Find a Driveway Installer you can trust in Garndolbenmaen.

When your driveway is suffering from depression, it becomes unsafe for driving (a danger zone) and ugly - no homeowner wants that! Unfortunately, most driveways won’t hold flat for long as they tend to develop cracks and potholes pretty quickly. Here, we are going to take you through how to fill asphalt driveways’ depression so as to ensure the sinkholes in your driveway poses no threat to you or your loved ones, while also beautifying your property. The approach to be used depends on the intensity of the depression. If its only a few cracks and holes, this can easily be repaired with some equipment. But if otherwise is the case, then calling a reliable professional will be your best bet. In this article, we’ll show you how to repair dips in your asphalt driveway relatively quickly.

✓ Pick a date with warm and sunny weather. This is because if you work in a cold weather, chances are the materials will freeze and hence, unusable. So find a day when the temperature will over 50 degrees Fahrenheit and below 80 degrees Celsius and when there would be no rain. We’ll advise a day between May to October.

✓ Prepare the area. Remove all loose stones, soil, dirt as well as vegetation from the holes. Once done, you can then proceed to washing the area with a pressure washer or sweep with a broom.

✓ Apply a thin mixture of asphalt to the area. Use a flat stirring stick to coat the low driveway area with a thin mixture of asphalt.

✓ Tamp the asphalt repair mix. Purchase the right kind of asphalt to repair the driveway. Fine aggregate asphalt mixture is more suited to filling small holes, whereas the coarse aggregate is more suited to filling larger holes. Apply layers ( about 2 inches each time) of the asphalt repair mix to the sunken area and use a shovel to give it a smooth finish. Once done, simply make the area smooth and protect it with a piece of plywood. Do not walk or drive on the area for a couple of days.

1. Prepare the sub-baseThe driveway company will excavate, or dig, the existing surface down to a depth of around 200mm. They will remove any debris from the area may place it in a skip or arrange for it to be removed in another way. When they dig down to the sub-base of your previous driveway, they will assess how much hardcore they need and arrange for that to be delivered to the site. They will then spread the hardcore across the sub-base to create a level surface to pour the concrete on. Most good contractors will apply a gel to any walls and doors to protect them from concrete splashes. They will also add any gulley tops, manhole covers or shuttering that’s required.
2. Installation and imprintingNext, the tradespeople will have the concrete either poured from a large mixer vehicle or barrow it in from a mixer and pour onto the surface. They level it with rakes, then add a colour surface hardener in a colour of your choice. This will give the driveway its permanent colour. They will then wait until the concrete has hardened to the correct consistency for imprinting the pattern, then will use special tools and stencils to make the pattern that you asked for. They will then spread a colour powder called a release agent over the surface, and leave to dry for 1 to 2 days depending on the weather conditions.
3. CleaningWhen the contractors return, they will add crack control cuts into the concrete. This is important because concrete expands and contracts in the heat, so there needs to be some give to stop any larger cracks from forming. Then everything is power washed clean, and a chemical wash is also used on the concrete to ensure it’s completely dust-free. The installers will ensure all your walls and doors are clean, which will hopefully be an easy job if they used wall gel.
4. SealingThe final step is to seal the driveway. There needs to have been at least two dry days before the tradespeople can do it, so you might find it’s best to have your pattern imprinted driveway installed in the summer. The contractors will blow any debris away from the surface and dry any damp areas where necessary. They will then add an anti-slip agent to the sealant and brush it on. It’s best to not walk or drive onto your new concrete driveway for about 4 days after sealing to allow everything to set. But after that, you’re ready to use your new driveway!

Are you having weed problems on your carefully picked out block pavings? After spending huge bucks to install the block pavings, the last thing any homeowner would want to discover is weed taking over the prized asset. Fortunately, this is a problem that can be effectively handled in a few simple steps provided in this article.

Basically, sealing of block paving is all about prevention of weed growth in the area by total weed removal, putting of sand between the block paving joints and sealing with a good quality sealant. This is a task that’s best left for a reliable professional to guarantee the best results especially if you lack proper training and experience. This guide will give a good insight into the process.

Here are the equipment you’ll need to get started: pressure washer, weed killer, bin bag, broom, small brush, protective gear, sealing roller, spueegee, jointing sand and sealer and DIY sprayer.

lRemove The Weed

• Put on a protective clothing and gloves

• Get a weed disposal bag to clean while you go.

