Find a Driveway Installer you can trust in Ashby-de-la-zouch.

1. Prepare the base If you want your resin bound driveway to last a long time, you need to ensure that you prepare the base properly. Remove any block paving, grass or soil and dig down until you hit solid ground. Lay a sub-base of asphalt for good permeability. If you’re laying over the top of your current driveway, make sure that all cracks are increased into a ‘v’ shape with a saw and ensure the surface is dry and weed-free.
2. Mix the resin You must follow the instructions on the materials you have to the letter if you want the curing process to work. Usually batches come in ‘Part A’ and ‘Part B’. Keep the resin container secure and on a protective surface to avoid splashing, then mix Part A for 10-20 seconds at a slow speed with a helical bladed mixer. Add Part B and mix thoroughly at a slow speed for about 2 minutes until it’s blended together.
3. Mix the dried aggregates and sand with the resin Place a quarter of the aggregates into a mixer, then add the pre-mixed resin and start a stopwatch. You should then add the rest of the aggregates before slowly adding the sand. When you’re happy with that mix, stop the stopwatch. That time is the time that you need to spend mixing any other resin and aggregates to avoid colour variation.
4. Lay the mix on the surface Transfer the mix to the work area then plan a laying route. When the mix is laid out, use a very clean trowel to spread the mix. Clean it regularly during the process to avoid dragging aggregates out of place. Once the aggregates stop moving in a fluid movement and become solid, stop trowelling. Then you can polish the surface to give it an attractive shine.

Do you want to install a new patio? If yes, then on top of the agenda will definitely be the cost of paving slabs. However providing a single and accurate estimate to the cost of your new patio is almost impossible as there are many factors that can influence what the price would be. These factors include the size of the area, the choice of stone, installations and lots more.

To get a more accurate estimate of your cost there’s is the need to look at some factors before calculation. These includes envisioning your patio as well as putting the drainage in mind. Firstly, you’ll need to decide where you want your patio to be - this should include considering whether you’ll get enough privacy sitting on your patio and more. If you’re able to identify where to put your patio, you’ll be able to have a clearer idea of the potential shape and size of the patio. Secondly, there’s a need to consider the drainage because failure to provide adequate drainage will only result in storing of water which leads to a development of algae or vegetation across your patio.

The material you opt for is also a huge determinant of your patio’s cost. When it comes to paving slabs you’ll only get what you pay for. Deciding to go for cheaper paving slabs will most likely lead to frequent staining, slippery surface, tough maintenance as well as constant cracking. Consequently, the act of cutting back on the cost of paving slabs will only you cost you more money in the long run. What’s more? If you have an existing patio you’d like to replace, then you’d probably need to include the cost of removing the existing one.

Patios use durable and hard wearing materials which will be able to withstand extreme weather. It’s important to consider the drainage of your patio, as heavy rain will need to drain away to an area that can absorb the water. A professional will be able to design and lay a patio to do this.

If your concrete driveway’s looking grubby, it’s best to try cleaning it with water and a brush, or a mild detergent. However, if this doesn’t work, it can be worth trying bleach.

Dilute your bleach down to 50% bleach and 50% water, and apply it to your driveway. Leave it for 10 minutes, then scrub it using gloves and a stiff brush. Finish by rinsing your driveway off with clean water.

It’s important to remember that bleach can stain certain surfaces and kill plants. So, if you’re concerned about materials and boarders around your driveway, it might be best to use a different type of detergent, like floor cleaner or degreaser.

Oil stains on your concrete driveway can look obvious and unsightly. However, there are several different ways to remove them.

If you’ve only just spilled the oil, you can use a mixture of absorbent material, like sawdust, and solvent, like acetone or lacquer. Combine these, place them on the stain, cover and leave for about 24 hours. Then sweep up the mixture and rinse the area with water.

If you’ve got a small, older stain, you can use a detergent like baking soda, vinegar, washing up liquid or laundry detergent. Cover the stain with the detergent and leave for about 30 minutes. Then, add hot water and scrub the area and rinse. You might need to repeat this if necessary.

If it’s a larger, more stubborn stain, you might need to use a special degreaser. You can use this similarly to a detergent but make sure you follow the instruction on the bottle carefully.

When your driveway is suffering from depression, it becomes unsafe for driving (a danger zone) and ugly - no homeowner wants that! Unfortunately, most driveways won’t hold flat for long as they tend to develop cracks and potholes pretty quickly. Here, we are going to take you through how to fill asphalt driveways’ depression so as to ensure the sinkholes in your driveway poses no threat to you or your loved ones, while also beautifying your property. The approach to be used depends on the intensity of the depression. If its only a few cracks and holes, this can easily be repaired with some equipment. But if otherwise is the case, then calling a reliable professional will be your best bet. In this article, we’ll show you how to repair dips in your asphalt driveway relatively quickly.

✓ Pick a date with warm and sunny weather. This is because if you work in a cold weather, chances are the materials will freeze and hence, unusable. So find a day when the temperature will over 50 degrees Fahrenheit and below 80 degrees Celsius and when there would be no rain. We’ll advise a day between May to October.

✓ Prepare the area. Remove all loose stones, soil, dirt as well as vegetation from the holes. Once done, you can then proceed to washing the area with a pressure washer or sweep with a broom.

✓ Apply a thin mixture of asphalt to the area. Use a flat stirring stick to coat the low driveway area with a thin mixture of asphalt.

✓ Tamp the asphalt repair mix. Purchase the right kind of asphalt to repair the driveway. Fine aggregate asphalt mixture is more suited to filling small holes, whereas the coarse aggregate is more suited to filling larger holes. Apply layers ( about 2 inches each time) of the asphalt repair mix to the sunken area and use a shovel to give it a smooth finish. Once done, simply make the area smooth and protect it with a piece of plywood. Do not walk or drive on the area for a couple of days.

The most commonly used driveway surfacing materials are gravel, asphalt, concrete and paving - which can be block, slabbed or patten imprinted. Take a look at our product information pages to help you decide which one to use and which one will look best for your driveway.

Gravel driveways are very popular in the UK for a reason. Not only do they provide a more natural look than other driveway surfacing options and happens to be quite affordable, but they’re also very easy to install and maintain. And more importantly, they have a great range of colour scheme to match and compliment your brickwork and plants to make for an alluring outdoor living space.

Are you also planning to install a gravel driveway? You’ve come to the right place! If you’re a competent DIYer with confidence, then this should be as easy as they come. If otherwise, then it’s advisable to hire a reliable professional who can guarantee the best results for help. In this guide, we’ll shed more light on the gravel driveway installation process. Let’s get started!

✓ Prepare the floor. To get a level and flat floor, you’ll have to clear the area of all weeds, paving slabs, block paving etc. Get a good foundation material to apply to the surface if you have an uneven surface or if you have potholes to fill.

✓ Stop the weeds. You’ll have to apply an anti-weed membrane so you won’t have stubborn weeds growing through your finished driveway.

✓ Spread the gravel. In the process of purchasing your gravel, ensure to select handy bags, bulk bags if tipped loose. If you go for the bags there may be a need of wheelbarrow to help move the gravel around, however with a tipped loose you can have the gravel chippings tipped directly on to the driveway.

✓ Make use of the hose. It’s possible that when your gravel arrives, it’ll be be dusty. Make use of an hose to run over the driveway to bring out the true colours of your driveway.