Find a Driveway Installer you can trust in Aylesford.

Creating a tarmac path or driveway is a tricky process. It’s a job best left to professionals who know what they’re doing, as there are plenty of opportunities for it go wrong. However, even if you’re planning to hire someone to do it for you, it’s worth knowing how it’s done.

Firstly, you’ll need to remove any existing path or driveway and excavate down to formation level – about 175mm below paving level. Then, a membrane is laid down to prevent weed growth.

Next, a sub-base goes down, usually made of crushed rock or concrete. This is compacted and the tarmac is laid over the top. This is put down in two layers, and is rolled to make it compact and smooth.

It’s important to use edging when laying tarmac, to ensure that it doesn’t run off where you want your path or driveway to be. Tarmac paving and driveways also needs suitable drainage.

The best way to clean resin bound driveways is to sweep it regularly with a stiff broom. This will remove any debris and prevent moss from growing. It's a good idea to jet wash it after sweeping, because this will get rid of any smaller parts that a broom might not collect.

When you jet wash or power wash your resin bound driveway, make sure the pressure isn’t too high. It’s recommended to keep the pressure less than 150bar, as anything too strong could damage the surface. Make sure the water is cool, but not cold – both hot and cold water can damage the resin. Make sure the jet wash nozzle is at least 20cm from the surface. Any closer and this could damage your driveway. Use a sweeping back and forth motion to clean.

If you treat the area before you have your resin bound driveway installed, you shouldn’t get any weed growth. But if you get any moss or algae appear, you can apply a moss and algae killer that should remove and prevent any regrowth. If you have ingrained algae, you can remove it with a strong bleach solution; make sure you follow the manufacturer’s instructions. This should also help restore the driveway’s original colour. Make sure you rinse your driveway thoroughly with clean water after using bleach on it to prevent any harm to wildlife or plants.

If you get chewing gum on your resin bound driveway and you can’t get it off with a pressure washer, try using a freezing spray on it first. Then use a wall scraper to gently remove it – never dig under the chewing gum as this could damage the resin on your driveway.

Being a fantastic alternative to slabs or block paves, gravel drive way slowly becoming an extremely popular driveway surfacing option in the UK. Not only does gravel driveway value adding investment to a home, but also allows you to be very creative and can make a beautiful addition to your home.

It’s normal to think that having a new gravel laid is a herculean task but when the necessary tools and materials are within your reach then it’s a fair simple task for the competent DIYer. So if you’re about to lay your new gravel driveway option of your home and wondering how deep to dig the driveway, then you’ve come to the right place. There are times, however, that the best option would be to hire a reliable and trustworthy professional who can guarantee the best results while also helping you save time and additional expenses which could result from costly mistakes. However, in this guide, we offer some handy tips on the appropriate depth of a gravel driveway in order to put you on the right path from the start. So let’s take a closer look!

Normally, it’s required to lay a a 10 mm aggregate on a depth which should be within the range of 30 mm to 40 mm. However in the case of driveway, this structure must be at least 50mm deep. As a result of this requirement, you’ll require to dig a minimum depth of about 50 mm to 60mm on your driveway. If you’re using a larger aggregate, it’s going to settle and bond together more easily than the smaller alternatives. Therefore, the depth of your driveway will mostly be determined by the size of the aggregate you opt for as well as how you intend to use the surface.

It’s up to you what size gravel you use for your driveway, but there are some guidelines that are worth following. If you go too small, your gravel will get displaced easily. But, if you go too big, you driveway might be quite tricky to walk on. Generally, it’s a good idea to go for a gravel size somewhere between 10-20mm.

Do you know why paving slaps is a popular choice for both driveways and patios? Well, it’s the versatility! With its durability, diverse colour range, different styles as well as a timeless appeal, paving slabs happen to be a common choice amongst home owners. However, you should know that redeeming these benefits is not as simple as shovelling mortar and pressing down the paving slabs, and neither is it a case whereby you can just copy the laying process of a porcelain paving or block paving. Laying of paving slabs is on a whole other level! As a result, we’d recommend employing a trustworthy professional who can guarantee the best results the first time, especially if you lack proper training or experience to complete the task. In this step by step guide, you’ll discover more about the paving slabs laying process.

