Find a Landscaper you can trust in South East.

• Paving slabs – old or cheap ones are fine
• Timber for the frame and legs
• Type 1 MOT hardcore

1. Mark out the area as we explain in ‘How to lay decking’. Then, dig to 200mm below where you want to surface of the decking to be.
2. Add a 50mm layer of hardcore and make sure it’s compact.
3. Build the decking sub-frame as we describe in ‘How to build a deck frame’.
4. Lay out paving slabs along the edges and in the centre of the area. This will help to spread the weight of the decking.
5. Set the decking frame on the slabs, checking for high or low points and adding off-cuts of timber where needed. Don’t forget to sand and seal these off-cuts with decking preservative.
6. Add your joists and then the deck boards, leaving the recommended gaps of expansion of between 5-8mm.

The best way to build a fence depends on what style it is, as different types have different components. However, fencing made up of posts and panels is pretty common. To put this up, you’ll need to start by measuring out and digging holes for your fence posts. Then you’ll need to fit the panels between them and use concrete to secure the posts in the ground.

Try to put your shed in open space, away from trees, bushes and other buildings. This will help to protect it from falling branches and sap. It will also mean that you can access all sides of the shed for repair and maintenance purposes. Make sure you take a look at garden shed planning rules before you pick a final spot for your shed.

Moss, mushrooms and weeds are all problems that many homeowners face on their lawns. Luckily, with a bit of maintenance, there are ways you can get rid of these unwanted organisms and prevent them from coming back. Getting rid of moss A simple way to remove moss from your lawn is by scarification. This basically means that you vigorously rake your lawn, but only do this in the autumn when the grass is actively growing and it’s not too hot, cold or dry. However, you can also use specific weedkillers to control moss on your lawn, and most of these should be applied when the moss is actively growing. Apply in fine weather by hand or with a push-along spreader, making sure not to apply too much as you could kill off the grass too. Check the instructions, as some will require watering after 48 hours if it’s not rained. Then, get into a scarification routine to help prevent moss growth. Removing mushrooms from your lawn If you’ve got mushrooms in your lawn, it usually means that your lawn is damp and shaded, so it never dries out, and is organic waste-rich. There could be a drainage problem with your lawn that is encouraging mushroom growth, so it’s important to investigate why the mushrooms are growing to prevent them from returning once you’ve removed them. To get rid of mushrooms in your lawn, make sure you scarify your lawn and get rid of all the moss, thatch and dead grass that comes up. If you leave it, this is heaven for mushrooms to grow in. If your lawn is shaded, try to prune and thin surrounding trees to offer it more light. If you do all of these things, it will prevent mushrooms from growing in the future, and then it might be worth using a fungicide to get rid of the mushrooms that are there. But if you just do this step, it’s likely the mushrooms will just come back. How to get rid of weeds To get rid of weeds from your lawn, you can use selective weedkillers that will just kill the weeds and leave your grass alone. But if you’d rather not use weedkiller, you can get rid of weeds from your lawn manually. For large, deep-rooted weeds like dandelions or plantains, use a trowel to lever them out, ensuring that you get the whole plant including its roots. Then use compost to fill the hole it leaves behind, pushing it deeply into the hole. Sprinkle with fresh grass seed, cover with extra compost and water. Make sure you keep the area damp until the seed has germinated. To prevent moss, mushrooms or weeds from returning, the best things to do are:

• Scarify your lawn in the autumn, and lightly in the spring if necessary
• Seed your lawn in the autumn if you need to
• Try to keep trees trimmed and pruned as much as possible to reduce shade
• Use a pre-emergent weedkiller in the spring to catch them before they grow and handpick any that come through
• Mow your lawn regularly in the spring and summer, being careful not to remove more than a third of grass at a time, then before winter give it one last mow and a fertilisation treatment

With summer comes a lot of lawn challenges - from sod webworms, chinch bugs, nutsedge to drought stress, diseases and lots more. A lot of people find it hard to tell what’s happening to their lawn and probably assume it to be as a result of the summer stress and will definitely turn green again once the fall rolls in. This may be right in certain situations, but if you have fungi eating deep into your lawn, the green may not return. So, how exactly do you figure out if your lawn has diseases or pests? In this post, we’re going to provide you with a good insight into this to help you take the necessary treatment steps as soon as possible.

