Find a Driveway Installer you can trust in Larkhall.

Whether you think resin bound driveways are expensive or not will depend on your perception. While resin bound driveways are the most expensive up front, they should last much longer than other types of driveway. You should expect a resin bound driveway to last at least 25 years, if not longer, while a concrete or asphalt driveway may last between 15-20 years. A pattern imprinted driveway may last even less time due to the maintenance required to keep them looking pristine.

It’s also worth considering that resin bound driveways are good permeable surfaces, so will drain well and keep water from pooling around your property. This will keep your property maintenance costs down, since pooling water or flooding around your home could cause damp in your walls which is a very expensive problem to fix.

Resin bound driveways are by far the most attractive type of driveway to have. There are no loose stones to sweep up, no weeds to pull out from the gaps, and there’s no extensive power washing required to keep them looking good. If you want a driveway that gives your home true kerb appeal and you value your time, resin bound driveways don’t seem that expensive.

The other factor that can make resin bonded driveways less expensive is that sometimes you can lay them on top of the existing surface. For example, if you already have a concrete or asphalt driveway that is in good condition with no large cracks, a driveway contractor may be able to lay the resin and aggregate mix straight over the top, which will cost much less money than if you have to dig up the existing driveway and start from scratch.

A resin bound driveway is made from resin and aggregates that are mixed together to create a smooth, flat surface. They’re often called ‘stone carpets’ because they offer a decorative finish that is durable and requires very little maintenance. It has lots of little gaps that allow water to drain into the ground, which means that you won’t get pooling or flooding around your property.

You can choose from lots of different colours and types of aggregate (stones) so that your resin bound driveway complements your property. Most contractors recommend choosing a darker aggregate because they are more resistant to the sun, but if you choose a good UV-resistant resin you should be able to have a lighter stone that doesn’t get too bleached by the sun.

To lay a resin bound driveway, resin and aggregates are mixed in a forced action mixer to create a mixture that a tradesperson will then pour and trowel onto a prepared base. It will become smooth once it’s cured, and the stones will all be contained, so you won’t have to spend time sweeping gravel back onto your driveway. The only maintenance that’s needed is to wash it with soapy water every now and again and sweep away any debris. Just make sure you don’t use chemicals or oils, as this might damage the coating.

Do you want to know the level of thickness a driveway concrete slab should be? Well, you are not alone! So many other home owners ask this question on a regular basis and reasonably so. In order to prevent cracks on your concrete over time, it’s crucial to ensure an even thickness across your driveway concrete. To determine the necessary thickness of your driveway concrete, there are some questions that must be answered. These includes:

• What’s the number of vehicles you expect to have on your driveway?

• Do you plan on parking heavy, industrial vehicles on it?

For a standard passenger vehicle driveway, you’d have a driveway spanning 8 to 9 feet in width as well as 15 to 18 feet for double width. The thickness for this type of driveway concrete is usually 4 inches of non-reinforced pavement. Ultimately, this enables you to park everyday family cars on it without having to worry about it cracking due to the car’s weight. Also in order to prevent cracks, it’s expected that the driveway should be sloped towards the street as this would make sure that there’s a run off of water especially for areas that experience lots of flooding. In addition, there’s also the need to install joints to prevent cracking. For the standard 4 inch thick driveway, these joints should be positioned about 10 feet apart.

Finally for parking heavy industrial vehicles, your concrete driveway is expected to be thicker in order to cope with the added weight. Typically, the concrete driveway will require a thickness of about 5 inches. The additional one inch may not sound much, but the fact is this can increase the load carrying capacity of the concrete driveway by up to 50 percent.

Are you having weed problems on your carefully picked out block pavings? After spending huge bucks to install the block pavings, the last thing any homeowner would want to discover is weed taking over the prized asset. Fortunately, this is a problem that can be effectively handled in a few simple steps provided in this article.

Basically, sealing of block paving is all about prevention of weed growth in the area by total weed removal, putting of sand between the block paving joints and sealing with a good quality sealant. This is a task that’s best left for a reliable professional to guarantee the best results especially if you lack proper training and experience. This guide will give a good insight into the process.