• Prepare your paving foundation. This includes checking that your foundation is level, marking out the area to be paved with wooden pegs, removing all vegetation and top soil to a depth of about 200mm to 250mm and raking the area level to ensure and even depth.

• Mix a layer of mortar for each paver and apply the mixed mortar onto the sub base by using the trowel.

• Lay the slabs on top of the laying course at the lowest point of the area to be paved.

• Take note that you may need to cut some slabs depending on the paving area size, your chosen slabs and the pattern selected.

• Once done, brush the area clean and start jointing. The best way to do this is by applying kiln dried sand to the paved area and carefully brush into the joints with a brush.

• Push the sands into the joints using a plate compactor

• Check the paved area for any gaps and fill where necessary.

Is Block Paving Permeable?

Back in 2008, there was a regulation introduced which comes with a requirement guiding the pavement of front gardens. It requires homeowners to incorporate the conventional impermeable driveways which makes for an uncontrolled run off of rainwater into sewers, roadways, local watercourses etc. However since then, new systems have been established which complies with the legislation and permit driveway laying of block paving without requiring planning permission while still providing the same visually appealing features as the conventional systems. Therefore, a short and simple answer to whether block paving is permeable is yes.

A permeable paving driveway (unlike the conventional ones which quickly diverts rainwater towards the edges to local drains) purposefully diverts rainwater into the built paving structure which oversees a controlled release of the rainwater into the environment. Permeable block paving comes with a wide range of benefits which includes the following:

• No Planning Permission Required

Unlike the traditional system, permeable block paving requires no planning permission as it oversees the driveway draining by ensuring that the surface water passes directly through the joints which makes sure the drains are not over worked and minimizing the risk of flood.

• Puddles Reduction By Natural Drainage

A permeable block paving minimizes puddles as well as standing water which helps to boost natural drainage. This is due to the laying process which features little voids that permits the passage of water.

• Natural Filtration

A natural filtration occurs when water is allowed to return to the ground by permeable block paving which helps assists in getting rid of any pollutants from the rain water.

• Flood Prevention

Permeable paving can help to prevent flooding as it absorbs water rather than directing it to the local drains or leaving it to build up on the surface’s top.

• Natural & Sustainable Materials

Natural and recyclable materials can be incorporated in producing permeable paving which is an excellent choice especially if you’re seeking a more sustainable driveway.

Gravel is the cheapest driveway surfacing material. Asphalt costs a little more than gravel, and concrete is significantly more expensive. The cost of paving depends on the material you use. Obtain as many quotes as possible as materials and costs differ from company to company.

Indian stone paving is just an one-of-a-kind kind of natural stone which is often made use of for driveways, patios and neat pathways. Been preferred amongst residence and also homeowner given that the 90s, Indian stone paving as the name suggests are generally imported from India - a nation widely recognized for their vibrant naturally veined natural stone. Because of this, Indian stone paving stands out from the crowd and also regulates certain regard within the landscaping globe and a lot more importantly, without the huge price tag of other high end alternatives such as Yorkstone.

With Indian stone paving vast array of colour profiles and also tone variations, they have the ability to stick out easily when set up on driveways. Several of the most popular colour alternatives is the single toned limestone or the Indian sandstone paving slabs for a weather-beaten style.

The ideal driveway has to be really resilient and durable, visual pleasing and additionally inexpensive. Luckily, these are all divisions that the Indian stone paving succeeds quite remarkably. When it pertains to upkeep, the Indian sandstone paving is very to clean as well as maintain. Dusts gathered with time will certainly be removed by the rainfall, and all that's left can quickly be erased or hosed down. The rock additionally fits flawlessly right into any type of driveway as its rather easy to install. This is that type of paving that can just be laid without needing to bother with a thing.

With the various advantages that features the Indian stone paving, from the sturdiness and also safety to low upkeep requirements and visual appeal, it would certainly be regular to presume that it would be quite expensive to set up. Nevertheless, in truth, there are a plethora of mid range stone alternatives hat takes place to be extremely budget-friendly especially when compared to various other comparable natural stones.