Find a Driveway Installer you can trust in Aberdare.

Creating a tarmac path or driveway is a tricky process. It’s a job best left to professionals who know what they’re doing, as there are plenty of opportunities for it go wrong. However, even if you’re planning to hire someone to do it for you, it’s worth knowing how it’s done.

Firstly, you’ll need to remove any existing path or driveway and excavate down to formation level – about 175mm below paving level. Then, a membrane is laid down to prevent weed growth.

Next, a sub-base goes down, usually made of crushed rock or concrete. This is compacted and the tarmac is laid over the top. This is put down in two layers, and is rolled to make it compact and smooth.

It’s important to use edging when laying tarmac, to ensure that it doesn’t run off where you want your path or driveway to be. Tarmac paving and driveways also needs suitable drainage.

When your driveway is suffering from depression, it becomes unsafe for driving (a danger zone) and ugly - no homeowner wants that! Unfortunately, most driveways won’t hold flat for long as they tend to develop cracks and potholes pretty quickly. Here, we are going to take you through how to fill asphalt driveways’ depression so as to ensure the sinkholes in your driveway poses no threat to you or your loved ones, while also beautifying your property. The approach to be used depends on the intensity of the depression. If its only a few cracks and holes, this can easily be repaired with some equipment. But if otherwise is the case, then calling a reliable professional will be your best bet. In this article, we’ll show you how to repair dips in your asphalt driveway relatively quickly.

✓ Pick a date with warm and sunny weather. This is because if you work in a cold weather, chances are the materials will freeze and hence, unusable. So find a day when the temperature will over 50 degrees Fahrenheit and below 80 degrees Celsius and when there would be no rain. We’ll advise a day between May to October.

✓ Prepare the area. Remove all loose stones, soil, dirt as well as vegetation from the holes. Once done, you can then proceed to washing the area with a pressure washer or sweep with a broom.

✓ Apply a thin mixture of asphalt to the area. Use a flat stirring stick to coat the low driveway area with a thin mixture of asphalt.

✓ Tamp the asphalt repair mix. Purchase the right kind of asphalt to repair the driveway. Fine aggregate asphalt mixture is more suited to filling small holes, whereas the coarse aggregate is more suited to filling larger holes. Apply layers ( about 2 inches each time) of the asphalt repair mix to the sunken area and use a shovel to give it a smooth finish. Once done, simply make the area smooth and protect it with a piece of plywood. Do not walk or drive on the area for a couple of days.

If you want to give your concrete paving slabs a new lease of life, it’s possible to paint them. This is a great option if your slabs are looking tired or you want a new look, but you don’t want to invest in new paving.

Before you go ahead, you need to make sure that your slab paving is clean and dry. And if it’s been sealed, you’ll need to strip this off. Make sure you get a paint that’s specifically designed for the job so you get the best results.

Tarmac is a material made up of broken stone and tar, used for surfacing roads, driveways and other outdoor areas. It’s actually a registered product trademark, but many people use ‘tarmac’ interchangeably with ‘asphalt’. Asphalt is similar to tarmac, but is now more commonly used, and is made from bitumen instead of tar.

Do you know why paving slaps is a popular choice for both driveways and patios? Well, it’s the versatility! With its durability, diverse colour range, different styles as well as a timeless appeal, paving slabs happen to be a common choice amongst home owners. However, you should know that redeeming these benefits is not as simple as shovelling mortar and pressing down the paving slabs, and neither is it a case whereby you can just copy the laying process of a porcelain paving or block paving. Laying of paving slabs is on a whole other level! As a result, we’d recommend employing a trustworthy professional who can guarantee the best results the first time, especially if you lack proper training or experience to complete the task. In this step by step guide, you’ll discover more about the paving slabs laying process.

• Prepare your paving foundation. This includes checking that your foundation is level, marking out the area to be paved with wooden pegs, removing all vegetation and top soil to a depth of about 200mm to 250mm and raking the area level to ensure and even depth.

• Mix a layer of mortar for each paver and apply the mixed mortar onto the sub base by using the trowel.

• Lay the slabs on top of the laying course at the lowest point of the area to be paved.

• Take note that you may need to cut some slabs depending on the paving area size, your chosen slabs and the pattern selected.

• Once done, brush the area clean and start jointing. The best way to do this is by applying kiln dried sand to the paved area and carefully brush into the joints with a brush.

• Push the sands into the joints using a plate compactor

• Check the paved area for any gaps and fill where necessary.

The most commonly used driveway surfacing materials are gravel, asphalt, concrete and paving - which can be block, slabbed or patten imprinted. Take a look at our product information pages to help you decide which one to use and which one will look best for your driveway.

If you’re considering giving your home a quick facelift, laying of paving slabs for your outdoor living spaces might be a great way to start. It can be installed in some many parts of your home’s exterior from the pathways to driveways and from the yards to the patios. With proper training and experience, laying paving slabs is a very easy and quick process. However, the issue here is, how do you calculate the number of paving slabs you need? In this step by step guide, you’ll find all the information needed to help you get started. Once you’re able to get the accurate number of paving slabs, do ensure to include extras that’ll cover up for possible errors or damages.

Just like any other measurement task, it’ll be a lot easier when you know how as well as when you have the right tools to use for the job. To get started, you’ll need a tape measure, pen or pencil, pegs, string, hammer, paper and calculator.

• Draw a sketch of the area. This sketch will take note of the area’s length and width.

• Using strings and pegs, mark out the area to be paved

• Using a tape measure, take a measurement of the length and width of the space along the string lines and note them on the sketch.

• If the area is a drive make sure that the paved area is wide enough to accommodate the cars intended

• Multiply the length of the space by the width to get the area of the space.

• Once calculated, divide the total area of the space by the area of the single slab. This will give you an accurate number of the paving slabs you’ll require to complete your project.

It’s up to you what size gravel you use for your driveway, but there are some guidelines that are worth following. If you go too small, your gravel will get displaced easily. But, if you go too big, you driveway might be quite tricky to walk on. Generally, it’s a good idea to go for a gravel size somewhere between 10-20mm.