Find a Driveway Installer you can trust in Glenfinnan.

While resin bound and resin bonded driveways have similar names, it might surprise you to know that they’re very different. Both paving systems use resin and aggregates (stones) to form a fixed surface, but there are plenty more differences than there are similarities.

Resin bound driveways are made from a resin and aggregate mix that is trowelled onto a bitmac or concrete base. It leaves a smooth, flat finish and you won’t find any loose gravel. It’s also a pourous surface, which means that rainwater can pass through into the ground, avoiding pools and flooding.

However, resin bonded driveways involve spreading resin across a base, then scattering aggregate into it. Most of the stones will stick to the resin, but some will stay loose. That means you’ll get the effect of loose gravel without so much to sweep and take care of. Because the stones are scattered onto a complete layer of resin, water can’t pass through it. That means you could end up with water pooling, and it also means that a resin bonded driveway isn’t frost resistant, meaning it could get slippery.

So which is better – a resin bound or resin bonded driveway? The answer depends on a few things. If you have a period property where a smooth, shiny surface might not complement the look of your home, you might want to go for resin bonded. If you need lots of grip, for example if you’re a wheelchair user, resin bonded may also be the way to go – even though resin bound surfaces still offer enough grip for sloped driveways and ramps. But if you want a low-maintenance, weed-free, permeable surface, resin bound driveways are the way to go.

If your concrete driveway’s looking grubby, it’s best to try cleaning it with water and a brush, or a mild detergent. However, if this doesn’t work, it can be worth trying bleach.

Dilute your bleach down to 50% bleach and 50% water, and apply it to your driveway. Leave it for 10 minutes, then scrub it using gloves and a stiff brush. Finish by rinsing your driveway off with clean water.

It’s important to remember that bleach can stain certain surfaces and kill plants. So, if you’re concerned about materials and boarders around your driveway, it might be best to use a different type of detergent, like floor cleaner or degreaser.

A patio is an outdoor space which can be used for a variety of stuffs which includes fun time with family and friends, reading time or just relaxing as the fresh breeze blows. With all these benefits and more, it’s becomes more obvious that there’s a need to keep your patio in a tip top condition at all times. If otherwise, you may not be able to enjoy your patio to your satisfaction and probably, for as long as you would want. You simply have to provide it with a regular maintenance which involves inspecting and identifying the damages that needs to be repaired before it gets out of hand. Fortunately, the minor repairs can be done by yourself if you’re confident enough. However, for bigger damages it’s advisable to call in a professional for help. In this article, we’ll take you through the patio reparation process.

✓ Prepare the area. This involves removing the problem piece gently and carefully. If there’s a piece you think can still be useful, store it in the re-use pile or you can start a new one. Once you’re done removing the pieces, the next thing to do would be to start removing anything that’s unwanted from the damaged area like debris, unwanted soil etc, and start sand fitting with some fresh sand. This should be levelled out to ensure there’s no bumps.

✓ With the sand down, you can start by putting the pieces back in together. This should be done gently to avoid any further damage. Do this until your patio

✓

Is Block Paving Permeable?

Back in 2008, there was a regulation introduced which comes with a requirement guiding the pavement of front gardens. It requires homeowners to incorporate the conventional impermeable driveways which makes for an uncontrolled run off of rainwater into sewers, roadways, local watercourses etc. However since then, new systems have been established which complies with the legislation and permit driveway laying of block paving without requiring planning permission while still providing the same visually appealing features as the conventional systems. Therefore, a short and simple answer to whether block paving is permeable is yes.

A permeable paving driveway (unlike the conventional ones which quickly diverts rainwater towards the edges to local drains) purposefully diverts rainwater into the built paving structure which oversees a controlled release of the rainwater into the environment. Permeable block paving comes with a wide range of benefits which includes the following:

• No Planning Permission Required

Unlike the traditional system, permeable block paving requires no planning permission as it oversees the driveway draining by ensuring that the surface water passes directly through the joints which makes sure the drains are not over worked and minimizing the risk of flood.

• Puddles Reduction By Natural Drainage

A permeable block paving minimizes puddles as well as standing water which helps to boost natural drainage. This is due to the laying process which features little voids that permits the passage of water.

• Natural Filtration

A natural filtration occurs when water is allowed to return to the ground by permeable block paving which helps assists in getting rid of any pollutants from the rain water.

• Flood Prevention

Permeable paving can help to prevent flooding as it absorbs water rather than directing it to the local drains or leaving it to build up on the surface’s top.

• Natural & Sustainable Materials

Natural and recyclable materials can be incorporated in producing permeable paving which is an excellent choice especially if you’re seeking a more sustainable driveway.

How To Lay Block Paving

Do you wish to know how to install block paving? We’ve got you covered! Here, you’ll find a useful step by step guide that’ll provide you with all the necessary information to lay a wide range of block paving products available in the market today. You must, however, note that the installation of block paving can be a tricky affair and should not be attempted unless you have undergone a proper training or have a good experience in the field. If otherwise, we’d advise you to leave the task for a reliable block laying professional to guarantee the best results and also avoid making costly mistakes.

lDesign

• Draw up a design to perfectly suits your needs.

• Decide on the type of block as well as colour.

lExcavation

• Use a mini excavator or a JCB ( depending on the size of the job) to excavate the driveway.

• Identify and mark out the area to be excavated.

• Dug out the area until you reach a suitable level

• Ensure that the proposed finish level is 150mm underneath the damp proof course in any of the adjoining building’s brick.

lEdge Restraints

• Build a 100mm depth-thick concrete foundation with the help of a concrete mixer, 1 part cement and 6 parts ballast.

