Find a Landscaper you can trust in Wellington.

Garden slabs are a joy to behold but only when done the right way. Well, the installation of paving slabs shouldn’t be exceed digging a little here and there, buying a small amount of mortar and pressing down the garden slab, right? Absolutely not! But we must admit how great it would have been if only it were that easy in real life. Let’s be honest, in reality, laying garden slabs does not only require you to prepare your sub-base painstakingly and mix your mortar using the appropriate materials, but you’d also have to work with accurate and precise paver placements to guarantee the patio’s longevity. Consequently, this happens to be a stressful and quite tricky challenge. If you lack the required confidence to pull this off, we’d recommend you hire the services of a seasoned professional who can guarantee the best results and also save you time and extra cash that may result from possible costly errors. In this guide, you’d gain more insight into the garden slabs laying process.

To get started, you’ll need sharp sand, cement, shovel, wheelbarrow, pointing trowel, rubber mallet, spirit level, jointing compound, hard-bristled brush and tarpaulin.

1. Mix a layer of mortar for each paver.
2. Apply the mixed mortar onto the sub base by using the trowel.
3. Slot the first flag in place and ensure not to stain the paver’s surface with the mixed mortar.
4. Using a rubber mallet, carefully tap the paver to the mortar bed. Once done, ensure the surface is even with a spirit level.
5. Take a measurement of the gap between the pavers
6. Repeat the above steps until all pavers have been perfectly laid
7. Leave the pavers to dry for about 1 to 2 days. You can protect it using a tarpaulin if concerned about rain.
8. Use the jointing compound to fill up the paver gaps to bind together the pavers. Ensure to wipe off any excess compound using the hard-bristled brush.

1. If you’ve not got an overhang or it’s a fixed deck, fit starter clips along the outside edge of the frame and secure with screws provided with the composite decking. If you are working with an overhang, put the first board into position not exceeding 25mm. If you’re adding a fascia, put an off-cut of board under the overhang so you know it’ll be flush with the fascia.
2. Pre-drill all fixing points, measuring in 30mm from the edge of the board. Secure the board to the joist below with composite decking screws.
3. Slide a hidden fastener clip in so it sits within the groove of the deck board. It needs to be in the centre of the joist to keep the boards secure and ensure an expansion gap of 6mm. Tighten the clips until just tight, and repeat so there’s a clip at every joist.
4. Add the next board, ensuring that the fastener clips sit within the groove – make sure you don’t force it. Repeat step 3.
5. Continue steps 3 and 4 until you’re at the final board, which you should secure in the same way as you did the first.

Properly installed wooden decking will not need a lot of maintenance. Most manufacturers recommend regularly brushing leaves and dirt off the deck, and a yearly cleaning and staining procedure. This will keep the wood in the best condition. Fluids and treatments are readily available from all DIY shops and stores.

The most basic fencing starts at about £27 per panel. But if you want something that’s more decorative and better quality, expect to budget £30-£40 per panel.If you choose to get a professional to help you put up your fencing, they’ll probably be able to get your panels at a cheaper rate.

There is a variety of methods available to ensure that your paving drains properly, for example draining into a lawn or soakaway. Correct drainage of paving is a requirement for planning permission. See our guide on planning permission for paving for more information.

When it comes to fence ownership and responsibility, this is often a subject of dispute between neighbours and understandably so. Owning a fence comes with a number of responsibilities such as arranging and paying for the maintenance and more. Therefore, if you’re not yet sure who owns the garden fence, then you’d probably want to have that sorted to make sure your property stays protected at all times. In this post, we’re going to give you an insight into some of the rules guiding fence ownership in order to help you make informed decisions. Let’s take a look!

There’s no rule of thumb on whether you own the fence on the right hand or the left hand side of your property. Therefore, if you’ve heard any “rules that states otherwise, you can fling that out the window because not everyone will own the left hand side to their fence. The first way to determine who owns the garden fence or which side of the fence you’re responsible for is simply by looking. Although this is not guaranteed or a definite way to determine ownership, it can go a long way to give you a good idea. As you would have expected, fences are most likely built on the land that belongs to the boundary’s owner with the further edge of the fence making the actual boundary. As a result, you can determine a fence ownership simply by identifying where the frames are.

Also, you can determine fence ownership using the title deeds for an official and accurate answer. A copy should be given alongside your paperwork which is received when purchasing your house.

• Have a step tread width of 900mm – if you don’t want them that wide, they should be no less than 760mm
• Add a central step riser to stairs wider than 900mm to prevent them buckling
• Add a step depth (the vertical distance between each step) of between 150 and 180mm if building your own riser, so the steps are at a comfortable depth

• Step treads (the actual step themselves)
• Step risers
• Coach screws
• Deck screws
• Saw
• Drill

1. Make sure the ground where you want to put your steps is level and firm. If it’s not, consider laying concrete or paving slabs to provide a secure surface for your steps to sit so they don’t sink.
2. Grab some joist off-cuts and cut them to the same width as your step treads. Attach them to the step risers at the top and bottom using countersunk coach screws.
3. Place the steps against the sub-frame of the deck; if you’ve put slabs down for support, make sure the steps sit in the middle of them. The longest edge of the stair riser should be on the slabs, and the short edge against the deck. Drill pilot holes through the step and sub-frame joist, then screw the step to the sub-frame with more coach screws.
4. After drilling pilot holes, screw the treads into the risers at each end with deck screws.
5. If you don’t want gaps between each stair, you can add joist off-cuts or deck boards. Measure the height and depth of the gap, then screw the off-cut or board into the step riser with two screws at each end.

How To Landscape A Garden

Are you thinking about landscaping your garden? Well, not only will this make your property more visually appealing, but can also go a long way to add value to it. Landscaping a garden can be a very difficult project which should be left to a reliable professional who can guarantee the best results the first time, especially if you lack proper training or experience in the field. This way, you get to save time and extra money that can result due to possible costly mistakes. However, if you’re confident enough about your skills, here’s a step by step guide to help you through the garden landscaping process.

• Start from the front yard. This is the first place you’ll see when you get home and visitors will admire when they stop by.

• Hardscape first. Tackle all the handscaping projects before setting out the plants. The hardscapes include the sidewalk, drive way, porch, decks, fencing and the likes.

• Toil in the soil. When it’s time for the garden, you can start by amending your soil with organic matter before you set out the plants.

• Plan next to your house. When it comes to landscaping a garden, functionality is just as important as the beauty. With that in mind, never allow your foundation planting to cover your house, but to embrace it.

• Selecting the right plants. Study the landscape, observe when the sun rises and sets and determine the best plants for those conditions, you can consult with a local garden centre for more information.

• Plant shapes and textures. You can include some design elements to your landscape simply by taking advantage of the plants’ shape and texture.

• Finishing touches. These includes adding stuffs like containers, window boxes, hanging baskets both to add a little more functionality and a bit more colour to your landscape.

• Maintenance. To enjoy your beautiful landscape for a longer period, it has to be maintained.