the timber planks to create a sturdy base for your shed.

How To Plan A Landscape Garden

If you’ve decided to go for a landscape garden, this might imply putting in new gardens entirely or probably just coming up with a planting plan for the current year. However, because you want a beautiful landscape garden doesn’t mean you can just go out, get a couple of plants and decide to plant them anywhere that looks good to you once you get home.

For a much better landscape garden, doing some proper landscape garden planning can go a long way to help you get the results you desire. So how do you plan a landscape garden?

• Set Goals

The first step is to determine how you want the garden to feel and look, how it’s going to be used or what’s going to be used for as well as how you’ll work to boost the small ecosystem.

• Site Plan

Identify what you already have on the site like the plants, paths, gardens etc, and draw them out perhaps on a graph paper. Once done, you can make some photocopies and start playing with different ideas.

• Site Analysis

Carry out an in depth site analysis to identify the areas that’s sunny and shady areas as well as the ones in between. This way, you can figure out the best place to put the plants and other items.

• Functional Diagrams

This is stage at which you go through both the site plan as well as site analysis and start to identify the right spots to position the landscape garden’s items.

• Planting Plan

Here, you’ll decide which plants you’ll like to use on your landscape garden while also identifying what plant goes where. You’ll have to draw them at size close to what they’ll grow to become, so as to ensure there’s sufficient space for them once they grow big and tall.

1. How to build a shed base out of paving slabs
   • Mix sand and cement together to make mortar or use a pre-mixed one
   • Use a trowel to lay mortar for 1 slab at a time on the sub-base and lift a damp-sided slab onto the mortar, using a piece of timber and club hammer to tap the slab into position carefully. Continue to lay the first row of slabs
   • Make equally-sized spacers in all the joints in the slabs to ensure they’re the same size, checking it’s level as you go along
   • Next lay slabs along the two adjacent outer edges, filling in the central area row by row
   • Leave the mortar to set according to the instructions or for at least 48 hours before filling in the joints with mortar or paving grout
2. Building a shed base from concrete
   • Create a wooden frame around your shed base area (also called formwork) to stop the concrete from spreading
   • Mix pre-mixed concrete with water or use 1 part cement to 5 parts ballast
   • Wet the sub-base using a watering can with a rose on the end
   • Pour the concrete onto the framed base starting in one corner
   • Push the blade of a shovel up and down in the edges of the concrete to get rid of air bubbles
   • Use a rake to spread the concrete, leaving it around 18mm higher than the top of the frame. Work in sections of around 1-1.m²
   • Compact the concrete using a straight piece of timber that’s longer than the width of the base. Move the timber along the site, hitting it along at about half of its thickness at a time until the surface is evenly ridged
   • Remove excess concrete and level the surface by sliding the timber back and forwards from the edge that you started. Fill in any depressions and repeat until even
   • Run an edging trowel along the frame to round off exposed edges of the concrete and prevent chipping
   • Cover the concrete with a plastic sheet raised on wooden supports to allow slow drying. Weigh it down with bricks
   • Once the concrete is set, you can install your shed and remove the wooden frame with a crowbar

1. Remove any existing fascia boards Remove the fascia boards and the old felt if you’re re-felting.
2. Measure the shed roof Measure the roof, taking into account that you should leave around 50mm for overlaps at the eaves and 75mm at the gable ends. You’ll probably need 3 pieces of felt, but some smaller sheds only need 2.
3. Apply felt to the roof Once you’ve cut the felt to size, apply the each piece to the roof, pulling it tight. Then nail along the length of the roof at 100mm intervals. For nails at the bottom edge, they can be wider – around 300mm. If you’re adding a piece of felt in the middle of the shed along the apex, fix it using adhesive, then nail it at the lower edge at 50mm intervals.
4. Tidy up the overhangs Fold down the felt at each overhang and nail it securely. Cut a slit in the overhang at the apex using a pen knife, then fold that down and nail at 100mm intervals along the gable. If you like, you can add fascia boards to keep the shed looking neat. Use wood nails to secure them and then trim away any excess felt.

Everyone wants a good-looking lawn! If you’re wondering the best time to scarify your lawn, then you’ve come to the right place! In this post, we’re going to consider this in order to help you make the best-informed decision possible. Let’s take a look!

The short and simple answer to this question is when your grass is actively growing. This is the best time to scarify a lawn as it enables it to recover faster once it has been scarified. What’s more? The conditions also have to be appropriate as extreme weather condition, be it too cold, too warm, too dry or too hot, will hinder the quick and proper recovery of your lawn. It’s also important to take note that scarifying of a lawn is going to leave the soil exposed which makes way for weed and other unwanted plants to grow.

During the year, there are two different times which tends to provide the most ideal conditions to scarify a lawn. The first of these periods is late March or April when the spring is in the air and your grass receives all the warmth and moisture it needs to thrive. It’s also advisable not to wait till too late in the spring as right after this period comes the heat and dryness of summer. Furthermore, the lawn shouldn’t be scarified too heavily during the spring as summer usually comes with weed seeds which means your grass won’t recover fast enough and weeds will quickly make way for themselves.

If you wish to scarify your lawn heavily, then the perfect time to do this would be in September or October – during autumn. During this period, the summer weed seeds would be gone and the grass will grow properly.

Chances are at some point you’d probably given a though about how steps would fit in perfectly in your garden, except of course, your yard and garden is flat. Adding steps and gardens makes it a lot easier to get around your yard while also enhancing its curb appeal. In order to avoid the cost of hiring a professional to get the task done, you might be tempted to make it a DIY task. However, if you lack the required skill and confidence to pull this off, we’d strongly recommend you call in a professional so as to avoid costly errors. In this post, we’re going to take you through the garden steps building process. Let’s take a look!

1. Measure the vertical height of the slope by marking it with two parallel lines. Once done, proceed by connecting a string line to the slope’s top and hold it in a horizontal way, take a measurement of the flight’s length and breadth. Divide the measurement by 200mm to get the number of steps that’ll be required. Then proceed to divide the number by the height to identify the depth of each step.
2. Working downwards from the flight’s top, dig the step shapes and also dig a shallow trench and install a concrete foundation.
3. Enable the foundation to harden by leaving it for about 48 hours, then install two courses of bricks on the concrete strip and use gravel to backfill.
4. With the help of a trowel, apply mortar to the top of the brickwork. Place the first slab on the mortar bed and press down. Then, make use of a spirit level to make sure that the steps are level.
5. On the back edge of the first tread, you should proceed to build the second rise, backfill and install the slab to form the second tread – just like the previous step. Repeat this process until you’ve gotten to the top of the flight.

Properly installed wooden decking will not need a lot of maintenance. Most manufacturers recommend regularly brushing leaves and dirt off the deck, and a yearly cleaning and staining procedure. This will keep the wood in the best condition. Fluids and treatments are readily available from all DIY shops and stores.