• Position the kerb unit on top of the level with a string line and spirit level.

• Use a trowel and rubber mallet to mortar the kerb unit to the foundation.

• Haunch the back of the kerb units in such a way that the concrete reach half way up the kerb’s rear.

lSubbase

• Put the crushed concrete in the edge restraints and ensure it’s at the desired level of 50mm.

• Use a vibrating plate to compact and level

lScreeding

• Apply a layer of sharp sand (to 50mm depth) and campact it using a vibrating plate.

• Apply second layer of sharp sand (to 20mm depth) on top of the first layer.

• Level the second layer to the correct falls.

lInstallation Of Paving

• Lay the block paving starting from the bottom of a slope.

• Ensure the blocks are placed at about 10mm to 15mm above the required finish level.

• Make sure the blocks used are between 3-5 packs as you proceed with your desired pattern. You may need to cut smaller block pieces to fill smaller gaps.

lFinishing Touches

• Clear out the area to ensure no debris is left on the blocks.

• Put kiln dried sand and brush across the whole of the area, ensuring the sands falls between the blocks’ joints.

• Compact the drive with the vibrating plate.

• Brush more kiln dried sand over the area and compact again

• Repeat the process until the joints are full of sand.

How To Repair Sunken Concrete Driveway

If you have concrete driveway that’s cracked, uneven and mostly especially sunken, you’d know how distasteful it can be just viewing it on your property. A sunken concrete driveway is most likely caused by rainwater erosion removing the soil under it or a big root under it which as rotted over time. Another possible cause of the sunken concrete is an improperly prepared base which implies that the soil beneath wasn’t fully compact when the concrete was poured on it. Later on the soil beneath will eventually settle and shift below the concrete driveway which weakens the integrity of the entire driveway, making it more vulnerable to cracks, unevenness and sunken.

Two ways in which you can fix this problem includes either demolishing the whole driveway, re-compact the soil underneath and fill with new concrete or repair the entire driveway using an easy process called slabjacking. In this article, we’re going to look at the slabjacking repair process as it’s significantly less expensive than the demolishing approach and will also cause minimal disruption to your lifestyle.

Also referred to as mudjacking or concrete lifting, slabjacking is simply a process used to float your existing concrete back to its original position. If you are not a competent DIYer or lack confidence to pull this off, we’d recommend reach out to a professional for help. If otherwise, then you can practice the slabjacking process given below.

✓ Drill holes through the slab.

✓ Pump grout mixture through the holes. This mixture will spread out beneath he driveway and raise it up.

✓ Lastly, fill the holes and level the concrete driveway surface.in such a way to hide the signs of the repair made.

This is a process that works to efficiently get your driveway back in a top condition relatively quickly.

1. Prepare the base If you want your resin bound driveway to last a long time, you need to ensure that you prepare the base properly. Remove any block paving, grass or soil and dig down until you hit solid ground. Lay a sub-base of asphalt for good permeability. If you’re laying over the top of your current driveway, make sure that all cracks are increased into a ‘v’ shape with a saw and ensure the surface is dry and weed-free.
2. Mix the resin You must follow the instructions on the materials you have to the letter if you want the curing process to work. Usually batches come in ‘Part A’ and ‘Part B’. Keep the resin container secure and on a protective surface to avoid splashing, then mix Part A for 10-20 seconds at a slow speed with a helical bladed mixer. Add Part B and mix thoroughly at a slow speed for about 2 minutes until it’s blended together.
3. Mix the dried aggregates and sand with the resin Place a quarter of the aggregates into a mixer, then add the pre-mixed resin and start a stopwatch. You should then add the rest of the aggregates before slowly adding the sand. When you’re happy with that mix, stop the stopwatch. That time is the time that you need to spend mixing any other resin and aggregates to avoid colour variation.
4. Lay the mix on the surface Transfer the mix to the work area then plan a laying route. When the mix is laid out, use a very clean trowel to spread the mix. Clean it regularly during the process to avoid dragging aggregates out of place. Once the aggregates stop moving in a fluid movement and become solid, stop trowelling. Then you can polish the surface to give it an attractive shine.

Being a fantastic alternative to slabs or block paves, gravel drive way slowly becoming an extremely popular driveway surfacing option in the UK. Not only does gravel driveway value adding investment to a home, but also allows you to be very creative and can make a beautiful addition to your home.

It’s normal to think that having a new gravel laid is a herculean task but when the necessary tools and materials are within your reach then it’s a fair simple task for the competent DIYer. So if you’re about to lay your new gravel driveway option of your home and wondering how deep to dig the driveway, then you’ve come to the right place. There are times, however, that the best option would be to hire a reliable and trustworthy professional who can guarantee the best results while also helping you save time and additional expenses which could result from costly mistakes. However, in this guide, we offer some handy tips on the appropriate depth of a gravel driveway in order to put you on the right path from the start. So let’s take a closer look!

Normally, it’s required to lay a a 10 mm aggregate on a depth which should be within the range of 30 mm to 40 mm. However in the case of driveway, this structure must be at least 50mm deep. As a result of this requirement, you’ll require to dig a minimum depth of about 50 mm to 60mm on your driveway. If you’re using a larger aggregate, it’s going to settle and bond together more easily than the smaller alternatives. Therefore, the depth of your driveway will mostly be determined by the size of the aggregate you opt for as well as how you intend to use the surface.