Here are the equipment you’ll need to get started: pressure washer, weed killer, bin bag, broom, small brush, protective gear, sealing roller, spueegee, jointing sand and sealer and DIY sprayer.

lRemove The Weed

• Put on a protective clothing and gloves

• Get a weed disposal bag to clean while you go.

• Apply the selected weed killer on both areas where weeds are present and the absent ones to prevent any growing.

lPressure Washing

• Angle your pressure washer between the gaps. This is done to remove all weeds and debris that are still lying around as well as removing all possible chemical residues to create a thorough clean between the paving slab.

• Leave the washed area to dry.

l Sand The Joints

• Check the weather forecast to ensure there’s about 24 to 48 hours of dryness as its important for both sand and sealant to do a perfect job.

• Put sand between the gaps and push it down with your small brush until its levelled.

lSeal The Gaps

• The sealing process should be done immediately and sanding.

• Clean up the patio

• Perform a test using a small area

• Apply the sealant

• Apply the second of sealant

• Leave to dry for about 2 to 3 hours.

The best way to clean resin bound driveways is to sweep it regularly with a stiff broom. This will remove any debris and prevent moss from growing. It's a good idea to jet wash it after sweeping, because this will get rid of any smaller parts that a broom might not collect.

When you jet wash or power wash your resin bound driveway, make sure the pressure isn’t too high. It’s recommended to keep the pressure less than 150bar, as anything too strong could damage the surface. Make sure the water is cool, but not cold – both hot and cold water can damage the resin. Make sure the jet wash nozzle is at least 20cm from the surface. Any closer and this could damage your driveway. Use a sweeping back and forth motion to clean.

If you treat the area before you have your resin bound driveway installed, you shouldn’t get any weed growth. But if you get any moss or algae appear, you can apply a moss and algae killer that should remove and prevent any regrowth. If you have ingrained algae, you can remove it with a strong bleach solution; make sure you follow the manufacturer’s instructions. This should also help restore the driveway’s original colour. Make sure you rinse your driveway thoroughly with clean water after using bleach on it to prevent any harm to wildlife or plants.

If you get chewing gum on your resin bound driveway and you can’t get it off with a pressure washer, try using a freezing spray on it first. Then use a wall scraper to gently remove it – never dig under the chewing gum as this could damage the resin on your driveway.

Tarmac is a material made up of broken stone and tar, used for surfacing roads, driveways and other outdoor areas. It’s actually a registered product trademark, but many people use ‘tarmac’ interchangeably with ‘asphalt’. Asphalt is similar to tarmac, but is now more commonly used, and is made from bitumen instead of tar.

Being a strong and durable product requiring little maintenance and expected to last over 2 decades, it’s little wonder resin is now a popular material amongst homeowners in the UK to build their driveways. However, there’s always the issue of the driveway fading, cracking or even becoming worn and tired. So is it possible to repair resin driveways? The answer is yes, a resin driveway can be repaired, however the best approach to use largely depends on the issue being faced. As a confident DIYer it’ll be very easy to do, but if you lack the confidence then calling in a professional for help would be a better option. So let’s take a look at how you can repair your resin driveways.

For cracks, the best reparation approach would be to chisel it out. Once done, then you can proceed to breaking the stones to form a rough edge. It’s important to make sure that the matrix of the stone remains unaffected. Make a new mixture of resin bound stone and pack it in tightly to the gap. While doing this, we’ll recommend making use of a plastic trowel to avoid burnishing. This fresh mixture will then create a smooth and perfect surface by interlocking with the edges. You can follow similar procedure for patches but these are larger holes or damages than cracks and as the name suggests are mostly likely to remain noticeable but will prevent further crumbling of your resin driveway.

For homeowners, who aren’t so keen about the patch repairs, you can opt for an overlay especially in the event whereby the majority of the surface has failed. Although many usually shy away from this approach because of the perceived high expenses, but the fact is that the approach is actually cost effective as you won’t have the need to spend more money in the long run.