Find a Driveway Installer you can trust in Caerphilly.

Clearing snow from a gravel driveway can be tricky – you need to remove the snow without taking the gravel with it.

If the snow’s quite light and dry, try using a leaf blower. You might find that this is enough to get the snow out the way. If it isn’t, start by using a shovel. Use this to clear the top layer of snow off your driveway, leaving about an inch behind. Then, use a rake to remove most of the remaining snow. This won’t take away 100% of the snow or leave all of your gravel in place, but it’s still pretty effective. You can then lay salt to melt away the rest of the snow and stop it turning into ice.

Creating a tarmac path or driveway is a tricky process. It’s a job best left to professionals who know what they’re doing, as there are plenty of opportunities for it go wrong. However, even if you’re planning to hire someone to do it for you, it’s worth knowing how it’s done.

Firstly, you’ll need to remove any existing path or driveway and excavate down to formation level – about 175mm below paving level. Then, a membrane is laid down to prevent weed growth.

Next, a sub-base goes down, usually made of crushed rock or concrete. This is compacted and the tarmac is laid over the top. This is put down in two layers, and is rolled to make it compact and smooth.

It’s important to use edging when laying tarmac, to ensure that it doesn’t run off where you want your path or driveway to be. Tarmac paving and driveways also needs suitable drainage.

Oil stains on your concrete driveway can look obvious and unsightly. However, there are several different ways to remove them.

If you’ve only just spilled the oil, you can use a mixture of absorbent material, like sawdust, and solvent, like acetone or lacquer. Combine these, place them on the stain, cover and leave for about 24 hours. Then sweep up the mixture and rinse the area with water.

If you’ve got a small, older stain, you can use a detergent like baking soda, vinegar, washing up liquid or laundry detergent. Cover the stain with the detergent and leave for about 30 minutes. Then, add hot water and scrub the area and rinse. You might need to repeat this if necessary.

If it’s a larger, more stubborn stain, you might need to use a special degreaser. You can use this similarly to a detergent but make sure you follow the instruction on the bottle carefully.

How To Lay Block Paving

Do you wish to know how to install block paving? We’ve got you covered! Here, you’ll find a useful step by step guide that’ll provide you with all the necessary information to lay a wide range of block paving products available in the market today. You must, however, note that the installation of block paving can be a tricky affair and should not be attempted unless you have undergone a proper training or have a good experience in the field. If otherwise, we’d advise you to leave the task for a reliable block laying professional to guarantee the best results and also avoid making costly mistakes.

lDesign

• Draw up a design to perfectly suits your needs.

• Decide on the type of block as well as colour.

lExcavation

• Use a mini excavator or a JCB ( depending on the size of the job) to excavate the driveway.

• Identify and mark out the area to be excavated.

• Dug out the area until you reach a suitable level

• Ensure that the proposed finish level is 150mm underneath the damp proof course in any of the adjoining building’s brick.

lEdge Restraints

• Build a 100mm depth-thick concrete foundation with the help of a concrete mixer, 1 part cement and 6 parts ballast.

• Position the kerb unit on top of the level with a string line and spirit level.

• Use a trowel and rubber mallet to mortar the kerb unit to the foundation.

• Haunch the back of the kerb units in such a way that the concrete reach half way up the kerb’s rear.

lSubbase

• Put the crushed concrete in the edge restraints and ensure it’s at the desired level of 50mm.

• Use a vibrating plate to compact and level

lScreeding

• Apply a layer of sharp sand (to 50mm depth) and campact it using a vibrating plate.

• Apply second layer of sharp sand (to 20mm depth) on top of the first layer.

• Level the second layer to the correct falls.

lInstallation Of Paving

• Lay the block paving starting from the bottom of a slope.

• Ensure the blocks are placed at about 10mm to 15mm above the required finish level.

• Make sure the blocks used are between 3-5 packs as you proceed with your desired pattern. You may need to cut smaller block pieces to fill smaller gaps.

lFinishing Touches

• Clear out the area to ensure no debris is left on the blocks.

• Put kiln dried sand and brush across the whole of the area, ensuring the sands falls between the blocks’ joints.

• Compact the drive with the vibrating plate.

• Brush more kiln dried sand over the area and compact again

• Repeat the process until the joints are full of sand.

Moss growth on tarmac and asphalt is pretty common. This can make your driveway or outside area slippy and untidy, so it’s a good idea to get rid of it.

Start by using a stiff brush to dislodge as much moss as possible and clear it off your driveway. Then use a moss killer to kill any remaining moss. Make sure you follow the product instructions – some moss killers are best used on tarmac or asphalt that’s clean and damp, whilst others are better for dry surfaces.

To prevent further moss growth, it’s a good idea to reduce the amount of shade on your tarmac or asphalt as much as possible. This will help you keep it as warm and dry as possible, and reduce moss growth.

If your concrete driveway’s looking grubby, it’s best to try cleaning it with water and a brush, or a mild detergent. However, if this doesn’t work, it can be worth trying bleach.

Dilute your bleach down to 50% bleach and 50% water, and apply it to your driveway. Leave it for 10 minutes, then scrub it using gloves and a stiff brush. Finish by rinsing your driveway off with clean water.

It’s important to remember that bleach can stain certain surfaces and kill plants. So, if you’re concerned about materials and boarders around your driveway, it might be best to use a different type of detergent, like floor cleaner or degreaser.

Gravel is the cheapest driveway surfacing material. Asphalt costs a little more than gravel, and concrete is significantly more expensive. The cost of paving depends on the material you use. Obtain as many quotes as possible as materials and costs differ from company to company.

From gravel and crushed stones to asphalt and tarmac, the choice when it comes to surfacing options for driveways is truly staggering. However, what’s not too clear is the options that best suits a sloping driveway. If you also possess a sloping driveway and wondering the best material to install, you’re definitely not alone. This is a major source of concern for several home and property owners in the UK being fully aware that making the wrong choice here can prove really costly and disastrous. In order to help you make the best informed decision possible, we’ve put together this post which takes a look at the various driveway material options available to you.

• Gravel
  This driveway surfacing option provides a truly enjoyable “crunch sound when driven on, however, the satisfaction will be short lived if installed on a sloped driveway. If installed on a sloped driveway, there’s going to be a continual displacement as instinctively rolls downhill on an incline.

• Concrete
  This can prove to be a great problem if installed on an incline. This is due to the fact that concrete is subject to freeze/thaw phenomenon which makes it steep and slippery lacking the needed traction.

• Tarmac
  This is particularly far from ideal when it comes to a steep driveway surface. This is because it requires continuous maintenance to prevent spillages from spoiling the surface.

• Resin
  The best surface for a steep driveway is simply that made from resin. This is due to the fact that this surfacing option allows water to soak away naturally. They’re perfectly permeable, preventing water from pooling and reducing the risk of falls.