Find a Driveway Installer you can trust in Pickering.

The most commonly used driveway surfacing materials are gravel, asphalt, concrete and paving - which can be block, slabbed or patten imprinted. Take a look at our product information pages to help you decide which one to use and which one will look best for your driveway.

While resin bound and resin bonded driveways have similar names, it might surprise you to know that they’re very different. Both paving systems use resin and aggregates (stones) to form a fixed surface, but there are plenty more differences than there are similarities.

Resin bound driveways are made from a resin and aggregate mix that is trowelled onto a bitmac or concrete base. It leaves a smooth, flat finish and you won’t find any loose gravel. It’s also a pourous surface, which means that rainwater can pass through into the ground, avoiding pools and flooding.

However, resin bonded driveways involve spreading resin across a base, then scattering aggregate into it. Most of the stones will stick to the resin, but some will stay loose. That means you’ll get the effect of loose gravel without so much to sweep and take care of. Because the stones are scattered onto a complete layer of resin, water can’t pass through it. That means you could end up with water pooling, and it also means that a resin bonded driveway isn’t frost resistant, meaning it could get slippery.

So which is better – a resin bound or resin bonded driveway? The answer depends on a few things. If you have a period property where a smooth, shiny surface might not complement the look of your home, you might want to go for resin bonded. If you need lots of grip, for example if you’re a wheelchair user, resin bonded may also be the way to go – even though resin bound surfaces still offer enough grip for sloped driveways and ramps. But if you want a low-maintenance, weed-free, permeable surface, resin bound driveways are the way to go.

If you’re considering laying gravel on your driveway, then you’d probably want to know the amount of gravel you’ll need to complete the project. When you are calculating the amount of gravel you’ll require to cover your driveway, there’s an important factor you’ll need to consider and that is the type of gravel you opt for such as a crushed or pea gravel. There are varying grades which are found in particles from fine to course, with a size ranging from 2mm to 64mm. Therefore, there’s a need to estimate the volume of the gravel while also having the rock’s size in mind. Also, there’s a need to select your most preferred gravel which you’ll like to use before proceeding to dig the depth of your driveway and subsequently determine the amount of gravel that’ll be needed using these excellent tips.

✓ Determine the size and coverage. As you would have expected, the smaller the gravel is, the bigger the coverage will be, and gravels should be at least 4 inches deep. However, if the rocks happen to be a bit large then you can allow for an extra 1/2 inch.

✓ Measure the driveway. Multiply the width by the length and depth to get the size of the driveway in cubic feet. Meanwhile for cubic yards, you can divide the total cubic feet by 27. This is due to the fact that one cubic feet is same as 1.13 tons.

✓ Working with gravel. Here, you’ll have to calculate an underlay measurements differently. You can use 2 inches of road base that’ll be overlaid with 2 inches of gravel.

1. Prepare the base If you want your resin bound driveway to last a long time, you need to ensure that you prepare the base properly. Remove any block paving, grass or soil and dig down until you hit solid ground. Lay a sub-base of asphalt for good permeability. If you’re laying over the top of your current driveway, make sure that all cracks are increased into a ‘v’ shape with a saw and ensure the surface is dry and weed-free.
2. Mix the resin You must follow the instructions on the materials you have to the letter if you want the curing process to work. Usually batches come in ‘Part A’ and ‘Part B’. Keep the resin container secure and on a protective surface to avoid splashing, then mix Part A for 10-20 seconds at a slow speed with a helical bladed mixer. Add Part B and mix thoroughly at a slow speed for about 2 minutes until it’s blended together.
3. Mix the dried aggregates and sand with the resin Place a quarter of the aggregates into a mixer, then add the pre-mixed resin and start a stopwatch. You should then add the rest of the aggregates before slowly adding the sand. When you’re happy with that mix, stop the stopwatch. That time is the time that you need to spend mixing any other resin and aggregates to avoid colour variation.
4. Lay the mix on the surface Transfer the mix to the work area then plan a laying route. When the mix is laid out, use a very clean trowel to spread the mix. Clean it regularly during the process to avoid dragging aggregates out of place. Once the aggregates stop moving in a fluid movement and become solid, stop trowelling. Then you can polish the surface to give it an attractive shine.

Do you want to install a new patio? If yes, then on top of the agenda will definitely be the cost of paving slabs. However providing a single and accurate estimate to the cost of your new patio is almost impossible as there are many factors that can influence what the price would be. These factors include the size of the area, the choice of stone, installations and lots more.

To get a more accurate estimate of your cost there’s is the need to look at some factors before calculation. These includes envisioning your patio as well as putting the drainage in mind. Firstly, you’ll need to decide where you want your patio to be - this should include considering whether you’ll get enough privacy sitting on your patio and more. If you’re able to identify where to put your patio, you’ll be able to have a clearer idea of the potential shape and size of the patio. Secondly, there’s a need to consider the drainage because failure to provide adequate drainage will only result in storing of water which leads to a development of algae or vegetation across your patio.

The material you opt for is also a huge determinant of your patio’s cost. When it comes to paving slabs you’ll only get what you pay for. Deciding to go for cheaper paving slabs will most likely lead to frequent staining, slippery surface, tough maintenance as well as constant cracking. Consequently, the act of cutting back on the cost of paving slabs will only you cost you more money in the long run. What’s more? If you have an existing patio you’d like to replace, then you’d probably need to include the cost of removing the existing one.

If you’re considering getting a new tarmac driveway or outside area, it’s important to know how long it takes to dry. Try to use it too early and you might damage it and ruin its appearance.

It won’t be long before you can walk on your new surface, as long as you’re careful. However, it’s a good idea to avoid putting heavy objects or driving on it for 2-3 days. For a more accurate timescale, ask your tarmac paving and driveway pro.

While many professionals will recommend a pressure washer to clean block paving, it’s possible to clean your paving without one – just scrub the affected areas with a firm bristled brush and use plenty of soap. Then, rinse off the area with clean water.