Find a Driveway Installer you can trust in Askam-in-furness.

There are several effective ways to clean paving slabs. It’s important to pick a method that suits you and your paving material.

Whatever method you use, start by removing all weeds and loose debris from your paving. Then, if you have a pressure washer, you can simply use this to clean away any dirt.

If you don’t have a pressure washer, you can try using soapy water or watered-down bleach. If you use soapy water, mix a mild detergent like washing up liquid with warm water. Then pour it onto your paving, work it in with a brush and rinse it off with clean water.

If you use bleach, first make sure that the water won’t drain off onto any plant life, as this can kill it. You should also avoid using bleach on concrete slabs, as it will cause them to fade. Mix one-part bleach with five-parts water, pour it onto your paving and work it in with a brush. Then leave it for 15 minutes and rinse it off with clean water.

Tarmac is a material made up of broken stone and tar, used for surfacing roads, driveways and other outdoor areas. It’s actually a registered product trademark, but many people use ‘tarmac’ interchangeably with ‘asphalt’. Asphalt is similar to tarmac, but is now more commonly used, and is made from bitumen instead of tar.

While many professionals will recommend a pressure washer to clean block paving, it’s possible to clean your paving without one – just scrub the affected areas with a firm bristled brush and use plenty of soap. Then, rinse off the area with clean water.

How To Repair A Pothole In Gravel Driveways

When the integrity of your gravel driveway is impaired not only does it have a negative impact on the curb appeal of your property, but also makes your driveway a danger zone. If your driveway needs to be repaired, you’d simply have to grab the bull by the horn and get it done - the sooner, the better to avoid the problem getting worse and to have your beautiful gravel driveway back as soon as possible.

The major cause of potholes in driveways is usually water, when it gets trapped beneath the surface of the driveway. Therefore, you may also want to enhance the drainage in the area as part of your repair. The repair process is quite simple for confident do-it-yourselfers, but if otherwise, then calling in a reliable professional will save you some time and extra money that can result from possible errors. So how do you repair gravel driveway potholes?

✓ Prepare the area. This involves removing all forms of debris from the pothole. To achieve this, you can rake, shovel or brush the loose stones, soil and other debris from the pothole.

✓ Fill the pot hole. Make use of a coarse gravel to fill up the pothole to a depth of about 3 inches beneath the driveway’s level. Upon the filling, simply tamp down the coarse gravel using a commercial tamper or any available homemade option. Once done, the final 3 inches to the surface of the gravel driveway should then be filled up with gravel which perfectly matches the colour and texture of the remaining driveway.

✓ Compact the patch. To achieve this in an easy and fast way, simply run your car’s wheel up and down over the repaired spot gently a couple of times. This will be enough to compact the patch and seal the pothole.

How to joint pave or grout paving slabs is a common question asked by several home owners. Most times they may have some existing paving and thinking its high time to have them re-pointed or laid some new pavings and wondering how to fill the gaps.

In the UK, patios don’t get much use especially during cold winter months. However even when not in use, the combination of wet weather and cold temperatures is capable of having the hardest outdoor living spaces looking a bit neglected. This may lead to cracked grouting which leaves gaps between stones making way to a place where weeds can grow and flourish during spring. You definitely wouldn’t want your outdoor living space looking this messy. Hence, there’s a need to get your patio back on track by grouting the paving slabs. However, if you lack proper training or experience, it’s advisable to employ a reliable professional who can guarantee the best results. In this guide, you’ll learn more about the paving slabs grouting process.

• Saturate the area that needs to be repointed with the help of a hosepipe and/or watering cans. Use a yard brush to distribute the water across the paving slabs.

• Pour a generous amount of your compound product over the newly soaked patio.

• Sweep the into the joints where it’s needed with the help of a broom. Do this carefully in order to make sure each and every joint is fully filled with the compound. If done right, this can help prevent premature cracking for a long period of time.

• Once the joints are filled with the compound, brush aside the exces product and strike it in. Ensure that the product is pressed firmly into each gap leaving behind no spaces.

• Sweep out the excesses which can be kept for future use.

1. Prepare the sub-baseThe driveway company will excavate, or dig, the existing surface down to a depth of around 200mm. They will remove any debris from the area may place it in a skip or arrange for it to be removed in another way. When they dig down to the sub-base of your previous driveway, they will assess how much hardcore they need and arrange for that to be delivered to the site. They will then spread the hardcore across the sub-base to create a level surface to pour the concrete on. Most good contractors will apply a gel to any walls and doors to protect them from concrete splashes. They will also add any gulley tops, manhole covers or shuttering that’s required.
2. Installation and imprintingNext, the tradespeople will have the concrete either poured from a large mixer vehicle or barrow it in from a mixer and pour onto the surface. They level it with rakes, then add a colour surface hardener in a colour of your choice. This will give the driveway its permanent colour. They will then wait until the concrete has hardened to the correct consistency for imprinting the pattern, then will use special tools and stencils to make the pattern that you asked for. They will then spread a colour powder called a release agent over the surface, and leave to dry for 1 to 2 days depending on the weather conditions.
3. CleaningWhen the contractors return, they will add crack control cuts into the concrete. This is important because concrete expands and contracts in the heat, so there needs to be some give to stop any larger cracks from forming. Then everything is power washed clean, and a chemical wash is also used on the concrete to ensure it’s completely dust-free. The installers will ensure all your walls and doors are clean, which will hopefully be an easy job if they used wall gel.
4. SealingThe final step is to seal the driveway. There needs to have been at least two dry days before the tradespeople can do it, so you might find it’s best to have your pattern imprinted driveway installed in the summer. The contractors will blow any debris away from the surface and dry any damp areas where necessary. They will then add an anti-slip agent to the sealant and brush it on. It’s best to not walk or drive onto your new concrete driveway for about 4 days after sealing to allow everything to set. But after that, you’re ready to use your new driveway!

The most commonly used driveway surfacing materials are gravel, asphalt, concrete and paving - which can be block, slabbed or patten imprinted. Take a look at our product information pages to help you decide which one to use and which one will look best for your driveway.