Find a Landscaper you can trust in Ryton.

• Paving slabs – old or cheap ones are fine
• Timber for the frame and legs
• Type 1 MOT hardcore

1. Mark out the area as we explain in ‘How to lay decking’. Then, dig to 200mm below where you want to surface of the decking to be.
2. Add a 50mm layer of hardcore and make sure it’s compact.
3. Build the decking sub-frame as we describe in ‘How to build a deck frame’.
4. Lay out paving slabs along the edges and in the centre of the area. This will help to spread the weight of the decking.
5. Set the decking frame on the slabs, checking for high or low points and adding off-cuts of timber where needed. Don’t forget to sand and seal these off-cuts with decking preservative.
6. Add your joists and then the deck boards, leaving the recommended gaps of expansion of between 5-8mm.

1. Start in one corner of the sub-frame and position the first board across the inner joists. You want the deck board in the opposite direction to the inner joists, ensuring that it’s flush with the frame. Position any end-to-end joins between the deck boards halfway across an inner joist so you can screw both boards into the joist for stability. Make sure you keep a gap of between 5-8mm to allow for expansion of the wood.
2. Begin to screw your deck boards to the joists. You’ll need to secure the deck board to every joist is covers along your deck frame. Use two screws for every joist. Mark where you’re going to add your screws, ensuring that they are at least 15mm from the end of the board and 20mm from the outside edges. Drill pilot holes for the screws, being careful to only drill through the deck board and not the joist. Then screw the decking screws into the holes.
3. Continue to screw in the deck boards, ensuring you leave the correct expansion gap. You can stagger the deck board joins across the deck for more strength.
4. Sand down any cut ends if you need to before applying decking preserver to protect the timber from rotting.

What Is Landscape Gardening?

Landscape gardening is basically the art of setting out grounds or planting of ornamental plants so that a picturesque effect is created. In other words, it can be seen as the beautification or decoration of a portion of land to generate a naturalistic effect in a limited space. However, it should also be noted that landscape gardening meant to beautify places, but also important and very functional as our surroundings make a whole lot of contribution to the quality of our lives. Landscape is a word that’s not only used to qualify an beautiful scenery, but also stands for a great historical records of natural features created by human activities over time. So what are the general principles of landscaping?

• The right landscape garden should express some thought or feeling, just like a good landscape painting. The expression can be bold, quiet, retired and more.

• The landscape garden area should be divided into various sections with a plan for each individual area. The whole plan should be actualized in such a way that an observer or visitor can imagine the entire plan and purpose without having to analyse each parts.

• It’s of great importance to combine both beauty and utility effectively.

• The design’s simplicity should be emphasized while executing the plan.

• The garden and building should perfect blend with each other in such a way that they could be seen as one rather than the landscape garden stopping abruptly in front of the building. The view of the garden from the building’s door or window should offer an breath taking scenery. In short, every part of the landscape should be planned so that every visitor will have a surprising effect when seen.

• The ideal landscape should not be too tight and should possess an open space.

• Do not overcrowd the plants and objects.

1. If you’ve not got an overhang or it’s a fixed deck, fit starter clips along the outside edge of the frame and secure with screws provided with the composite decking. If you are working with an overhang, put the first board into position not exceeding 25mm. If you’re adding a fascia, put an off-cut of board under the overhang so you know it’ll be flush with the fascia.
2. Pre-drill all fixing points, measuring in 30mm from the edge of the board. Secure the board to the joist below with composite decking screws.
3. Slide a hidden fastener clip in so it sits within the groove of the deck board. It needs to be in the centre of the joist to keep the boards secure and ensure an expansion gap of 6mm. Tighten the clips until just tight, and repeat so there’s a clip at every joist.
4. Add the next board, ensuring that the fastener clips sit within the groove – make sure you don’t force it. Repeat step 3.
5. Continue steps 3 and 4 until you’re at the final board, which you should secure in the same way as you did the first.

Pitting, also referred to as spalling is the event whereby “pits” or small holes start showing on the surface of your concrete driveway which makes it appear both worn and uneven. Concrete driveway pitting is a common but highly frustrating problem for most homeowners. You’ll see some concrete driveways that’ll only start to pit after a couple of years, but this is not true for all concrete driveways as others will start to show signs only after a couple of months. So how do you tackle this issue? Well, it’s relatively simple to tackle, however if you’re not confident or lack the necessary skills, we’d recommend you get in touch with a reliable professional who can guarantee the best results for help. In this guide, we’ll take you through the concrete driveway pitting repair process.

✓ Prepare the pits by cleaning the area, clearing out all debris and more. The small pits can be cleaned with a stiff brush while a sturdy broom will do a good job for larger pits.

✓ Make use of a hose to spray the concrete pits and flush out all remaining bits of waste.

✓ If you’re tackling series of small pits, simply use a caulking gun filled with pre-mixed epoxy and specially formulated for concrete to fill the pits. Clear off the excess eproxy ensuring that its level with the concrete surface. Once done, simply leave for at least 24 hours before the application of a concrete sealant to prevent the wear and tear of the new concrete.

✓ Chisel out a little concrete and clean with a pressure washer. Once done, apply a concrete resurfacing compound mixture into the holes and use a trowel to level off.

✓ Ensure that the repaired concrete driveway is protected from rain and foot traffic for at least 6 hours (or 24 hours for vehicles).

How To Landscape A Garden

Are you thinking about landscaping your garden? Well, not only will this make your property more visually appealing, but can also go a long way to add value to it. Landscaping a garden can be a very difficult project which should be left to a reliable professional who can guarantee the best results the first time, especially if you lack proper training or experience in the field. This way, you get to save time and extra money that can result due to possible costly mistakes. However, if you’re confident enough about your skills, here’s a step by step guide to help you through the garden landscaping process.

• Start from the front yard. This is the first place you’ll see when you get home and visitors will admire when they stop by.

• Hardscape first. Tackle all the handscaping projects before setting out the plants. The hardscapes include the sidewalk, drive way, porch, decks, fencing and the likes.

• Toil in the soil. When it’s time for the garden, you can start by amending your soil with organic matter before you set out the plants.

• Plan next to your house. When it comes to landscaping a garden, functionality is just as important as the beauty. With that in mind, never allow your foundation planting to cover your house, but to embrace it.

• Selecting the right plants. Study the landscape, observe when the sun rises and sets and determine the best plants for those conditions, you can consult with a local garden centre for more information.

• Plant shapes and textures. You can include some design elements to your landscape simply by taking advantage of the plants’ shape and texture.

• Finishing touches. These includes adding stuffs like containers, window boxes, hanging baskets both to add a little more functionality and a bit more colour to your landscape.

• Maintenance. To enjoy your beautiful landscape for a longer period, it has to be maintained.

This will depend on the size of the garden and the amount of plants within it. For small gardens, fortnightly or monthly visits by a professional gardener will generally be sufficient. For larger gardens or gardens with a lot of plants, weekly visits are best. Some larger projects such as hedge cutting or tree felling may need additional one off visits.

The best way to build a fence depends on what style it is, as different types have different components. However, fencing made up of posts and panels is pretty common. To put this up, you’ll need to start by measuring out and digging holes for your fence posts. Then you’ll need to fit the panels between them and use concrete to secure the posts in the ground.