• Fungal structures. Fungi structures are not usually the easiest to spot as they vary in shape, colour and appearance. Fortunately, most fungi that appears on lawns will possess some type of structure which can be spotted when moisture is present. Once the night time dew sets in, you’ll be able to identify these strange growths in your lawn.
• Matted or Collapsed Areas. There is some sort of diseases that will make grass plant to wilt in little time. This, combined with fungi structures will make the grass look to have been matted in some areas.
• Discoloured or oily areas. Some areas are likely to show symptoms more than the others. While the unaffected turf may remain in its normal state, areas that are nearby may vary in colour due to the damage to the leaf tissue.
• Lesions or spots on leaves. Do you notice a certain damage pattern on the leaf blades of the grass plants? If yes, then your lawn is probably infected with a disease. Some of these spots may vary in size and colour.

Most responsible contractors will dispose of the old fencing via an approved commercial waste site. Do check that the cost of taking rubbish away is included in the quotes you receive, otherwise you might find you get stung when it comes to paying for the work.

1. If you’ve not got an overhang or it’s a fixed deck, fit starter clips along the outside edge of the frame and secure with screws provided with the composite decking. If you are working with an overhang, put the first board into position not exceeding 25mm. If you’re adding a fascia, put an off-cut of board under the overhang so you know it’ll be flush with the fascia.
2. Pre-drill all fixing points, measuring in 30mm from the edge of the board. Secure the board to the joist below with composite decking screws.
3. Slide a hidden fastener clip in so it sits within the groove of the deck board. It needs to be in the centre of the joist to keep the boards secure and ensure an expansion gap of 6mm. Tighten the clips until just tight, and repeat so there’s a clip at every joist.
4. Add the next board, ensuring that the fastener clips sit within the groove – make sure you don’t force it. Repeat step 3.
5. Continue steps 3 and 4 until you’re at the final board, which you should secure in the same way as you did the first.

1. Plan your shed base You must have a sturdy base for your shed, otherwise the frame won’t stand properly and could stop the door from opening. Decide whether you’re going to have:
   • A concrete base laid on hardcore
   • Concrete slabs on sharp sand
   • Treated wood beams on hardcore or shingle
   • An interlocking plastic system
   All bases should be laid on firm, level ground as far as possible.
2. Treat wood with preservative To help your shed last as long as possible, you should coat all the wooden parts with timber preservative before you put it together.
3. Put the shed floor together Some will need more assembly than others, but you need to make sure that the floor panel is attached to the joists; follow the manufacturer’s instructions for the correct spacing.
4. Put up the shed walls
   • Mark the centre point of each wall on its bottom edge, then do the same for the shed floor so you can line them up together.
   • Stand the gable end on the base and line it up. Check that it’s vertical with a spirit level – you might need someone to support the panel while you do this. Use a temporary holding batten to keep it in place.
   • Fix a side panel to the gable end panel with countersunk screws, then add the second side panel in the same way.
   Don’t attach the panels to the floor until you’ve fitted your shed roof.
5. Fit the roof
   • If the shed comes with a support bar, put this in position before you put the roof panels in.
   • Nail the roof panels in place, ensuring there’s a parallel and equal overlap at each end.
   • Roll out some roofing felt from front to back, leaving a 50mm overlap at each side. Secure it with clout-headed felt tacks at 100mm intervals.
   • Apply mastic sealant to the outside corners, then fix each corner trim with 30mm nails.
   • Add the fascias and finials, predrilling 2mm holes to avoid splitting the wood. Nail them through the felt into the shed using 40mm nails.
6. Add the shed windows
   • Slide each windowsill into the tongue and groove cut out, then put the window cover strip in position, fixing it to the vertical framing.
   • From inside the shed, put the glazing sheets into the window rebates, making sure the bottom edge of the glazing sheets sit on the outside of the sill.
   • Fix the window beading on the top and sides with 25mm nails.
7. Fix the walls to the floor Before you do anything, make sure you check that the centre marks on the walls line up with the marks on the shed floor. Then fix the wall panels to the floor with 50mm screws, aligning them with the joists.
And that’s it! But if you’re not confident in building a shed yourself, there are plenty of professionals available who will be happy to help.