Find a Driveway Installer you can trust in Lisburn.

A patio is an outdoor space which can be used for a variety of stuffs which includes fun time with family and friends, reading time or just relaxing as the fresh breeze blows. With all these benefits and more, it’s becomes more obvious that there’s a need to keep your patio in a tip top condition at all times. If otherwise, you may not be able to enjoy your patio to your satisfaction and probably, for as long as you would want. You simply have to provide it with a regular maintenance which involves inspecting and identifying the damages that needs to be repaired before it gets out of hand. Fortunately, the minor repairs can be done by yourself if you’re confident enough. However, for bigger damages it’s advisable to call in a professional for help. In this article, we’ll take you through the patio reparation process.

✓ Prepare the area. This involves removing the problem piece gently and carefully. If there’s a piece you think can still be useful, store it in the re-use pile or you can start a new one. Once you’re done removing the pieces, the next thing to do would be to start removing anything that’s unwanted from the damaged area like debris, unwanted soil etc, and start sand fitting with some fresh sand. This should be levelled out to ensure there’s no bumps.

✓ With the sand down, you can start by putting the pieces back in together. This should be done gently to avoid any further damage. Do this until your patio

✓

Resin bound driveways are known to last a long time without the need for repairs, but sometimes accidents happen. You also need to make sure you regularly maintain your driveway by sweeping and power washing it to prevent damage. But if it does get damaged, how do you repair your resin bound driveway?

If you notice a crack in your resin bound driveway, it’s important to repair it as soon as possible. If you leave it to erode, you could end up with a difficult repair that will cost much more money.

To repair a crack, you’ll need to carefully chisel it open slightly so you can apply a primer then fill in the crack with a matching-coloured resin and aggregate mix. While there are variations in colour and size with all stone mixes, usually it’s easy to find a batch that matches almost perfectly. And once the crack has been repaired for a while, it will blend in seamlessly with the rest of your driveway.

To prevent cracking in your resin bound driveway, it’s best to tackle the issue at initial installation. Speak to your installer about whether it’s possible to add fibreglass mesh to the base. You should also ask your installer to add expansion trims as these will significantly reduce the risks of cracks.

So the best way to repair resin bound driveways is to prise open the crack and fill it in. It might seem simple, but getting the right colour match is something that should be left to the professionals, so get a few quotes to ensure you get the best finish.

There’s no doubt that weeds coming through your block paving can be unsightly and annoying. But, it’s relatively easy to get rid of weeds that are growing in the joints between your block paving. To start, pull out the larger weeds, and then you can use a pressure washer or firm bristled brush to remove the smaller weeds and debris from the joints in your block paving. It’s best to then refill the joints with additional sand to ensure your block paving remains level. Regularly brushing your block paving and treating with weed killer will help to prevent the weeds from reoccurring.

To inexperienced people laying of paving slab isn’t much more than digging a little, purchasing little amount of mortar and pressing down the paving slabs. But how good would it have been if only it were that easy in real life? The truth is, in reality, laying paving slabs does not only require you to prepare your sub-base painstakingly and mix your mortar using the appropriate materials, but you’d also have to work with accurate and precise paver placements to guarantee the patio’s longevity. As a result, if you lack proper training or experience, we’d recommend you hire the services of a seasoned professional who can guarantee the best results and also save you time and extra cash that may result from possible costly errors. In this guide, you’d gain more insight into the paving slabs laying process.

To get started, you’ll need sharp sand, cement, shovel, wheelbarrow, pointing trowel, rubber mallet, spirit level, jointing compound, hard-bristled brush and tarpaulin.

• Mix a layer of mortar for each paver.

• Apply the mixed mortar onto the sub base by using the trowel.

• Slot the first flag in place and ensure not to stain the paver’s surface with the mixed mortar.

• Using a rubber mallet, carefully tap the paver to the mortar bed. Once done, ensure the surface is even with a spirit level.

• Take a measurement of the gap between the pavers

• Repeat the above steps until all pavers have been perfectly laid

• Leave the pavers to dry for about 1 to 2 days. You can protect it using a tarpaulin if concerned about rain.

• Use the jointing compound to fill up the paver gaps to bind together the pavers. Ensure to wipe off any excess compound using the hard bristled brush.

If you’re considering laying gravel on your driveway, then you’d probably want to know the amount of gravel you’ll need to complete the project. When you are calculating the amount of gravel you’ll require to cover your driveway, there’s an important factor you’ll need to consider and that is the type of gravel you opt for such as a crushed or pea gravel. There are varying grades which are found in particles from fine to course, with a size ranging from 2mm to 64mm. Therefore, there’s a need to estimate the volume of the gravel while also having the rock’s size in mind. Also, there’s a need to select your most preferred gravel which you’ll like to use before proceeding to dig the depth of your driveway and subsequently determine the amount of gravel that’ll be needed using these excellent tips.

✓ Determine the size and coverage. As you would have expected, the smaller the gravel is, the bigger the coverage will be, and gravels should be at least 4 inches deep. However, if the rocks happen to be a bit large then you can allow for an extra 1/2 inch.

✓ Measure the driveway. Multiply the width by the length and depth to get the size of the driveway in cubic feet. Meanwhile for cubic yards, you can divide the total cubic feet by 27. This is due to the fact that one cubic feet is same as 1.13 tons.

✓ Working with gravel. Here, you’ll have to calculate an underlay measurements differently. You can use 2 inches of road base that’ll be overlaid with 2 inches of gravel.

Some paving projects require you to cut paving slabs to make them fit into a smaller space. To do this, firstly you need to measure the slab and draw a line in pencil or chalk where you want to cut.

There are then several different ways you can cut the slab – you or your professional can choose the one you or they are most happy with. A hammer and chisel can work well, or a handheld saw. You can also use an angle grinder fitted with a stone-cutting disc.