Find a Driveway Installer you can trust in Workington.

Patios do not require lots of maintenance. They will only need occasional cleaning to make sure that the material keeps its original appearance. It's always best to clean your patio with a pressure washer and occasionally tap each slab or brick just to check the sand underneath hasn't washed away.

1. Prepare the sub-baseThe driveway company will excavate, or dig, the existing surface down to a depth of around 200mm. They will remove any debris from the area may place it in a skip or arrange for it to be removed in another way. When they dig down to the sub-base of your previous driveway, they will assess how much hardcore they need and arrange for that to be delivered to the site. They will then spread the hardcore across the sub-base to create a level surface to pour the concrete on. Most good contractors will apply a gel to any walls and doors to protect them from concrete splashes. They will also add any gulley tops, manhole covers or shuttering that’s required.
2. Installation and imprintingNext, the tradespeople will have the concrete either poured from a large mixer vehicle or barrow it in from a mixer and pour onto the surface. They level it with rakes, then add a colour surface hardener in a colour of your choice. This will give the driveway its permanent colour. They will then wait until the concrete has hardened to the correct consistency for imprinting the pattern, then will use special tools and stencils to make the pattern that you asked for. They will then spread a colour powder called a release agent over the surface, and leave to dry for 1 to 2 days depending on the weather conditions.
3. CleaningWhen the contractors return, they will add crack control cuts into the concrete. This is important because concrete expands and contracts in the heat, so there needs to be some give to stop any larger cracks from forming. Then everything is power washed clean, and a chemical wash is also used on the concrete to ensure it’s completely dust-free. The installers will ensure all your walls and doors are clean, which will hopefully be an easy job if they used wall gel.
4. SealingThe final step is to seal the driveway. There needs to have been at least two dry days before the tradespeople can do it, so you might find it’s best to have your pattern imprinted driveway installed in the summer. The contractors will blow any debris away from the surface and dry any damp areas where necessary. They will then add an anti-slip agent to the sealant and brush it on. It’s best to not walk or drive onto your new concrete driveway for about 4 days after sealing to allow everything to set. But after that, you’re ready to use your new driveway!

The short and also easy answer to this inquiry is yes, Indian stone paving is absolutely a perfect choice for not just driveways yet likewise for producing a brand-new garden path, patio and also the likes. Considering that its introduction to the market almost 3 years ago, home and also homeowner have located their brand-new driveway surfacing choice in Indian sandstone rather than the much more conventional products. Every homeowner has an one-of-a-kind feature they desire in their driveways, nonetheless the suitable driveway for all would certainly be very durable as well as durable, visually appealing while likewise being very inexpensive. Fortunately, the Indian stone| driveway comes out on top in every department, making it the ideal selection for all home and property owners. In this article, we're mosting likely to think about some reasons an Indian stone driveway just can not be disregarded. Let's take a look!

• It's very long enduring and resilient. The Indian stone driveway has a much of quartz which makes it long lasting as well as resistant to discolouration and extreme weather condition. It has the ability to endure all type of stress which is particularly helpful driveways which will continued to be tested in a lot of means throughout its lifespan.
• Low upkeep. The Indian stone driveway is really easy to clean as well as keep as the majority of dirt collected in time will be removed by water and the remaining ones can quickly be hosed sown. To put it simply, you can merely install this paving and forget about it as it'll mainly care for itself.
• Visually appealing. The Indian sandstone is very eye-catching and also it'll not fade or discolour. It likewise includes a variety of refined colours and varying patterns, so you 'd obtain a myriad of choices to pick from.

You should pull up and remove weeds by hand as and when they appear. If it is a regular problem, you might need to reseal the paving. In extreme cases, the sub layer itself may need to be re-laid. You can use weed killer, however some paving can be discoloured by stronger weed killers.

If you’re considering getting a new tarmac driveway or outside area, it’s important to know how long it takes to dry. Try to use it too early and you might damage it and ruin its appearance.

It won’t be long before you can walk on your new surface, as long as you’re careful. However, it’s a good idea to avoid putting heavy objects or driving on it for 2-3 days. For a more accurate timescale, ask your tarmac paving and driveway pro.

The most commonly used driveway surfacing materials are gravel, asphalt, concrete and paving - which can be block, slabbed or patten imprinted. Take a look at our product information pages to help you decide which one to use and which one will look best for your driveway.

Have you decided to install block paving and wondering what the best sand to be applied to the joints is in order to achieve a perfect job? Well, you’re at the right place! This is one of the most frequently asked questions when it comes to block paving and we seek to give you a reliable solution once and for all.

The best sand for block paving is a kiln-dried sand. It’s an extremely fine sand which has been dried in a kiln to get rid of all the water before it’s incorporated to achieve the best results. Therefore, the sand contains no moisture and is commonly used to fill the joints of block paving to keep the paving’s structure rigid and strong. It also goes a long way to prevent the ingress of water while stopping the paving from moving and becoming loose. The major reason why the paving sand must be dried is to allow it flow easily into the joints as well as the block paving’s gaps. As result of this smooth flowing to the bottom of the joints, there will be no sand sticking to the sides of the pavers.

Another major reason why kiln-dried sand is commonly applied to the block paving’s joints is to prevent water from penetrating the paved area. It also tightens the individual pavers together to prevent from moving and becoming loose. In the event whereby you happen to leave the joints of your block paving without kiln dried sand, it’s highly likely that they’ll sink as a result of water penetration and the blocks will become very loose. After washing block paving, it’s very important to also replace any sand washed off in the process once the paving is dried to prevent water ingress into the joints.