Find a Driveway Installer you can trust in Maldon.

If you’re considering laying gravel on your driveway, then you’d probably want to know the amount of gravel you’ll need to complete the project. When you are calculating the amount of gravel you’ll require to cover your driveway, there’s an important factor you’ll need to consider and that is the type of gravel you opt for such as a crushed or pea gravel. There are varying grades which are found in particles from fine to course, with a size ranging from 2mm to 64mm. Therefore, there’s a need to estimate the volume of the gravel while also having the rock’s size in mind. Also, there’s a need to select your most preferred gravel which you’ll like to use before proceeding to dig the depth of your driveway and subsequently determine the amount of gravel that’ll be needed using these excellent tips.

✓ Determine the size and coverage. As you would have expected, the smaller the gravel is, the bigger the coverage will be, and gravels should be at least 4 inches deep. However, if the rocks happen to be a bit large then you can allow for an extra 1/2 inch.

✓ Measure the driveway. Multiply the width by the length and depth to get the size of the driveway in cubic feet. Meanwhile for cubic yards, you can divide the total cubic feet by 27. This is due to the fact that one cubic feet is same as 1.13 tons.

✓ Working with gravel. Here, you’ll have to calculate an underlay measurements differently. You can use 2 inches of road base that’ll be overlaid with 2 inches of gravel.

No, pattern imprinted concrete shouldn’t be slippery. Most good driveway installers will add a special anti-slip agent to the sealant before they brush it onto your driveway, so it will stop it from being slippery.

It’s important to ask a driveway company how they will seal your driveway when you get a quote from them. If an untrustworthy company seals your driveway badly, it can cause a thick and extremely slippery surface, so it’s vital that you ask any contractor what their procedure is before you engage them.

It’s also important to remember that pattern imprinted concrete isn’t a ‘non-slip’ surface – it’s just not slippery. You could still slip over on a concrete driveway, just like you could on tarmac or a block paved driveway. Also, once you’ve walked and driven over your driveway for a few months, its skid and slip resistance will increase as it weathers and builds up tiny specs of dirt on it. Pattern imprinted concrete is often used in high footfall areas in places like shops, fast food restaurants and theme parks, so if there was a significant slip risk these businesses wouldn’t use it.

You might think that you could ask your contractor not to seal the driveway to make it less slippery, but it could actually do the opposite. By sealing pattern imprinted concrete, it means that moss and algae is much less likely to grow, which can be extremely slippery to walk on if it’s left to its own devices. If moss does form on your driveway, the sealed surface is much easier to clean as you can simply pressure wash it away; this is not as easy to do on a non-sealed surface.

• Where you live
• How big you want your driveway to be
• What colour or design you would like
• Whether any additional work will need to be completed to prepare the area for the driveway

If you want your tarmac driveway or outdoor area to last as long as possible, it’s important to look after it. This means giving it a good clean every so often.

If there are any greasy or oily stains on your tarmac, you won’t get these off only using water. Get a degreaser and follow the instructions. You’ll then need to use a pressure washer or hose to rinse off the detergent and clean the rest of your tarmac or asphalt area.

Avoid getting your pressure washer too close to your outdoor surface or pointing it directly at it. You should also avoid cleaning the same area for too long. This will help you clean your tarmac while avoiding damaging it.

Do you want to install a new patio? If yes, then on top of the agenda will definitely be the cost of paving slabs. However providing a single and accurate estimate to the cost of your new patio is almost impossible as there are many factors that can influence what the price would be. These factors include the size of the area, the choice of stone, installations and lots more.

To get a more accurate estimate of your cost there’s is the need to look at some factors before calculation. These includes envisioning your patio as well as putting the drainage in mind. Firstly, you’ll need to decide where you want your patio to be - this should include considering whether you’ll get enough privacy sitting on your patio and more. If you’re able to identify where to put your patio, you’ll be able to have a clearer idea of the potential shape and size of the patio. Secondly, there’s a need to consider the drainage because failure to provide adequate drainage will only result in storing of water which leads to a development of algae or vegetation across your patio.

The material you opt for is also a huge determinant of your patio’s cost. When it comes to paving slabs you’ll only get what you pay for. Deciding to go for cheaper paving slabs will most likely lead to frequent staining, slippery surface, tough maintenance as well as constant cracking. Consequently, the act of cutting back on the cost of paving slabs will only you cost you more money in the long run. What’s more? If you have an existing patio you’d like to replace, then you’d probably need to include the cost of removing the existing one.

Creating a tarmac path or driveway is a tricky process. It’s a job best left to professionals who know what they’re doing, as there are plenty of opportunities for it go wrong. However, even if you’re planning to hire someone to do it for you, it’s worth knowing how it’s done.

Firstly, you’ll need to remove any existing path or driveway and excavate down to formation level – about 175mm below paving level. Then, a membrane is laid down to prevent weed growth.

Next, a sub-base goes down, usually made of crushed rock or concrete. This is compacted and the tarmac is laid over the top. This is put down in two layers, and is rolled to make it compact and smooth.

It’s important to use edging when laying tarmac, to ensure that it doesn’t run off where you want your path or driveway to be. Tarmac paving and driveways also needs suitable drainage.

The most commonly used driveway surfacing materials are gravel, asphalt, concrete and paving - which can be block, slabbed or patten imprinted. Take a look at our product information pages to help you decide which one to use and which one will look best for your driveway.

Oil stains on your concrete driveway can look obvious and unsightly. However, there are several different ways to remove them.

If you’ve only just spilled the oil, you can use a mixture of absorbent material, like sawdust, and solvent, like acetone or lacquer. Combine these, place them on the stain, cover and leave for about 24 hours. Then sweep up the mixture and rinse the area with water.

If you’ve got a small, older stain, you can use a detergent like baking soda, vinegar, washing up liquid or laundry detergent. Cover the stain with the detergent and leave for about 30 minutes. Then, add hot water and scrub the area and rinse. You might need to repeat this if necessary.

If it’s a larger, more stubborn stain, you might need to use a special degreaser. You can use this similarly to a detergent but make sure you follow the instruction on the bottle carefully.