• Apply the selected weed killer on both areas where weeds are present and the absent ones to prevent any growing.

lPressure Washing

• Angle your pressure washer between the gaps. This is done to remove all weeds and debris that are still lying around as well as removing all possible chemical residues to create a thorough clean between the paving slab.

• Leave the washed area to dry.

l Sand The Joints

• Check the weather forecast to ensure there’s about 24 to 48 hours of dryness as its important for both sand and sealant to do a perfect job.

• Put sand between the gaps and push it down with your small brush until its levelled.

lSeal The Gaps

• The sealing process should be done immediately and sanding.

• Clean up the patio

• Perform a test using a small area

• Apply the sealant

• Apply the second of sealant

• Leave to dry for about 2 to 3 hours.

Can You Lay Block Paving On Top Of Concrete?

The replacement or improvement of your driveway is unarguably one of the most expensive projects you can undertake in the exterior of your home. When done by a true professional the results can be impressive and visually appealing, however you’d have to pay huge bucks to have this done. This is exactly the situation with block paving as it is not only time consuming, but also a lot more expensive when compared to other types of driveway.

A large chuck of this cost is associated with the removal of the existing driveway. So assuming your old driveway is concrete, can you simply pave over the existing concrete? If yes, will it save you money? The simple and short answer is yes. It’s in fact advisable to pave over concrete as this will not only add around 20% to your home’s value, but also make it look a lot more attractive and pleasing to the eye.

However, there are some problems associated with block paving over concrete. It may be better to remove the concrete in situations whereby the base is substandard. For instance, if the ground underneath the concrete is failing, there’ll most definitely be problems.

Also, there’ll be some issues with settling (not even the cracks). If your concrete is dropping little amounts every year, these can affect the blocks and ultimately lead to dropping of some sections of the block paving in such a way that they’ll no longer be on the same level as the other blocks. Giving a rise to the possibility of drainage issues, tripping hazard and lots more.

Other issues that may crop up can be triggered as a result of using the wrong size block height as well as totally ignoring or overlooking the undulations of the concrete.

It’s up to you what size gravel you use for your driveway, but there are some guidelines that are worth following. If you go too small, your gravel will get displaced easily. But, if you go too big, you driveway might be quite tricky to walk on. Generally, it’s a good idea to go for a gravel size somewhere between 10-20mm.

Being a strong and durable product requiring little maintenance and expected to last over 2 decades, it’s little wonder resin is now a popular material amongst homeowners in the UK to build their driveways. However, there’s always the issue of the driveway fading, cracking or even becoming worn and tired. So is it possible to repair resin driveways? The answer is yes, a resin driveway can be repaired, however the best approach to use largely depends on the issue being faced. As a confident DIYer it’ll be very easy to do, but if you lack the confidence then calling in a professional for help would be a better option. So let’s take a look at how you can repair your resin driveways.

For cracks, the best reparation approach would be to chisel it out. Once done, then you can proceed to breaking the stones to form a rough edge. It’s important to make sure that the matrix of the stone remains unaffected. Make a new mixture of resin bound stone and pack it in tightly to the gap. While doing this, we’ll recommend making use of a plastic trowel to avoid burnishing. This fresh mixture will then create a smooth and perfect surface by interlocking with the edges. You can follow similar procedure for patches but these are larger holes or damages than cracks and as the name suggests are mostly likely to remain noticeable but will prevent further crumbling of your resin driveway.

For homeowners, who aren’t so keen about the patch repairs, you can opt for an overlay especially in the event whereby the majority of the surface has failed. Although many usually shy away from this approach because of the perceived high expenses, but the fact is that the approach is actually cost effective as you won’t have the need to spend more money in the long run.

Driveway surfacing materials like concrete, asphalt and clay brick usually crack because they’ve been exposed to extreme temperatures or put under high pressure. It’s important to repair driveway cracks before they get worse and cause damage to vehicles and perhaps others to trip on raised cracks.

If you want your tarmac driveway or outdoor area to last as long as possible, it’s important to look after it. This means giving it a good clean every so often.

If there are any greasy or oily stains on your tarmac, you won’t get these off only using water. Get a degreaser and follow the instructions. You’ll then need to use a pressure washer or hose to rinse off the detergent and clean the rest of your tarmac or asphalt area.

Avoid getting your pressure washer too close to your outdoor surface or pointing it directly at it. You should also avoid cleaning the same area for too long. This will help you clean your tarmac while avoiding damaging it.